Zhibin Luo

Enhanced Charge Separation through ALD‐Modified Fe2O3/Fe2TiO5 Nanorod Heterojunction for Photoelectrochemical Water Oxidation

Hematite suffers from poor charge transport and separation properties for solar water splitting. This paper describes the design and fabrication of a 3D Fe2 O3 /Fe2 TiO5 heterojunction photoanode with improved charge separation, via a facile hydrothermal method followed by atomic layer deposition and air annealing. A highly crystallized Fe2 TiO5 phase forms with a distinct interface with the underlying Fe2 O3 core, where a 4 nm Fe2 TiO5 overlayer leads to the best photoelectrochemical performance. The favorable band offset between Fe2 O3 and Fe2 TiO5 establishes a type-II heterojunction at the Fe2 O3 /Fe2 TiO5 interface, which drives electron-hole separation effectively. The Fe2 O3 /Fe2 TiO5 composite electrode exhibits a dramatically improved photocurrent of 1.63 mA cm(-2) at 1.23 V versus reversible hydrogen electrode (RHE) under simulated 1 sun illumination (100 mW cm(-2) ), which is 3.5 times that of the bare Fe2 O3 electrode. Decorating the Fe2 O3 /Fe2 TiO5 heterojunction photoanode with earth-abundant FeNiOx cocatalyst further expedites surface reaction kinetics, leading to an onset potential of 0.8 V versus RHE with a photocurrent of 2.7 mA cm(-2) at 1.23 V and 4.6 mA cm(-2) at 1.6 V versus RHE. This sandwich photoanode shows an excellent stability for 5 h and achieves an overall Faradaic efficiency of 95% for O2 generation. This is the best performance ever reported for Fe2 O3 /Fe2 TiO5 photoanodes.

Dendritic Hematite Nanoarray Photoanode Modified with a Conformal Titanium Dioxide Interlayer for Effective Charge Collection

This paper describes the introduction of a thin titanium dioxide interlayer that serves as passivation layer and dopant source for hematite (α-Fe2 O3 ) nanoarray photoanodes. This interlayer is demonstrated to boost the photocurrent by suppressing the substrate/hematite interfacial charge recombination, and to increase the electrical conductivity by enabling Ti4+ incorporation. The dendritic nanostructure of this photoanode with an increased solid-liquid junction area further improves the surface charge collection efficiency, generating a photocurrent of about 2.5 mA cm-2 at 1.23 V versus the reversible hydrogen electrode (vs. RHE) under air mass 1.5G illumination. A photocurrent of approximately 3.1 mA cm-2 at 1.23 V vs. RHE could be achieved by addition of an iron oxide hydroxide cocatalyst.

Surviving High-Temperature Calcination: ZrO2-Induced Hematite Nanotubes for Photoelectrochemical Water Oxidation

Nanotubular Fe2 O3 is a promising photoanode material, and producing morphologies that withstand high-temperature calcination (HTC) is urgently needed to enhance the photoelectrochemical (PEC) performance. This work describes the design and fabrication of Fe2 O3 nanotube arrays that survive HTC for the first time. By introducing a ZrO2 shell on hydrothermal FeOOH nanorods by atomic layer deposition, subsequent high-temperature solid-state reaction converts FeOOH-ZrO2 nanorods to ZrO2 -induced Fe2 O3 nanotubes (Zr-Fe2 O3 NTs). The structural evolution of the hematite nanotubes is systematically explored. As a result of the nanostructuring and shortened charge collection distance, the nanotube photoanode shows a greatly improved PEC water oxidation activity, exhibiting a photocurrent density of 1.5 mA cm-2 at 1.23 V (vs. reversible hydrogen electrode, RHE), which is the highest among hematite nanotube photoanodes without co-catalysts. Furthermore, a Co-Pi decorated Zr-Fe2 O3 NT photoanode reveals an enhanced onset potential of 0.65 V (vs. RHE) and a photocurrent of 1.87 mA cm-2 (at 1.23 V vs. RHE).

Surface, Bulk, and Interface: Rational Design of Hematite Architecture toward Efficient Photo‐Electrochemical Water Splitting

Collecting and storing solar energy to hydrogen fuel through a photo-electrochemical (PEC) cell provides a clean and renewable pathway for future energy demands. Having earth-abundance, low biotoxicity, robustness, and an ideal n-type band position, hematite (α-Fe2 O3 ), the most common natural form of iron oxide, has occupied the research hotspot for decades. Here, a close look into recent progress of hematite photoanodes for PEC water splitting is provided. Effective approaches are introduced, such as cocatalysts loading and surface passivation layer deposition, to improve the hematite surface reaction in thermodynamics and kinetics. Second, typical methods for enhancing light absorption and accelerating charge transport in hematite bulk are reviewed, concentrating upon doping and nanostructuring. Third, the back contact between hematite and substrate, which affects interface states and electron transfer, is deliberated. In addition, perspectives on the key challenges and future prospects for the development of hematite photoelectrodes for PEC water splitting are given.

Low‐Coordinated Edge Sites on Ultrathin Palladium Nanosheets Boost Carbon Dioxide Electroreduction Performance

Electrochemical conversion of carbon dioxide (CO2 ) to value-added products is a possible way to decrease the problems resulting from CO2 emission. Thanks to the eminent conductivity and proper adsorption to intermediates, Pd has become a promising candidate for CO2 electroreduction (CO2 ER). However, Pd-based nanocatalysts generally need a large overpotential. Herein we describe that ultrathin Pd nanosheets effectively reduce the onset potential for CO by exposing abundant atoms with comparatively low generalized coordination number. Hexagonal Pd nanosheets with 5 atomic thickness and 5.1 nm edge length reached CO faradaic efficiency of 94 % at -0.5 V, without any decay after a stability test of 8 h. It appears to be the most efficient among all of Pd-based catalysts toward CO2 ER. Uniform hexagonal morphology made it reasonable to build models and take DFT calculations. The enhanced activity originates from mainly edge sites on palladium nanosheets.