Zdenek Remes

Nanostructured three-dimensional thin film silicon solar cells with very high efficiency potential

We report on the experimental realization of amorphous/microcrystalline silicon tandem solar cells (Micromorph) based on our three-dimensional design. An enhancement is reached in the short-circuit current by 40%, with an excellent open-circuit voltage of 1.41V and a fill factor of 72%. We have used nanoholes or microholes dry etched into the ZnO front contact layer. Monte Carlo optical modeling shows that stable efficiency of amorphous silicon p-i-n solar cells in over 12% range is possible. For the Micromorph cells, efficiency over 15% with the thickness of amorphous Si below 200 nm and of microcrystalline Si around 500 nm is possible.

Organic-Inorganic Halide Perovskites: Perspectives for Silicon-Based Tandem Solar Cells

We investigate the efficiency potential of organic-inorganic halide perovskite/crystalline silicon tandem solar cells, a new class of photovoltaic devices targeting long-term cost reductions by ultrahigh conversion efficiencies. Methyl ammonium lead triiodide perovskite solar cells are particularly interesting as the top cell in Si-based tandem devices due to their suitable band gap, high photovoltage, and low sub-bandgap absorption. We derive optical models for a perovskite/Si tandem cell with Lambertian light trapping in the perovskite top cell, as well as for a top cell in the single pass limit. We find that unlike for other thin-film device architectures, light trapping is not required for the triiodide perovskite/Si tandem to reach matched top and bottom cell currents. While a Lambertian top cell could be employed in a four-terminal tandem, a top cell in the single pass limit enables a current-matched monolithic device with realistic top cell thicknesses. We calculate a limiting efficiency of 35.67% for an ideal (no parasitic absorption, ideal contacts) monolithic tandem, assuming a top cell open-circuit voltage of 1100 mV.

Determination of absorption cross-section of Si nanocrystals by two independent methods based on either absorption or luminescence

Absorption cross-section (ACS) of silicon nanocrystals (SiNCs) is determined via two completely independent approaches: (i) Excitation-intensity-dependent photoluminescence (PL) kinetics under modulated (long square pulses) pumping and (ii) absorbance measured by the photothermal deflection spectroscopy combined with morphology information obtained by the high-resolution transmission electron microscopy. This unique comparison reveals consistent ACS values around 10−15 cm2 for violet excitation of SiNCs of about 3–5 nm in diameter and this value is comparable to most of direct band-gap semiconductor nanocrystals; however, it decreases steeply towards longer wavelengths. Moreover, we analyze the PL-modulation technique in detail and propose an improved experimental procedure which enables simpler implementation of this method to determine ACS of various (nano)materials in both solid and liquid states.

Design and investigation of properties of nanocrystalline diamond optical planar waveguides

Diamond thin films have remarkable properties comparable with natural diamond. Because of these properties it is a very promising material for many various applications (sensors, heat sink, optical mirrors, chemical and radiation wear, cold cathodes, tissue engineering, etc.) In this paper we report about design, deposition and measurement of properties of optical planar waveguides fabricated from nanocrystalline diamond thin films. The nanocrystalline diamond planar waveguide was deposited by microwave plasma enhanced chemical vapor deposition and the structure of the deposited film was studied by scanning electron microscopy and Raman spectroscopy. The design of the presented planar waveguides was realized on the bases of modified dispersion equation and was schemed for 632.8 nm, 964 nm, 1 310 nm and 1 550 nm wavelengths. Waveguiding properties were examined by prism coupling technique and it was found that the diamond based planar optical element guided one fundamental mode for all measured wavelengths. Values of the refractive indices of our NCD thin film measured at various wavelengths were almost the same as those of natural diamond.

Optimum performance solar cells using atmospheric pressure chemical vapour deposition deposited TCOs

High performance transparent conducting oxides (TCOs), have significance for optimising PV performance. We have developed an advanced atmospheric pressure chemical vapour deposition process, by applying fast experimentation and using a combinatorial chemistry approach to aid the studies. The deposited films were characterised for crystallinity, morphology (roughness), haze and resistivity to aid optimisation of material suitable for solar cells. Optical measurements on these samples showed low absorption losses, less than 1% around 500 nm for one pass, which is much lower than those of industrially available TCOs. Selected samples were then used in manufacture of single junction a-Si : H solar cells, which showed high initial solar energy conversion efficiencies up to 9.3% and high short circuit current densities of 15 mA/cm². Compared with (commercially available) TCO CVD coated glasses, these TCO coatings show excellent performance resulting in a high quantum efficiency yield for a-Si : H solar cells.

Optical characterisation of organosilane-modified nanocrystalline diamond films

We report on an optical characterisation of nanocrystalline diamond films photochemically functionalised with the organosilane-coupling agent, N1-(3-(trimethoxysilyl)propyl)hexane-1,6-diamine (alternative names: N-(6-aminohexyl)aminopropyl-trimethoxysilane, (3-(6-aminohexylamino)propyl) trimetoxysilane, AHAPS). The presence and homogeneity of the organosilane layers were detected by fluorescence microscopy and infrared reflectance-absorbance spectroscopy. The results indicated that a homogeneous surface coverage with organosilane layers was achieved on diamond surfaces which were modified either by hydrogen or by oxygen plasma treatment. The functionalised nanocrystalline diamonds present a promising solution in future biosensor applications.

Nanostructured diamond layers enhance the infrared spectroscopy of biomolecules.

We report on the fabrication and practical use of high-quality optical elements based on Au mirrors coated with diamond layers with flat, nanocolumnar, and nanoporous morphologies. Diamond layers (100 nm thickness) are grown at low temperatures (about 300 °C) from a methane, carbon dioxide, and hydrogen gas mixture by a pulsed microwave plasma system with linear antennas. Using grazing angle reflectance (GAR) Fourier transform infrared spectroscopy with p-polarized light, we compare the IR spectra of fetal bovine serum proteins adsorbed on diamond layers with oxidized (hydrophilic) surfaces. We show that the nanoporous diamond layers provide IR spectra with a signal gain of about 600% and a significantly improved sensitivity limit. This is attributed to its enhanced internal surface area. The improved sensitivity enabled us to distinguish weak infrared absorption peaks of <10-nm-thick protein layers and thereby to analyze the intimate diamond-molecule interface.

Optimization of Solar Cell Performance using Atmospheric Pressure Chemical Vapour Deposition deposited TCOs

High performance transparent conducting oxides, in particular doped SnO2, have significance for optimising photovoltaic cell performance. The surface morphology and resistivity are crucial to the performance of the final PV solar cell. There are three key objectives for the TCO properties. Firstly, the enhancing of optical scattering to improve efficiency of light absorption. Secondly, it is important to minimise absorption losses, as these impact directly on efficiency due to loss of photons available to the PV absorber layers. Thirdly, the TCO has to meet minimum conductivity requirements set by cell configuration designs. Typically these require about 10 Ohms/sq or less and so a TCO material capable of efficient doping, and a degree of nanostructure control for carrier mobility is sought for maximum performance.

On the way to enhance the optical absorption of a-Si in NIR by embedding Mg2Si thin film

Mg2Si thin film was embedded in amorphous silicon matrix by solid phase epitaxy. The structure and optical properties were investigated by electron energy loss, X-ray photoelectron, Raman, and photo thermal deflection spectroscopy measurements. It was found that in the photon energy range of 0.8–1.7 eV, the light absorption of the structure with magnesium silicide (Mg2Si) film embedded in a-Si(i) matrix is 1.5 times higher than that for the same structure without Mg2Si.

Single Crystal CVD Diamond growth and characterizations

Due to its radiation harness, single crystal CVD diamond is a remarkable material for the construction of detectors used in hadron physics and for medical therapy. In this work, single crystal CVD diamond plates were grown in a microwave plasma reactor, using home design substrate holder and a relatively high pressure. Optical Emission Spectroscopy was employed during the MW-PECVD growth to characterize excited species present in the plasma and to detect the presence of residual gases such as nitrogen which is unsuitable for detectors applications. The samples were characterized using various methods such as Raman spectroscopy, photoluminescence (PL), photocurrent spectroscopy, Raman mapping, birefringence microscopy, optical microscopy and also AFM. The best sample, exhibits a FWHM for the 1332 cm −1 Raman peak about 1.6 cm −1 . Room temperature PL spectra showed no N–related luminescence, confirming the high quality of the grown single crystal diamond.