Alexandre Troge

Tapered transmission line technique based graded matching layers for thickness mode piezoelectric transducers

Conventionally, in order to acoustically match thickness mode piezoelectric transducers to a low acoustic impedance load medium, multiple quarter wavelength (QW) matching layers are employed at the front face of the device. Typically a number of layers, 2–4 in number, are employed resulting in discrete impedance steps within the acoustic matching scheme. This can result in impedance matching with limited bandwidth characteristics. This paper investigates the application of tapered transmission line filter theory to implement a graded impedance profile, through the thickness of the matching layer scheme, to solve the impedance mismatch problem whilst accounting for enhanced transducer sensitivity and bandwidth.

Performance of periodic piezoelectric composite arrays incorporating a passive phase exhibiting anisotropic properties

This paper explores the minimisation of interelement cross talk in 1-D and 2-D periodic composite array structures through the incorporation of a passive phase exhibiting anisotropic elastic properties. Initially the PZFlex finite element code was used to monitor array aperture response as a function of material properties. It is shown that in array structures comprising passive polymer materials possessing low longitudinal loss and high shear loss, inter-element mechanical cross talk is reduced, without a concomitant reduction in element sensitivity. A number of polymer materials with the desired properties were synthesised and their elastic character confirmed through a program of materials characterisation. Finally, a range of experimental devices exhibiting improved directional response, as a result of a significant reduction in interelement cross talk, are presented and the predicted array characteristics are shown to compare favourably in each case.

Properties of photocured epoxy resin materials for application in piezoelectric ultrasonic transducer matching layers.

This paper describes the acoustic properties of a range of epoxy resins prepared by photocuring that are suitable for application in piezoelectric ultrasonic transducer matching layers. Materials, based on blends of diglycidyl ether of Bisphenol A and 1,4-cyclohexanedimethanol diglycidyl ether, are described. Furthermore, in order to vary the elastic character of the base resin, samples containing polymer microspheres or barium sulfate particles are also described. The acoustic properties of the materials are determined by a liquid coupled through transmission methodology, capable of determining the velocity and attenuation of longitudinal and shear waves propagating in an isotropic layer. Measured acoustic properties are reported which demonstrate materials with specific acoustic impedance varying in the range 0.88-6.25 MRayls. In the samples comprising blends of resin types, a linear variation in the acoustic velocities and density was observed. In the barium sulfate filled samples, acoustic impedance showed an approximately linear variation with composition, reflecting the dominance of the density variation. While such variations can be predicted by simple mixing laws, relaxation and scattering effects influence the attenuation in both the blended and filled resins. These phenomena are discussed with reference to dynamic mechanical thermal analysis and differential scanning calorimetry of the samples.

P2O-1 A Three-Port Acoustic Lattice Model for Piezoelectric Transducers Containing Opposing Zones of Polarization

Inversion Layer Transducers (ILT) have attracted considerable interest in the recent past, due to the wide bandwidth and even harmonic sensitivity. This paper presents a new three-port lattice model for ILT devices. Based on linear systems theory, a discrete bi-directional lattice is used to describe the mechanical wave propagation and continuous transfer function to represent the electrical parameter. The mathematical formulation for an ILT configuration, and a straightforward physical interpretation of the lattice model is presented. A selection of experimental and simulation results are included to demonstrate the feasibility of the technique

P2O-3 Experimental Assessment of Periodic Piezoelectric Composite Arrays Incorporating an Anisotropic Passive Phase

This paper discusses the experimental assessment of a number of piezoelectric composite array structures incorporating a novel passive phase exhibiting anisotropic elastic properties. The passive polymer phase has been designed to limit inter-element crosstalk by attenuating lateral propagation across the array aperture. A selection of water coupled linear array coupons, operating with a nominal 400 kHz fundamental thickness mode frequency, has been prepared comprising the novel anisotropic passive phase. As a control, comparisons are made to similarly configured devices employing isotropic filler materials. Scanning laser vibrometry and measurements of electrical impedance characteristic on the array substrate demonstrate that the fundamental thickness mode of the devices configured with anisotropic polymer fillers is not contaminated by parasitic modes of vibration. The reasons for this are explained by considering the dispersion characteristics of the substrate. Water coupled hydrophone measurements of array element directivity; transmit voltage response and subsequently efficiency calculations illustrate that the observed reduction in mechanical cross talk has not been achieved at the expense of element sensitivity. Finally, comparisons between the experimental data and the PZFlex derived array responses are made, with good corroboration demonstrated