A. Niemczewski

First results from Alcator-C-MOD

Early operation of the Alcator‐C‐MOD tokamak [I.H. Hutchinson, Proceedings of IEEE 13th Symposium on Fusion Engineering, Knoxville, TN, edited by M. Lubell, M. Nestor, and S. Vaughan (Institute of Electrical and Electronic Engineers, New York, 1990), Vol. 1, p. 13] is surveyed. Reliable operation, with plasma current up to 1 MA, has been obtained, despite the massive conducting superstructure and the associated error fields. However, vertical disruptions are not slowed by the long vessel time constant. With pellet fueling, peak densities up to 9×1020 m−3 have been attained and ‘‘snakes’’ are often seen. Initial characterization of divertor and scrape‐off layer is presented and indicates approximately Bohm diffusion. The edge plasma shows a wealth of marfe‐like phenomena, including a transition to detachment from the divertor plates with accompanying radiative divertor regions. Energy confinement generally appears to exceed the expectations of neo‐Alcator scaling. A transition to Ohmic H mode has been observed. Ion cyclotron heating experiments have demonstrated good power coupling, in agreement with theory.

Experimental investigation of transport phenomena in the scrape-off layer and divertor

Abstract Transport physics in the divertor and scrape-off layer of Alcator C-Mod is investigated for a wide range of plasma conditions. Parallel (∥) transport topics include: low recycling, high-recycling, and detached regimes, thermoelectric currents, asymmetric heat fluxes driven by thermoelectric currents, and reversed divertor flows. Perpendicular (⊥) transport topics include: expected and measured scalings of ⊥ gradients with local conditions, estimated χ⊥ profiles and scalings, divertor neutral retention effects, and L-mode/H-mode effects. Key results are: (i) classical ∥ transport is obeyed with ion-neutral momentum coupling effects, (ii) ⊥ heat transport is proportional to local gradients, (iii) χ⊥ αTe−0.6 n−0.6 L−0.7 in L-mode, insensitive to toroidal field, (iv) χ⊥ is dependent on divertor neutral retention, (v) H-mode transport barrier effects partially extend inside the SOL, (vi) inside/outside divertor asymmetries may be caused by a thermoelectric instability, and (vii) reversed ∥ flows depend on divertor asymmetries and their implicit ionization source imbalances.

Scaling and transport analysis of divertor conditions on the Alcator C-Mod tokamak

Detailed measurements and transport analysis of divertor conditions in Alcator C‐Mod [Phys. Plasmas 1, 1511 (1994)] are presented for a range of line‐averaged densities, 0.7<ne<2.2×1020 m−3. Three parallel heat transport regimes are evident in the scrape‐off layer: sheath‐limited conduction, high‐recycling divertor, and detached divertor, which can coexist in the same discharge. Local cross‐field pressure gradients are found to scale simply with a local electron temperature. This scaling is consistent with classical electron parallel conduction being balanced by anomalous cross‐field transport (χ⊥∼0.2 m2 s−1) proportional to the local pressure gradient. A 60%–80% of divertor power is radiated in attached discharges, approaching 100% in detached discharges. Detachment occurs when the heat flux to the plate is low and the plasma pressure is high (Te∼5 eV). High neutral pressures in the divertor are nearly always present (1–20 mTorr), sufficient to remove parallel momentum via ion–neutral collisions.

Dissipative divertor operation in the Alcator C-Mod tokamak

The achievement of large volumetric power losses (dissipation) in the Alcator C-Mod divertor region is demonstrated in two operational modes: radiative divertor and detached divertor. During radiative divertor operation, the fraction of SOL power lost by radiation is P R /P SOL 0.8 with single null plasmas, n e < 2 × 10 20 m −3 and I p < 1 MA. THESE PLASMAS SOMETIMES HAVE VERY HIGH RECYCLING, WITH N e, div ≤ 6 x 10 20 m −3 . As the divertor radiation and density increase, the plasma eventually detaches abruptly from the divertor plates: I SAT drops at the target and the divertor radiation peak moves to the X-point region. Probe measurements at the divertor plate show that the transition occurs when T e 5 eV. The critical n e for detachment depends linearly on the input power. This abrupt divertor detachment is preceded by a comparatively long period (∼ 1-200 ms) where a partial detachment is observed to grow at the outer divertor plate

Comparison of detached and radiative divertor operation in Alcator C-Mod

The divertor of the Alcator C‐Mod tokamak [Phys. Plasmas 1, 1511 (1994)] routinely radiates a large fraction of the power entering the scrape‐off layer. This dissipative divertor operation occurs whether the divertor is detached or not, and large volumetric radiative emissivities, up to 60 MW m−3 in ion cyclotron range of frequency (ICRF) heated discharges, have been measured using bolometer arrays. An analysis of both Ohmic and ICRF‐heated discharges has demonstrated some of the relative merits of detached divertor operation versus high‐recycling divertor operation. An advantage of detached divertor operation is that the power flux to the divertor plates is decreased even further than its already low value. Some disadvantages are that volumetric losses outside the separatrix in the divertor region are decreased, the neutral compression ratio is decreased, and the penetration efficiency of impurities increases.

Electron heating via mode converted ion Bernstein waves in the Alcator C-Mod tokamak

Highly localized direct electron heating [full width at half-maximum (FWHM)≅0.2a] via mode converted ion Bernstein waves has been observed in the Alcator C-Mod Tokamak [I. H. Hutchinson et al., Phys. Plasmas 1, 1511 (1994)]. Electron heating at or near the plasma center (r/a⩾0.3) has been observed in H(3He) discharges at B0=(6.0–6.5) T and ne(0)≅1.8×1020 m−3. [Here, the minority ion species is indicated parenthetically.] Off-axis heating (r/a⩾0.5) has also been observed in D(3He) plasmas at B0=7.9 T. The concentration of 3He in these experiments was in the range of n3He/ne≅(0.2–0.3) and the locations of the mode conversion layer and electron heating peak could be controlled by changing the 3He concentration or toroidal magnetic field (B0). The electron heating profiles were deduced using a rf modulation technique. Detailed comparisons with one-dimensional and toroidal full-wave models in the ion cyclotron range of frequencies have been carried out. One-dimensional full-wave code predictions were found to ...

Neutral particle dynamics in the Alcator C-Mod tokamak

An experimental study of neutral particle dynamics has been carried out over a wide range of operating conditions in the Alcator C Modified (Alcator C-Mod) tokamak using special purpose pressure gauges. Both divertor and midplane pressures are found to depend primarily on the edge plasma regimes defined by the scrape-off layer heat transport. While the maximum divertor neutral pressure (30-60 mtorr) is achieved at high core plasma densities (ne=(2-4)*1020 m-3), corresponding to the detached divertor state, the maximum ratio of divertor to midplane pressure (~70) is achieved in the high recycling transport regime. Variations in the divertor geometry have a weaker effect on the neutral pressures. For otherwise similar plasmas, the divertor pressure and compression are maximized when the strike point is located at the bottom of the vertical target plate. Modelling shows that the high pressure sustained during detached divertor operation (despite a considerable drop in the recycling source) can be explained by scattering of neutrals off the cold plasma plugging the divertor throat

Transport experiments in Alcator‐C‐Mod

A series of transport experiments has been carried out in Alcator‐C‐Mod. [Phys Plasmas 1, 1511 (1994)]. Data from both Ohmic and ICRF (ion cyclotron range of frequencies) heated plasmas can be fitted with an L‐mode (low mode) scaling law. The Ohmic τE’s show no scaling with density in any regime and can reach values of 2–3 times neo‐Alcator. Impurity confinement has been studied with the laser blow‐off technique with τI showing nearly linear scaling with plasma current. Ohmic and ICRF H modes are obtained over a wide range of discharge parameters, extending the range in the international database for nB, by almost a factor of 10. The power threshold for ELM‐free (edge localized mode) discharges is in rough agreement with the scaling P/S=0.044nB. Energy diffusivities of Ohmic and ICRF heated plasmas have been measured from local analysis of plasma profiles and power fluxes. The same analysis produces a value for plasma resistivity which lies between the Spitzer and neoclassical calculations. Analysis of pl...

Characteristics of high‐confinement modes in Alcator C Mod

The regime of high particle and energy confinement known as the H mode [Phys. Rev. Lett. 49, 1408 (1982)] has been extended to a unique range of operation for divertor tokamaks up to toroidal fields of nearly 8 T, line‐averaged electron densities of 3×1020 m−3, and surface power densities of nearly 0.6 MW/m2 in the compact high‐field tokamak Alcator C Mod [Phys. Plasmas 1, 1511 (1994)]. H modes are achieved in Alcator C Mod with Ion Cyclotron Resonant Frequency (ICRF) heating and with Ohmic heating alone without boronization of the all molybdenum tiled first wall. Large increases in charge exchange flux are observed during the H mode over the entire range of energies from 2 to 10 keV. There appears to be an upper limit to the midplane neutral pressure, of about 0.08 Pa above which no H modes have been observed. The plasmas with the best energy confinement have the lowest midplane neutral pressures, below 0.01 Pa. There is an edge electron temperature threshold such that Te≥280 eV ±40 eV for sustaining the...

H-modes on Alcator C-Mod

H-modes exhibiting improved confinement above the L-mode are achieved in Alcator C-Mod with ICRF and with ohmic heating alone without boronization. Both ELM-free and ELMy H-modes are obtained with total input power from 0.75 to 4.2 MW over a range of densities (0.8 to ) and toroidal fields (3 to 8 T). Type III ELMs are often observed to have coherent, high m and n precursor oscillations with frequencies of 100 - 160 kHz. The threshold power required to achieve the H-mode increases with density and toroidal field, in rough agreement with scalings derived from other tokamaks. The power densities and density times toroidal field products are an order of magnitude larger than in other tokamaks, in the range of values expected for ITER. The L - H and H - L transitions occur at approximately the same edge electron temperature. A low density limit to the H-mode is found at about . A high midplane neutral pressure limit of about 0.6 mTorr is also observed.