Braden C. Giordano

On-line sample pre-concentration in microfluidic devices: a review.

On-line sample preconcentration is an essential tool in the development of microfluidic-based separation platforms. In order to become more competitive with traditional separation techniques, the community must continue to develop newer and more novel methods to improve detection limits, remove unwanted sample matrix components that disrupt separation performance, and enrich/purify analytes for other chip-based actions. Our goal in this review is to familiarize the reader with many of the options available for on-chip concentration enhancement with a focus on those manuscripts that, in our assessment, best describe the fundamental principles that govern those enhancements. Sections discussing both electrophoretic and nonelectrophoretic modes of preconcentration are included with a focus on device design and mechanisms of preconcentration. This review is not meant to be a comprehensive collection of every available example, but our hope is that by learning how on-line sample concentration techniques are being applied today, the reader will be inspired to apply these techniques to further enhance their own programs.

Dynamic headspace generation and quantitation of triacetone triperoxide vapor.

Two methods for quantitation of triacetone triperoxide (TATP) vapor using a programmable temperature vaporization (PTV) inlet coupled to a gas chromatography/mass spectrometer (GC/MS) have been demonstrated. The dynamic headspace of bulk TATP was mixed with clean humid air to produce a TATP vapor stream. Sampling via a heated transfer line to a PTV inlet with a Tenax-TA™ filled liner allowed for direct injection of the vapor stream to a GC/MS for vapor quantitation. TATP was extracted from the vapor stream and subsequently desorbed from the PTV liner for splitless injection on the GC column. Calibration curves were prepared using solution standards with a standard split/splitless GC inlet for quantitation of the TATP vapor. Alternatively, vapor was sampled onto a Tenax-TA™ sample tube and placed into a thermal desorption system. In this instance, vapor was desorbed from the tube and subsequently trapped on a liquid nitrogen cooled PTV inlet. Calibration curves for this method were prepared from direct liquid injection of standards onto samples tube with the caveat that a vacuum is applied to the tube during deposition to ensure that the volatile TATP penetrates into the tube. Vapor concentration measurements, as determined by either GC/MS analysis or mass gravimetry of the bulk TATP, were statistically indistinguishable. Different approaches to broaden the TATP vapor dynamic range, including diluent air flow, sample chamber temperature, sample vial orifice size, and sample size are discussed. Vapor concentrations between 50 and 5400ngL(-1) are reported, with stable vapor generation observed for as long as 60 consecutive hours.

Characterization of thermal desorption instrumentation with a direct liquid deposition calibration method for trace 2,4,6-trinitrotoluene quantitation

The use of thermal desorption systems for the analysis of trace vapors typically requires establishing a calibration curve from vapors generated with a permeation tube. The slow equilibration time of permeation tubes causes such an approach to become laborious when covering a wide dynamic range. Furthermore, many analytes of interest, such as explosives, are not available as permeation tubes. A method for easily and effectively establishing calibration curves for explosive vapor samples via direct deposition of standard solutions on thermal desorption tubes was investigated. The various components of the thermal desorption system were compared to a standard split/splitless inlet. Calibration curves using the direct liquid deposition method with a thermal desorption unit coupled to a cryo-focusing inlet were compared to a standard split/splitless inlet, and a statistical difference was observed but does not eliminate or deter the use of the direct liquid deposition method for obtaining quantitative results for explosive vapors.

Direct liquid deposition calibration method for trace cyclotrimethylenetrinitramine using thermal desorption instrumentation.

A simple method for establishing calibration curves with sorbent-filled thermal desorption tubes has been demonstrated for nitroaromatic and nitramine vapor samples using a thermal desorption system with a cooled inlet system (TDS-CIS), which was coupled to a gas chromatograph (GC) with an electron capture detector (ECD). The method relies upon the direct liquid deposition of standard solutions onto the glass frit at the head of sorbent-filled thermal desorption tubes. Linear calibration results and ideal system conditions for the TDS-CIS-GC-ECD were established for mixtures containing both cyclotrimethylenetrinitramine, a.k.a. RDX, and 2,4,6-trinitrotoluene (TNT). Because of the chemical characteristics of RDX, a higher TDS-CIS flow rate relative to the optimized approach for TNT was required for efficient RDX desorption. Simultaneous quantitation of TNT and RDX using the direct liquid deposition method with optimized instrumentation parameters for RDX were compared to results from a standard split/splitless GC inlet and a CIS.

Direct injection of seawater for the analysis of nitroaromatic explosives and their degradation products by micellar electrokinetic chromatography.

Practical considerations for the injection and separation of nitroaromatic explosives in seawater sample matrices are discussed. The use of high surfactant concentrations and long electrokinetic injections allows for improved detection limits. Sensitivity was enhanced by two mechanisms, improved stacking at the detector-side of the sample plug and desorption of analyte from the capillary wall by surfactant-containing BGE from the inlet side of the sample plug. Calculated limits of detection (S/N=3) for analytes prepared in pure seawater were 70-800 ppb with injection times varying from 5 to 100 s.

Minimizing thermal degradation in gas chromatographic quantitation of pentaerythritol tetranitrate

An analytical method for establishing calibration curves for the quantitation of pentaerythriol tetranitrate (PETN) from sorbent-filled thermal desorption tubes by gas chromatography with electron capture detection (TDS-GC-ECD) was developed. As PETN has been demonstrated to thermally degrade under typical GC instrument conditions, peaks corresponding to both PETN degradants and molecular PETN are observed. The retention time corresponding to intact PETN was verified by high-resolution mass spectrometry with a flowing atmospheric pressure afterglow (FAPA) ionization source, which enabled soft ionization of intact PETN eluting the GC and subsequent accurate-mass identification. The GC separation parameters were transferred to a conventional GC-ECD instrument where analytical method-induced PETN degradation was further characterized and minimized. A method calibration curve was established by direct liquid deposition of PETN standard solutions onto the glass frit at the head of sorbent-filled thermal desorption tubes. Two local, linear relationships between detector response and PETN concentration were observed, with a total dynamic range of 0.25-25ng.

Isobutane Made Practical as a Reagent Gas for Chemical Ionization Mass Spectrometry

AbstractAs a reagent gas for positive- and negative-mode chemical ionization mass spectrometry (CI-MS), isobutane (i-C4H10) produces superior analyte signal abundance to methane. Isobutane has never been widely adopted for CI-MS because it fouls the ion source more rapidly and produces positive CI spectra that are more strongly dependent on reagent gas pressure compared with methane. Isobutane was diluted to various concentrations in argon for use as a reagent gas with an unmodified commercial gas chromatograph-mass spectrometer. Analyte spectra were directly compared using methane, isobutane, and isobutane/argon mixtures. A mixture of 10% i-C4H10 in argon produced twice the positive-mode analyte signal of methane, equal to pure isobutane, and reduced spectral dependence on reagent gas pressure. Electron capture negative chemical ionization using 1% i-C4H10 in argon tripled analyte signal compared with methane and was reproducible, unlike pure isobutane. The operative lifetime of the ion source using isobutane/argon mixtures was extended exponentially compared with pure isobutane, producing stable and reproducible CI signal throughout. By diluting the reagent gas in an inert buffer gas, isobutane CI-MS experiments were made as practical to use as methane CI-MS experiments but with superior analytical performance. Graphical Abstractᅟ

Quantitative detection of trace explosive vapors by programmed temperature desorption gas chromatography-electron capture detector.

The direct liquid deposition of solution standards onto sorbent-filled thermal desorption tubes is used for the quantitative analysis of trace explosive vapor samples. The direct liquid deposition method yields a higher fidelity between the analysis of vapor samples and the analysis of solution standards than using separate injection methods for vapors and solutions, i.e., samples collected on vapor collection tubes and standards prepared in solution vials. Additionally, the method can account for instrumentation losses, which makes it ideal for minimizing variability and quantitative trace chemical detection. Gas chromatography with an electron capture detector is an instrumentation configuration sensitive to nitro-energetics, such as TNT and RDX, due to their relatively high electron affinity. However, vapor quantitation of these compounds is difficult without viable vapor standards. Thus, we eliminate the requirement for vapor standards by combining the sensitivity of the instrumentation with a direct liquid deposition protocol to analyze trace explosive vapor samples.

Lab on a Chip Sensor Platform for Explosives and CBW Toxin Detection

There has been significant interest in the adaptation of lab on a chip devices for the separation and detection of chemical and biological toxins. Potential toxic and/or hazardous analytes of concern in our program include BWA protein toxins, e.g., SEB and ricin, ingestible CW toxins, e.g. alkaloids and rat poisons, and nitroaromatic explosives indicative of IEDs. Discussion will center around our efforts to enhance sensitivity and selectivity on a microchip by incorporation of micro-solid-phase extraction, microchip bubble-cell long pathlength UV detection, organically-modified sol-gel materials for electrochromatography, protein recognition aptamers, and microfluidic-based displacement immunoassays.

Mixed Vapor Generation Device for delivery of homemade explosives vapor plumes

While there is a large body of research on the properties and detection of traditional military high explosives and propellant low explosives, there is a dearth of research on homemade explosive (HME) materials, though they are prevalent today. The safety of working with these materials in the laboratory is the greatest limiting factor preventing HME research. A vapor delivery tool, the Mixed Vapor Generation Device (MV-Gen), was designed to safely contain the individual solid or liquid components that often compose homemade explosives vapor plumes and deliver the mixed component vapors for instrumental sampling and analysis. Within the MV-Gen, each component is separated and only the vapors mix as they are carried through the device by flowing air. The resulting mixed vapor is representative of either mixed explosive material or bulk explosives. Component materials are held in up to four individual, removable vials with vapor concentrations controlled by vial orifice size, temperature, and diluent airflow. The total concentration can be adjusted by altering vial temperature via a thermal water jacket surrounding the entirety of the device, or by adjusting the flow rate of diluent air through the device. The MV-Gen was evaluated first with surrogate compounds, followed by two types of homemade explosives, to include a binary explosive mixture and a peroxide explosive. To evaluate the device, vapors were cold-trapped on an online sampling system and analyzed by gas chromatography/mass spectrometry. It was determined that the device yielded reproducible vapor concentrations of both single and mixed components, and the ratio of these vapors can be easily adjusted to mimic varying forms of homemade explosives.