A.I. Radu

Spacer geometry and particle deposition in spiral wound membrane feed channels

Deposition of microspheres mimicking bacterial cells was studied experimentally and with a numerical model in feed spacer membrane channels, as used in spiral wound nanofiltration (NF) and reverse osmosis (RO) membrane systems. In-situ microscopic observations in membrane fouling simulators revealed formation of specific particle deposition patterns for different diamond and ladder feed spacer orientations. A three-dimensional numerical model combining fluid flow with a Lagrangian approach for particle trajectory calculations could describe very well the in-situ observations on particle deposition in flow cells. Feed spacer geometry, positioning and cross-flow velocity sensitively influenced the particle transport and deposition patterns. The deposition patterns were not influenced by permeate production. This combined experimental-modeling approach could be used for feed spacer geometry optimization studies for reduced (bio)fouling.

New approaches to characterizing and understanding biofouling of spiral wound membrane systems

Historically, biofouling research on spiral wound membrane systems is typically problem solving oriented. Membrane modules are studied as black box systems, investigated by autopsies. Biofouling is not a simple process. Many factors influence each other in a non-linear fashion. These features make biofouling a subject which is not easy to study using a fundamental scientific approach. Nevertheless to solve or minimize the negative impacts of biofouling, a clear understanding of the interacting basic principles is needed. Recent research into microbiological characterizing of biofouling, small scale test units, application of in situ visualization methods, and model approaches allow such an integrated study of biofouling.

Combined biofouling and scaling in membrane feed channels: a new modeling approach

A mathematical model was developed for combined fouling due to biofilms and mineral precipitates in membrane feed channels with spacers. Finite element simulation of flow and solute transport in two-dimensional geometries was coupled with a particle-based approach for the development of a composite (cells and crystals) foulant layer. Three fouling scenarios were compared: biofouling only, scaling only and combined fouling. Combined fouling causes a quicker flux decline than the summed flux deterioration when scaling and biofouling act independently. The model results indicate that the presence of biofilms leads to more mineral formation due to: (1) an enhanced degree of saturation for salts next to the membrane and within the biofilm; and (2) more available surface for nucleation to occur. The impact of biofilm in accelerating gypsum precipitation depends on the composition of the feed water (eg the presence of NaCl) and the kinetics of crystal nucleation and growth. Interactions between flow, solute transport and biofilm-induced mineralization are discussed.

Experimental and numerical characterization of the water flow in spacer-filled channels of spiral-wound membranes

Micro-scale flow distribution in spacer-filled flow channels of spiral-wound membrane modules was determined with a particle image velocimetry system (PIV), aiming to elucidate the flow behaviour in spacer-filled flow channels. Two-dimensional water velocity fields were measured in a flow cell (representing the feed spacer-filled flow channel of a spiral wound reverse osmosis membrane module without permeate production) at several planes throughout the channel height. At linear flow velocities (volumetric flow rate per cross-section of the flow channel considering the channel porosity, also described as crossflow velocities) used in practice (0.074 and 0.163 m·s(-1)) the recorded flow was laminar with only slight unsteadiness in the upper velocity limit. At higher linear flow velocity (0.3 m·s(-1)) the flow was observed to be unsteady and with recirculation zones. Measurements made at different locations in the flow cell exhibited very similar flow patterns within all feed spacer mesh elements, thus revealing the same hydrodynamic conditions along the length of the flow channel. Three-dimensional (3-D) computational fluid dynamics simulations were performed using the same geometries and flow parameters as the experiments, based on steady laminar flow assumption. The numerical results were in good agreement (0.85-0.95 Bray-Curtis similarity) with the measured flow fields at linear velocities of 0.074 and 0.163 m·s(-1), thus supporting the use of model-based studies in the optimization of feed spacer geometries and operational conditions of spiral wound membrane systems.

Absorption of impinging water droplet in porous stones.

This paper presents an experimental investigation and numerical analysis of the absorption of water droplets impacting porous stones. The absorption process of an impinging droplet is here fully characterized from spreading to evaporation in terms of absorbed mass during droplet depletion and moisture content distribution in a time-resolved manner for three different natural stones. High-speed imaging and neutron radiography are used to quantify moisture absorption in porous stones of varying moisture properties from deposition until depletion. During impact and spreading, the droplet exhibits a dynamic non-wetting behavior. At maximum spreading, the droplet undergoes pinning, resulting into the contact radius remaining constant until droplet depletion. Absorption undergoes two phases: initially, absorption is hindered due a contact resistance attributed to entrapped air; afterwards, a more perfect capillary contact occurs and absorption goes on until depletion, concurrently with evaporation and further redistribution. A finite-element numerical model for isothermal unsaturated moisture transport in porous media captures the phases of mass absorption in good agreement with the experimental data. Droplet spreading and absorption are highly determined by the impact velocity of the droplet, while moisture content redistribution after depletion is much less dependent on impact conditions.

Development of a setup to enable stable and accurate flow conditions for membrane biofouling studies

AbstractSystematic laboratory studies on membrane biofouling require experimental conditions that are well defined and representative for practice. Hydrodynamics and flow rate variations affect biofilm formation, morphology, and detachment and impacts on membrane performance parameters such as feed channel pressure drop. There is a suite of available monitors to study biofouling, but systems to operate monitors have not been well designed to achieve an accurate, constant water flow required for a reliable determination of biomass accumulation and feed channel pressure drop increase. Studies were done with membrane fouling simulators operated in parallel with manual and automated flow control, with and without dosage of a biodegradable substrate to the feedwater to enhance biofouling rate. High flow rate variations were observed for the manual water flow system (up to ≈9%) compared to the automatic flow control system (<1%). The flow rate variation in the manual system was strongly increased by biofilm acc...

Recent advances in drying at interfaces of biomaterials

ABSTRACT A better insight in heat and mass transport across interfaces of biomaterials with their environment, particularly at the microscale, is a key element in improving dehydration processes. Recent advances in interfacial drying are targeted, including evaporation from microscopic pores, droplets or microperforated membranes, and drying of soft cellular tissue such as fruit. Manufacturing of thin biopolymer layers, such as (edible) films and coatings, is discussed as well as their performance as barriers at product–environment interfaces. The physical processes at play are illustrated, recent insights are highlighted and a future outlook is given. These interfacial processes are critical for controlling the processing conditions during drying and for tailoring the structure and quality of biomaterials.