Yoshie Aoyagi

Comparison of low-level polycyclic aromatic hydrocarbons in sediment revealed by Soxhlet extraction, microwave-assisted extraction, and pressurized liquid extraction.

We analyzed polycyclic aromatic hydrocarbons (PAHs) present in lake sediment at low levels (<1 microg g(-1)) by using Soxhlet extraction (Soxhlet), microwave-assisted extraction (MAE), and pressurized liquid extraction (PLE) in combination with gas chromatography and isotope-dilution mass spectrometry. Although all extraction techniques showed good repeatability for five target PAHs (relative standard deviation <5.2%, n=3), the results decreased in the order PLE>MAE>Soxhlet. Differences in the results originated mainly from differences in the extraction efficiencies of the techniques for native PAHs, because all techniques gave comparable recovery yields of corresponding 13C-labeled PAHs (13C-PAHs) (51-84%). Since non-negligible amounts of both native PAHs and 13C-PAHs were re-adsorbed on matrix in MAE, not only recovery yields of 13C-PAHs but also efficiencies of extraction of native PAHs should be examined to evaluate the appropriateness of any analytical procedures.

Evaluation of the impact of matrix effect on quantification of pesticides in foods by gas chromatography-mass spectrometry using isotope-labeled internal standards.

The impact of the matrix effect in GC-MS quantification of pesticides in food using the corresponding isotope-labeled internal standards was evaluated. A spike-and-recovery study of nine target pesticides was first conducted using paste samples of corn, green soybean, carrot, and pumpkin. The observed analytical values using isotope-labeled internal standards were more accurate for most target pesticides than that obtained using the external calibration method, but were still biased from the spiked concentrations when a matrix-free calibration solution was used for calibration. The respective calibration curves for each target pesticide were also prepared using matrix-free calibration solutions and matrix-matched calibration solutions with blank soybean extract. The intensity ratio of the peaks of most target pesticides to that of the corresponding isotope-labeled internal standards was influenced by the presence of the matrix in the calibration solution; therefore, the observed slope varied. The ratio was also influenced by the type of injection method (splitless or on-column). These results indicated that matrix-matching of the calibration solution is required for very accurate quantification, even if isotope-labeled internal standards were used for calibration.

Development of certified reference material for quantification of two pesticides in brown rice.

Brown rice powder certified reference material, NMIJ CRM 7504-a, for the analysis of pesticide residues was developed by the National Metrology Institute of Japan, part of the National Institute of Advanced Industrial Science and Technology. Brown rice sample was harvested to contain the pesticides such as etofenprox and fenitrothion, and that was collected from a field in Ibaraki Prefecture in Japan. The certification was carried out using multiple analytical methods such as pressurized liquid extraction, homogenization, and solid-liquid extraction (shaking); the values of target pesticides were obtained by isotope dilution mass spectrometry. Certified values were 0.19 +/- 0.05 mg/kg and 0.109 +/- 0.017 mg/kg for etofenprox and fenitrothion, respectively.

Species-specific isotope dilution analysis of mono-, di, and tri-butyltin compounds in sediment using gas chromatography-inductively coupled plasma mass spectrometry with synthesized 118Sn-enriched butyltins

A species-specific isotope dilution (ID) method is described for the determination of mono-, di, and tri-butyltin compounds in sediment by gas chromatography-inductively coupled plasma mass spectrometry (GC-ICP-MS), where the mixture of 118Sn-enriched butyltin compounds synthesized in our laboratory was used as a spike. A correction method for the mass bias, a quantitative extraction of the butyltins from sediment, and an assay for the concentration of the standard solution for the reverse ID procedure were investigated to achieve a reliable ID analysis. The spike solution was added with tri-propyltin (TPrT), and the butyltins were extracted by mechanical shaking into acetic acid-tropolone-toluene. The extracted butyltins were ethylated with sodium tetraethylborate and measured by GC-ICP-MS. The mass bias correction factor for the butyltins was calculated with the measured area ratio of 120Sn/118Sn of TPrT in each chromatographic run, and the correction was carried out. The mass bias was well corrected with this in-run correction (the standard uncertainties of the corrected 120Sn/118Sn for the butyltins were in the range 0.03-0.45%, typically 0.25%, with triplicate measurement corresponding to 0.02-0.37% mass bias). The extraction efficiency of mono-butyltin (MBT) from sediment was improved by using tropolone-toluene as the solvent. Well-defined standard solutions for the reverse-ID procedure could be obtained by an assay for the purities of the natural abundance butyltin chloride reagents used for preparing the standard solutions. Overall uncertainties associated with the present method were estimated, where the sediment certified reference materials, PACS-2 and BCR 646, were analyzed. The uncertainty arising from the extraction was the main contributor to the overall uncertainties for MBT and di-butyltin (DBT) determinations, while with the case of tri-butyltin (TBT) determination the uncertainties arising from the purity of TBT chloride reagent used for preparing the standard solution was a large contributor to the overall uncertainties although the uncertainty arising from the extraction was also a main contributor. The analytical results of MBT, DBT, and TBT in both reference materials, except for MBT results in PACS-2, were in good agreement with the certified values in each. The result of MBT in PACS-2 (0.677 +/- 0.049 microg g(-1) as tin, mean +/- expanded uncertainty) was significantly higher than the certified value (0.45 +/- 0.05 microg g(-1)), but closely matched with the lately reported values (Rajendran, Tao, Nakazato and Miyazaki, Analyst, 2000, 125, 1757: 0.62 +/- 0.02 microg g(-1); Chiron, Roy, Cottier and Jeannot, J. Chromatogr. A, 2000, 879, 137: 0.634 +/- 0.082 microg g(-1); Alonso, Encinar, Gonzalez and Sanz-Medal, Anal. Bioanal. Chem., 2002, 373, 432: 0.64 +/- 0.04 microg g(-1). The present method is concluded to be reliable for the determination of MBT, DBT, and TBT in sediment.

Development of apple certified reference material for quantification of organophosphorus and pyrethroid pesticides

An apple certified reference material for the analysis of pesticide residues was issued by the National Metrology Institute of Japan. Organophosphorus and pyrethroid pesticides were sprayed on apples, and these were used as raw materials of certified reference material. The harvested apples were cut into small pieces, freeze-dried, pulverized, sieved, placed into 200 brown glass bottles (3g each), and sterilized by γ-irradiation. Stability and homogeneity assessment was performed, and the relative uncertainties due to instability (for an expiry date of 32 months) and inhomogeneity were 10.3-25.0% and 4.0-6.8%, respectively. The characterization was carried out using multiple analytical methods to ensure the reliability of analytical results; the values of target pesticides were obtained by isotope dilution mass spectrometry. Certified values were 2.28 ± 0.82 mg/kg for diazinon, 3.14 ± 0.79 mg/kg for fenitrothion, 1.55 ± 0.81 mg/kg for cypermethrin, and 2.81 ± 0.70 mg/kg for permethrin.

Accurate quantification of polycyclic aromatic hydrocarbons in dust samples using microwave-assisted solvent extraction combined with isotope-dilution mass spectrometry.

For accurate quantification of polycyclic aromatic hydrocarbons (PAHs) in dust samples, we investigated the use of microwave-assisted solvent extraction (MAE) combined with isotope-dilution mass spectrometry (IDMS) using deuterium-labelled PAHs (D-PAHs). Although MAE with a methanol/toluene mixture (1:3 by volume) at 160°C for 40 min was best for extracting PAHs from tunnel dust among examined, the recovery yields of D-PAHs decreased with increasing molecular weight (<40% for MW≥264; that of deuterium-labelled indeno[123-cd]pyrene (D-IcdP) was only 7.1%). Although the residues were extracted a second time, the observed concentrations did not change dramatically (<5%), and the recovery yields of heavier D-PAHs (i.e., MW≥264) were approximately half of those of the first extract, including D-IcdP (3.4%). These results suggest that both partitioning and isotopic equilibria of PAHs and D-PAHs between sample and solvent were achieved for extractable heavier PAHs under the condition. Thus, the observed concentrations of PAHs obtained by MAE-IDMS were reasonable, even though recovery yields of D-PAHs were <50%. From the results of carbon analyses and extractable contents, lower recovery yields of D-PAHs from the tunnel dust were due to a large content of char with low extractable contents.

Development of soybean certified reference material for pesticide residue analysis

A soybean certified reference material for pesticide residue analysis was developed by the National Metrology Institute of Japan. Three organophosphorus (diazinon, fenitrothion, chlorphyrifos) and one pyrethroid (permethrin) pesticides were sprayed on soybeans three times before harvest. These soybeans were freeze pulverized, homogenized, bottled, and sterilized by γ-irradiation to prepare the candidate material. Three isotope-dilution mass spectrometric methods that varied in terms of the solvents used for extraction of the target pesticides, the clean-up procedure, and the injection techniques and columns used for quantification via gas chromatography/mass spectrometry were applied to the characterization. Each target pesticide was quantified by two of these analytical methods, and the results were in good agreement. Homogeneity and stability assessment of the material demonstrated that the relative standard uncertainties due to the inhomogeneity and the instability for an expiry date of 55 months were 1.89-4.00% and 6.65-11.5%, respectively. The certified pesticide concentrations with expanded uncertainties (coverage factor k=2, approximate 95% confidence interval) calculated using the results of the characterization and the homogeneity and stability assessment were 21.7 ± 3.2 μg/kg for diazinon, 88 ± 21 μg/kg for fenitrothion, 11.1 ± 3.2 μg/kg for chlorpyrifos, and 20.1 ± 4.3 μg/kg for permethrin (as the sum of the constituent isomers).

Development of green onion and cabbage certified reference materials for quantification of organophosphorus and pyrethroid pesticides.

Green onion and cabbage certified reference materials for the analysis of pesticide residues were issued by the National Metrology Institute of Japan, part of the National Institute of Advanced Industrial Science and Technology. Green onion and cabbage samples were grown so as to contain several kinds of organophosphorus and pyrethroid pesticides, and those were collected from a field in the Kochi Prefecture in Japan. The certification was carried out by using multiple analytical methods to ensure the reliability of analytical results; the values of target pesticides (diazinon, fenitrothion, cypermethrin, etofenprox, and permethrin for green onion and chlorpyrifos, fenitrothion, and permethrin for cabbage) were obtained by isotope dilution mass spectrometry. Certified values of target pesticides were 0.96-13.9 and 2.41-6.9 mg/kg for green onion and cabbage, respectively. These are the first green onion and cabbage powder certified reference materials in which organophosphorus and pyrethroid pesticides are determined.

Evaluation of pressurized liquid extraction for the analysis of four pesticides in unpolished rice

The aim of to evaluate efficiency of this study was extraction pressurized liquid extraction (PLE) for the analysis of four pesticides, fthalide, etofenprox, fenitrothion, and isoprothiolane, in unpolished rice by comparing with homogenization as a reference technique. The concentrations of four selected pesticides obtained by PLE with acetonitrile at 130°C for 10 min × 2 cycles were comparable to those by homogenization with water-soaking. The repeatability of the analysis, represented as relative standard deviations (RSDs), were 1.4–3.6% (n = 3) for PLE at 130°C and 1.2–3.8% (n = 3) for homogenization with water-soaking. Recovery yields of surrogates were 75–88% and 87–109% for PLE at 130°C and homogenization with water-soaking, respectively, and these were satisfactory according to the method of positive list. This study suggested that PLE can be applied for the analysis of selected four pesticides in unpolished rice as well as homogenization with water-soaking.

MECHANISM OF IONIZATION OF POLYCYCLIC AROMATIC HYDROCARBONS BY A TOLUENE/ANISOLE MIXTURE AS A DOPANT IN LIQUID CHROMATOGRAPHY/DOPANT-ASSISTED ATMOSPHERIC-PRESSURE PHOTOIONIZATION/MASS SPECTROMETRY

Ionization mechanisms of 16 polycyclic aromatic hydrocarbons (PAHs) by dopant-assisted atmospheric-pressure photoionization (DA-APPI) with a toluene/anisole mixture as a dopant were examined in the reversed-phase liquid chromatography mode with a methanol/water to acetonitrile linear gradient mobile phase. When toluene/anisole mixtures were used as dopants, their characteristics were governed by anisole. Since the IE of anisole (8.20 eV) is below that of toluene (8.83 eV), anisole is ionized not only by photons from the krypton lamp but also by charge transfer from toluene radical cations. In the latter half of chromatogram, when acetonitrile was dominant in the eluent, ions originating from both toluene and anisole decreased while acetonitrile-cluster ions began to increase. Because acetonitrile-cluster ions are not formed with anisole alone, but are formed with toluene alone, toluene radical cations would be consumed to form acetonitrile-cluster ions.