Adam L. Lubrano

Dynamic headspace generation and quantitation of triacetone triperoxide vapor.

Two methods for quantitation of triacetone triperoxide (TATP) vapor using a programmable temperature vaporization (PTV) inlet coupled to a gas chromatography/mass spectrometer (GC/MS) have been demonstrated. The dynamic headspace of bulk TATP was mixed with clean humid air to produce a TATP vapor stream. Sampling via a heated transfer line to a PTV inlet with a Tenax-TA™ filled liner allowed for direct injection of the vapor stream to a GC/MS for vapor quantitation. TATP was extracted from the vapor stream and subsequently desorbed from the PTV liner for splitless injection on the GC column. Calibration curves were prepared using solution standards with a standard split/splitless GC inlet for quantitation of the TATP vapor. Alternatively, vapor was sampled onto a Tenax-TA™ sample tube and placed into a thermal desorption system. In this instance, vapor was desorbed from the tube and subsequently trapped on a liquid nitrogen cooled PTV inlet. Calibration curves for this method were prepared from direct liquid injection of standards onto samples tube with the caveat that a vacuum is applied to the tube during deposition to ensure that the volatile TATP penetrates into the tube. Vapor concentration measurements, as determined by either GC/MS analysis or mass gravimetry of the bulk TATP, were statistically indistinguishable. Different approaches to broaden the TATP vapor dynamic range, including diluent air flow, sample chamber temperature, sample vial orifice size, and sample size are discussed. Vapor concentrations between 50 and 5400ngL(-1) are reported, with stable vapor generation observed for as long as 60 consecutive hours.

Characterization of thermal desorption instrumentation with a direct liquid deposition calibration method for trace 2,4,6-trinitrotoluene quantitation

The use of thermal desorption systems for the analysis of trace vapors typically requires establishing a calibration curve from vapors generated with a permeation tube. The slow equilibration time of permeation tubes causes such an approach to become laborious when covering a wide dynamic range. Furthermore, many analytes of interest, such as explosives, are not available as permeation tubes. A method for easily and effectively establishing calibration curves for explosive vapor samples via direct deposition of standard solutions on thermal desorption tubes was investigated. The various components of the thermal desorption system were compared to a standard split/splitless inlet. Calibration curves using the direct liquid deposition method with a thermal desorption unit coupled to a cryo-focusing inlet were compared to a standard split/splitless inlet, and a statistical difference was observed but does not eliminate or deter the use of the direct liquid deposition method for obtaining quantitative results for explosive vapors.

Direct liquid deposition calibration method for trace cyclotrimethylenetrinitramine using thermal desorption instrumentation.

A simple method for establishing calibration curves with sorbent-filled thermal desorption tubes has been demonstrated for nitroaromatic and nitramine vapor samples using a thermal desorption system with a cooled inlet system (TDS-CIS), which was coupled to a gas chromatograph (GC) with an electron capture detector (ECD). The method relies upon the direct liquid deposition of standard solutions onto the glass frit at the head of sorbent-filled thermal desorption tubes. Linear calibration results and ideal system conditions for the TDS-CIS-GC-ECD were established for mixtures containing both cyclotrimethylenetrinitramine, a.k.a. RDX, and 2,4,6-trinitrotoluene (TNT). Because of the chemical characteristics of RDX, a higher TDS-CIS flow rate relative to the optimized approach for TNT was required for efficient RDX desorption. Simultaneous quantitation of TNT and RDX using the direct liquid deposition method with optimized instrumentation parameters for RDX were compared to results from a standard split/splitless GC inlet and a CIS.

Trace Explosives Vapor Generation and Quantitation at Parts per Quadrillion Concentrations

The generation of trace 2,4,6-trinitrotoluene (TNT), cyclotrimethylenetrinitramine (RDX), and pentaerythritol tetranitrate (PETN) vapors using a pneumatically modulated liquid delivery system (PMLDS) coupled to a polytetrafluoroethylene (PTFE) total-consumption micronebulizer is presented. The vapor generator operates in a continuous manner with final vapor concentrations proportional to the explosive concentration in aqueous solution delivered through the nebulizer and the diluent air flow rate. For quantitation of concentrations in the parts per billionvolume (ppbv) to parts per trillionvolume (pptrv) range, Tenax-TA thermal desorption tubes were used for vapor collection with subsequent analysis on a thermal-desorption system programmable-temperature vaporization gas chromatograph (TDS-PTV-GC) with a μ-ECD detector. With 30 min sample times and an average sampling rate of 100 mL min(-1), vapor concentrations of 38 pptrv for TNT, 25 pptrv for RDX, and 26 pptrv for PETN were determined. For parts per quadrillionvolume (ppqv) vapor quantitation of TNT and RDX, an online PTV-GC system with a negative-ion chemical ionization mass spectrometer (methane reagent gas) was used for direct sampling and capture of the vapor on the PTV inlet. Vapor concentrations as low as 160 ppqv and 710 ppqv for TNT and RDX were quantified, respectively, with an instrument duty cycle as low as 4 min.

Minimizing thermal degradation in gas chromatographic quantitation of pentaerythritol tetranitrate

An analytical method for establishing calibration curves for the quantitation of pentaerythriol tetranitrate (PETN) from sorbent-filled thermal desorption tubes by gas chromatography with electron capture detection (TDS-GC-ECD) was developed. As PETN has been demonstrated to thermally degrade under typical GC instrument conditions, peaks corresponding to both PETN degradants and molecular PETN are observed. The retention time corresponding to intact PETN was verified by high-resolution mass spectrometry with a flowing atmospheric pressure afterglow (FAPA) ionization source, which enabled soft ionization of intact PETN eluting the GC and subsequent accurate-mass identification. The GC separation parameters were transferred to a conventional GC-ECD instrument where analytical method-induced PETN degradation was further characterized and minimized. A method calibration curve was established by direct liquid deposition of PETN standard solutions onto the glass frit at the head of sorbent-filled thermal desorption tubes. Two local, linear relationships between detector response and PETN concentration were observed, with a total dynamic range of 0.25-25ng.

Trace explosives sensor testbed (TESTbed)

A novel vapor delivery testbed, referred to as the Trace Explosives Sensor Testbed, or TESTbed, is demonstrated that is amenable to both high- and low-volatility explosives vapors including nitromethane, nitroglycerine, ethylene glycol dinitrate, triacetone triperoxide, 2,4,6-trinitrotoluene, pentaerythritol tetranitrate, and hexahydro-1,3,5-trinitro-1,3,5-triazine. The TESTbed incorporates a six-port dual-line manifold system allowing for rapid actuation between a dedicated clean air source and a trace explosives vapor source. Explosives and explosives-related vapors can be sourced through a number of means including gas cylinders, permeation tube ovens, dynamic headspace chambers, and a Pneumatically Modulated Liquid Delivery System coupled to a perfluoroalkoxy total-consumption microflow nebulizer. Key features of the TESTbed include continuous and pulseless control of trace vapor concentrations with wide dynamic range of concentration generation, six sampling ports with reproducible vapor profile outputs, limited low-volatility explosives adsorption to the manifold surface, temperature and humidity control of the vapor stream, and a graphical user interface for system operation and testing protocol implementation.

Analysis of ammonium nitrate headspace by on-fiber solid phase microextraction derivatization with gas chromatography mass spectrometry

A novel analytical method has been developed for the quantitation of trace levels of ammonia in the headspace of ammonium nitrate (AN) using derivatized solid phase microextraction (SPME) fibers with gas chromatography mass spectrometry (GC-MS). Ammonia is difficult to detect via direct injection into a GC-MS because of its low molecular weight and extreme polarity. To circumvent this issue, ammonia was derivatized directly onto a SPME fiber by the reaction of butyl chloroformate coated fibers with the ammonia to form butyl carbamate. A derivatized externally sampled internal standard (dESIS) method based upon the reactivity of diethylamine with unreacted butyl chloroformate on the SPME fiber to form butyl diethylcarbamate was established for the reproducible quantification of ammonia concentration. Both of these compounds are easily detectable and separable via GC-MS. The optimized method was then used to quantitate the vapor concentration of ammonia in the headspace of two commonly used improvised explosive device (IED) materials, ammonium nitrate fuel oil (ANFO) and ammonium nitrate aluminum powder (Ammonal), as well as identify the presence of additional fuel components within the headspace.

Quantitative detection of trace explosive vapors by programmed temperature desorption gas chromatography-electron capture detector.

The direct liquid deposition of solution standards onto sorbent-filled thermal desorption tubes is used for the quantitative analysis of trace explosive vapor samples. The direct liquid deposition method yields a higher fidelity between the analysis of vapor samples and the analysis of solution standards than using separate injection methods for vapors and solutions, i.e., samples collected on vapor collection tubes and standards prepared in solution vials. Additionally, the method can account for instrumentation losses, which makes it ideal for minimizing variability and quantitative trace chemical detection. Gas chromatography with an electron capture detector is an instrumentation configuration sensitive to nitro-energetics, such as TNT and RDX, due to their relatively high electron affinity. However, vapor quantitation of these compounds is difficult without viable vapor standards. Thus, we eliminate the requirement for vapor standards by combining the sensitivity of the instrumentation with a direct liquid deposition protocol to analyze trace explosive vapor samples.

Note: Pneumatically modulated liquid delivery with feedback control

We present the design and characterization of a pneumatically driven liquid delivery system using an embedded microcontroller with feedback control capable of maintaining a stable, constant flow rate over several hours of operation. Flow rates with relative standard deviations less than 1% were achieved and compared to a typical laboratory syringe pump.