Agnes Parr

Improving the thermal stability of 1-3 piezoelectric composite transducers

The effect of temperature on the behavior of 1-3 piezoelectric composites manufactured using various polymeric materials was assessed experimentally through electrical impedance analysis and laser vibrometry. Device behavior varied with temperature irrespective of the polymer filler. Most significant changes in the piezoelectric composites were recorded around the glass transition temperature (T/sub g/) of the polymer; movement to lower fundamental resonant frequencies and higher values of electrical impedance minima were observed at higher temperatures. Decoupling of the pillars from the polymer matrix was observed by laser vibrometry at high temperatures. The use of high T/sub g/ polymer extended the operational temperature range of a piezoelectric composite, and a high T/sub g/ polymer with improved thermal conductivity also proved beneficial. For all devices, at temperatures very close to room temperature, subtle changes in device performance, linked to polymer softening were observed. Particulate-filled materials have been investigated, and it is recognized that the high viscosities and low mechanical damping of such materials could be problematic for piezoelectric composite manufacture. The thermal solver of the PZFlex finite element code has been used to predict the temporal and spatial temperature response of a selection of the devices presented. The simulated and experimental data compare favorably.

Experimental and theoretical evaluation of the thermal behaviour of 1-3 piezoelectric composite transducers

This paper describes progress towards the understanding of temperature effects in 1-3 piezoelectric composite transducers, carried out via a combination of experimental investigation and finite element (FE) analysis using the commercially available PZFlex code. The elastic properties and internal absorption of different passive materials are measured using a through transmission ultrasonic technique, with dynamic mechanical thermal analysis and differential scanning calorimetry being employed to evaluate the glass transition behaviour and specific heat capacities, respectively. The fillers are then incorporated into piezoelectric composite devices and the transducer performance measured over a wide temperature range by means of electrical impedance analysis and laser scanning of the active surface. The FE models are employed to predict the temperature distribution within such transducers as a function of constituent material properties and the data is correlated with the experimentally measured characteristics. The influence of glass transition temperature on viscoelastic properties is highlighted, along with the design compromises necessary to ensure effective high power performance.

Investigating the thermal stability of 1-3 piezoelectric composite transducers by varying the thermal conductivity and glass transition temperature of the polymeric filler material

The thermal behaviour of a number of 1-3 piezoelectric composite transducers is discussed. In particular, devices manufactured from a polymer filler with a relatively high glass to rubber transition temperature (T/sub g/), and from polymer systems with increased thermal conductivity, are evaluated. The mechanical properties of the various filler materials were obtained via ultrasonic measurements, with the thermal properties extracted using dynamic mechanical thermal analysis (dmta), differential scanning calorimetry (dsc) and laserflash studies. A range of ultrasonic transducers were then constructed and their thermal stability studied using a combination of impedance analysis and laser surface displacement measurement.

Performance of periodic piezoelectric composite arrays incorporating a passive phase exhibiting anisotropic properties

This paper explores the minimisation of interelement cross talk in 1-D and 2-D periodic composite array structures through the incorporation of a passive phase exhibiting anisotropic elastic properties. Initially the PZFlex finite element code was used to monitor array aperture response as a function of material properties. It is shown that in array structures comprising passive polymer materials possessing low longitudinal loss and high shear loss, inter-element mechanical cross talk is reduced, without a concomitant reduction in element sensitivity. A number of polymer materials with the desired properties were synthesised and their elastic character confirmed through a program of materials characterisation. Finally, a range of experimental devices exhibiting improved directional response, as a result of a significant reduction in interelement cross talk, are presented and the predicted array characteristics are shown to compare favourably in each case.

Multilayered piezoelectric composite transducers

Multilayered piezoelectric materials present themselves as a suitable technology for the development of sub 100kHz transducers. A variety of different configurations have been proposed, including stacked 2-2, 1-3 and 3-1 connectivity configurations. Historically multilayer devices designed for low frequency of operation have comprised uniform layer thickness through the height of the device. The potential for extended bandwidth through the use of non-uniform layers through the thickness dimension has been investigated. In addition commercially available stacked ceramic mechanical actuators have been investigated. A combination of theoretical and experimental assessment has been employed to evaluate each transducer technology. Selection of the passive phase for these multilayer devices is critical. Typically, these devices operate in the high power regime and as such selection of the passive polymer material is crucial - thermal stability coupled with thermal conductivity would be a virtue. To this end a number of polymer materials possessing the appropriate thermal properties have been investigated.

Improving the thermal stability of 1-3 piezoelectric composite transducers manufactured using thermally conductive polymeric fillers

With a view to improving the thermal stability of ultrasonic transducers prepared using 1-3 piezoelectric composites, the use of front face layers manufactured from thermally insulating and partially thermally conductive polymeric materials has been investigated. Experimentally, heat dissipation was investigated, in air and in water, using different transducer configurations and the advantage of including a front face layer manufactured from thermally conductive polymeric material is demonstrated. The PZFlex finite element modelling package was utilised to assess the thermal diffusivity of each polymer in the different transducer configurations and was found to compare well with experiment.

P2O-3 Experimental Assessment of Periodic Piezoelectric Composite Arrays Incorporating an Anisotropic Passive Phase

This paper discusses the experimental assessment of a number of piezoelectric composite array structures incorporating a novel passive phase exhibiting anisotropic elastic properties. The passive polymer phase has been designed to limit inter-element crosstalk by attenuating lateral propagation across the array aperture. A selection of water coupled linear array coupons, operating with a nominal 400 kHz fundamental thickness mode frequency, has been prepared comprising the novel anisotropic passive phase. As a control, comparisons are made to similarly configured devices employing isotropic filler materials. Scanning laser vibrometry and measurements of electrical impedance characteristic on the array substrate demonstrate that the fundamental thickness mode of the devices configured with anisotropic polymer fillers is not contaminated by parasitic modes of vibration. The reasons for this are explained by considering the dispersion characteristics of the substrate. Water coupled hydrophone measurements of array element directivity; transmit voltage response and subsequently efficiency calculations illustrate that the observed reduction in mechanical cross talk has not been achieved at the expense of element sensitivity. Finally, comparisons between the experimental data and the PZFlex derived array responses are made, with good corroboration demonstrated