Yuanzhong Lei

Development of wide-bore conduction-cooled superconducting magnet system for material processing applications

The application of high magnetic field to material processing, so called electromagnetic processing of material (EPM) has been recognized as cutting edge technology, especially in the field of advanced material processing. It is the most effective methods to control thermal, mass and energy transfer during material solidification. A wide-bore conduction-cooled superconducting magnet with operating current of 116 A was designed, fabricated and tested for the material processing devices. The superconducting magnet has the effective warm hole of 18 cm, the maximum center field of 6 T and homogeneity of 5% in diameter of 5 cm. After the Nb/sub 3/Sn coil insert installed, the magnet can provide the maximum center field of 10 T with effective warm bore of 10 cm. A second-stage GM cryocooler with the second-stage cooling power of 1 W is used to cool the superconducting magnet from room temperature to 4.2 K. In this paper, the design, fabrication, test, stress analysis and quench protection characteristics are presented.

A Superconducting Magnet System for Whole-Body Metabolism Imaging

A 9.4 Tesla superconducting magnet is designed and fabricated with a warm bore of 800 mm for neuroscience research. The superconducting magnet will be made of a NbTi Wire-in-Channel (WIC) conductor with a higher ratio of copper to non-copper, which thus sustains the high stresses. It is cooled to operate temperature at 4.2 K liquid helium. The cryostat system is cooled through GM cryocoolers, some used to cool the radiation shield, and the others realize the re-condensed liquid helium. The MRI magnet system has a high level of stored energy, about 134 MJ, and a relatively-lower nominal current, about 212.5 A. The magnet will be operated in a persistent current mode with a superconducting switch. The WIC wires are employed to meet the cryostability criteria to avoid any risks from quench. The protection circuit with the subdivision of the coil reduces the terminate voltage and hot-spot temperature. In the paper, the specifications of magnet system will be presented.

Design and Fabrication of a Conduction-Cooled High Temperature Superconducting Magnet for 10 kJ Superconducting Magnetic Energy Storage System

A high temperature superconducting (HTS) magnet for 10 kJ superconducting magnetic energy storage (SMES) system is designed by an improved optimal algorithm and cooled through GM cryocooler. In order to demonstrate the technology, a model HTS magnet made of Bi-2223/Ag tape to fabricate double-pancakes with the inner and outer diameters of 120 mm, 207.1 mm and height of 119 mm was fabricated and tested. The magnet is operating with GM cryocooler at 10 K. We have tested the Bi2223 HTS magnet at various ramping rates with 0.1-5.06 A/s. The experimental results show that the model HTS magnet is operating very stable. In the paper, we report the design of the HTS-SMES and fabrication technique for the model HTS magnet

Tests on a 6 T Conduction-Cooled Superconducting Magnet

A 6 T conduction-cooled superconducting magnet was designed, fabricated and tested. The magnet is composed of two coaxial NbTi solenoid coils with identical axial length. Clear bore of the magnet is phi 226 mm. The magnet is installed in a vacuum cryostat with a phi 100 mm room temperature bore. The cryostat is designed in a support frame to be rotatable in a horizontal or vertical direction. A two-stage 4 K Gifford-McMahon (GM) cryocooler is used to cool down the superconducting magnet from room temperature to 4 K. The cooling power of the 4 K cold head is 1 W. A pair of Bi-2223 high temperature superconducting current leads was employed to reduce heat leakage into 4 K cold mass. Total cold mass of the superconducting magnet is about 115 kg. It takes 82 hours to cool down the magnet from 300 K to 4 K directly through the cryocooler. The superconducting magnet reached the designed central magnetic field of 6 T in the warm bore when a 115 A energizing current is applied. The superconducting magnet was stably operating more than 275 hours continuously in full field. Further, a Nb3Sn coil insert to be installed, the magnet can provide the maximum center field of 10 T with effective warm bore of phi 100 mm. In this paper, the detailed design, fabrication and test are presented

High Magnetic Field Superconducting Magnet for 400 MHz Nuclear Magnetic Resonance Spectrometer

A superconducting magnet with the center field of 9.4 T is designed and fabricated for 400 MHz Nuclear Magnetic Resonance. Superconducting coil with NbTi/Cu superconducting wire is employed and cooled by re-condensed liquid helium and the magnet system with the clear-bore of 54 mm. The pulsed tube refrigerator with separated valve is employed to cool the magnet system. The superconducting magnet has an active shield with high pure copper shield to protect during quench of the shielding coil. The paper reports the electromagnetic design, and fabrication is detailed.

Structural Design of a 9.4 T Whole-Body MRI Superconducting Magnet

A project to develop a 9.4 T magnetic resonance imaging system is proposed for bioscience research applications. A whole body superconducting magnet system will be manufactured and test in the Institute of Electrical Engineering, Chinese Academy of Sciences (IEE, CAS). This magnet system features a room temperature bore of 800 mm in diameter, helium bath cooing, 9.4 T center magnetic field and passive iron shielding. The magnet is designed with radial layer-winding method. Five coaxial coils will be wound independently and assembled together as the main magnet. Coil length of the magnet is 3000 mm. In the magnet design, current density grading is performed to optimize the magnetic field distribution and stress level in the coil windings. The maximum magnetic field is 9.505 T, corresponding to an operating current of 224.515 A. The total magnetic energy storage is 138 MJ. Detailed magnetic and mechanic structure design as well as structure stress analysis are presented in this paper.

An 8 T Superconducting Split Magnet System With Large Crossing Warm Bore

A conduction-cooled superconducting split magnet system with large crossing warm bore is designed and will be developed for material processing applications. The magnet is composed of eight coaxial coils and assembled in the form of split coil groups. Both the Bi2223/Ag HTS superconducting tape and NbTi LTS superconducting wires are used to generate a central magnetic field of 8 T, maximum of 11 T in the horizontal warm bore. The split gap between the coils is as large as 136 mm to accommodate the crossing warm bore of 100 mm in diameter. The superconducting split magnet will be conduction-cooled by two GM cryocoolers. The HTS coils and NbTi coils are to be operated in driven mode with two independent power supplies. The operation currents are 200 A (HTS) and 136 A (NbTi) respectively. Magnetic design, stress and strain analysis as well as magnet operation and protection are presented in this paper.

Design and Test of Conduction-Cooled High Homogenous Magnetic Field Superconducting Magnet for Gyrotron

A conduction-cooled superconducting magnet with the warm room of Phi 80 mm and the center field of 0~4 T was designed, fabricated and tested. The magnet can be operated for two different sets of coils which have different homogenous regions with lengths of 150 mm and 250 mm. The homogeneity of magnetic field is about plusmn0.25%. All the homogeneous regions are with the same starting point. The center field is decayed to 1/6-1/7 from the original point to 195 mm. The operating temperature of the magnet is defined at the 5.5 K for the conduction-cooled magnet to take into account the temperature rise during charging current. The thermal equilibrium of the superconducting magnet and cryogenic system is analysed to define ramping rate, operating current and margin of superconducting magnet. The detailed design and fabrication of the superconducting magnet for gyrotron are discussed. The test results show that the superconducting magnet can generate the requirement of magnetic field distribution.

A Passive Quench Protection Design for the 9.4 T MRI Superconducting Magnet

A passive quench protection design of the 9.4 T whole-body magnetic resonance imaging superconducting magnet is proposed. The design of the coil subdivision with shunt resistors is introduced. The selection of the configuration of the heater network is detailed. The optimization of the geometric parameter of the heater strips and the thickness of the insulation binding outside the heater strips are discussed. A winding sequence that could accelerate the quench propagation in the compensating coil is proposed. The calculation results show that the optimized quench protection design can guarantee the safety of the magnet in the case of any coil as the quench initiation coil.

Conduction-Cooled Superconducting Magnet With Persistent Current Switch for Gyrotron Application

A superconducting magnet with a center field of 4.5 T cooled by GM cryocooler and operated in the persistent current mode has been designed, fabricated and tested for gyrotron. The superconducting magnet has a warm bore with diameter of 90 mm, the homogenous region with the diameter of 40 mm and length of 230 mm. The ratio of the axial field to the center field located at 180 mm is lower than 88%. In the other special points, the ratios of the radial field to the axial field should be less than from 3% to 11%. The thermally-controlled NbTi/CuNi switch with superconducting joint is connected to the conduction cooled magnet. In this paper, the detailed design, fabrication and test are reported.