Akiko Haruyama

Influence of Finishing/Polishing Procedures on the Surface Texture of Two Resin Composites

This study compared surface roughness and gloss produced by different finishing/polishing procedures for two resin composites, Clearfil AP-X (AP-X) and Estelite Σ (ES). A total of 70 composite discs (n=35 for each resin composite) were prepared and divided at random into seven finishing/polishing groups (n=5): glass-pressed control; using a super-fine-grit diamond bur (SF); using CompoMaster (CM) after SF-finishing (SF+CM); using White Point (WP) after SF-finishing (SF+WP); using CM after SF+WP-finishing (SF+WP+CM); using Stainbuster (SB) after SF-finishing (SF+SB); and using CM after SF+SB-finishing (SF+SB+CM). After the finishing/polishing procedures, average surface roughness (Ra) and surface gloss (Gs(60°)) of all specimens were assessed with a surface profilometer and specimen gloss meter, respectively. Glass-pressed controls for both AP-X and ES composites showed the best surface finish in terms of both Ra and Gs(60°). SF-finishing produced the roughest surface and led to almost complete loss of gloss. While additional polishing with CM reduced Ra and increased Gs(60°), the additional finishing effect of WP or SB between SF-finishing and CM-polishing was not found for either AP-X or ES.

Effect of Emitted Wavelength and Light Guide Type on Irradiance Discrepancies in Hand-Held Dental Curing Radiometers

The purpose of this study was to determine any discrepancies in the outputs of five commercial dental radiometers and also to evaluate the accuracy of these devices using a laboratory-grade spectroradiometer. The power densities of 12 different curing light sources were repeatedly measured for a total of five times using each radiometer in a random order. The emission spectra of all of the curing light sources were also measured using the spectroradiometer, and the integral value of each spectrum was calculated to determine the genuine power densities, which were then compared to the displayed power densities measured by the dental radiometers. The displayed values of power density were various and were dependent on the brand of radiometer, and this may be because each radiometer has a different wavelength sensitivity. These results cast doubt upon the accuracy of commercially available dental radiometers.

Light-curing of dental resins with GaN violet laser diode: The effect of photoinitiator on mechanical strength

The purpose of this study was to evaluate whether a Gallium Nitride (GaN) -based violet laser diode (VLM500) could be used as a light source for light-cured dental resins. Three experimental unfilled resins containing different photoinitiators (camphorquinone, CQ; phenyl propanedione, PPD; or mono acylphosphineoxide, MAPO) were evaluated. These resins were light-cured with a VLM500 laser diode, and their ultimate micro-tensile strengths (μTS) were compared to those cured with three different LED light sources (Curenos, G-Light Prima-normal mode and G-Light Prima-PL mode). The VLM500 produced high μTS values in all three resins, and we concluded that this violet laser diode can be used as a light source for light-cured dental resin materials.

Influence of hydrophilic pre-treatment on resin bonding to zirconia ceramics.

Atmospheric plasma or ultraviolet (UV) treatment alters the surface characteristics of tetragonal zirconia polycrystal (TZP), increasing its hydrophilicity by reducing the contact angle against water to zero. This suggests that such treatment would increase the wettability of bonding resin. The purpose of this study was to determine how increasing the hydrophilicity of TZP through plasma irradiation, UV treatment, or application of ceramic primer affected initial bonding with resin composites. Here, the effect of each pre-treatment on the hydrophilicity of TZP surfaces was determined by evaluating change in shear bond strength. Plasma irradiation, UV, or ceramic primer pre-treatment showed no significant effect on bonding strength between TZP surfaces and resin composites. In addition, alumina blasting yielded no significant increase in bond strength. Plasma irradiation, UV treatment, or ceramic primer pre-treatment did not lead to significant increase in bond strength between TZP and resin composites.

Light-curing efficiency of dental adhesives by gallium nitride violet-laser diode determined in terms of ultimate micro-tensile strength

The purpose of this study was to evaluate whether violet-laser diode (VLD) can be used as light-curing source. The ultimate (micro-)tensile strength (μTS) of three adhesives was determined when cured by VLD in comparison with curing by two different types of commercial LED light-curing units. One VLD (VLM 500) and two LED units (Curenos and G-Light Prima) were used to cure the adhesive resin of the two-step self-etch adhesives Clearfil SE Bond, Tokuso Mac Bond II, and FL-Bond II. A 0.6-mm thick acrylic mould was filled with adhesive resin and cured for 60 s. After 24-h water storage, specimens were trimmed into an hourglass shape with a width of 1.2 mm at the narrowest part, after which the μTS was determined (n=10). In addition, the light transmittance of each adhesive was characterized using a UV-vis-NIR spectrometer. No significant difference in curing efficiency between VLD and LED were observed for both Tokuso Mac Bond II and FL-Bond II (p>0.05). For Clearfil SE Bond, the μTS of VLD-cured specimens was higher than that of the specimens cured by the LED Curenos unit (p<0.05). Spectrometry revealed that this marked difference must be attributed to a different light transmittance of Clearfil SE Bond for visible blue light versus for the lower area of UV and visible violet light. In conclusion, A GaN-based violet laser diode can be used as light-curing source to initiate polymerization of dental resins.

Effect of titanium dioxide and 3.5% hydrogen peroxide with 405-nm diode laser irradiation on bonding of resin to pulp chamber dentin

This study was conducted to determine the effect of a 3.5% hydrogen peroxide solution containing titanium dioxide on bonding of resin to pulp chamber dentin. Extracted bovine anterior teeth were allocated to three groups of ten teeth each. The coronal labial pulp chamber dentin was exposed and bleached with 3.5% hydrogen peroxide with titanium dioxide with 405-nm diode laser irradiation for 15 min (Group 1); 30% hydrogen peroxide with halogen lamp irradiation for 15 min (Group 2); and distilled water for 15 min (Group 3). After bleaching, the pulp chamber dentin was prepared for composite resin bonding and the interface between the resin and dentin was observed by scanning electron microscopy. The microtensile bond strength (μTBS) and failure patterns were determined. The μTBS values (mean ± SD) were: 17.28 ± 5.79 MPa (n = 36), 0 MPa, and 26.50 ± 9.83 MPa (n = 36) in Groups 1, 2, and 3, respectively. The μTBS in Group 3 was significantly higher than that in Group 1 (P < 0.05). Hybrid layers and resin tags were clearly observed at the interface in Groups 1 and 3, but not in Group 2. Adhesive failure was mainly observed in Group 1, whereas dentin failure was the main failure pattern in Group 3.

Effect of professional dental prophylaxis on the surface gloss and roughness of CAD/CAM restorative materials

Background This study aimed to evaluate the effect of dental prophylaxis on the surface gloss and roughness of different indirect restorative materials for computer-aided design/computer-aided manufacturing (CAD/CAM): two types of CAD/CAM composite resin blocks (Shofu Block HC and Estelite Block) and two types of CAD/CAM ceramic blocks (IPS Empress CAD and Celtra DUO). Material and Methods After polishing the CAD/CAM blocks and applying prophylaxis pastes, professional dental prophylaxis was performed using four different experimental protocols (n = 5 each): mechanical cleaning with Merssage Regular for 10 s four times (Group 1); four cycles of mechanical cleaning with Merssage Regular for 10 s and Merssage Fine for 10 s (Group 2); four cycles of mechanical cleaning with Merssage Regular for 10 s and Merssage Fine for 30 s (Group 3); and mechanical cleaning with Merssage Fine for 10 s four times (Group 4). A glossmeter was used to measure surface gloss before and after mechanical cleaning, and a contact stylus profilometer was used to measure surface roughness (Ra). Results Polishing with prophylactic paste led to a significant reduction in surface gloss and increase in surface roughness among resin composite blocks, whereas the polishing-related change in surface gloss or roughness was smaller in Celtra DUO, a zirconia-reinforced lithium silicate block. Conclusions Changes in surface gloss and roughness due to polishing with a prophylactic paste containing large particles were not improved by subsequent polishing with a prophylactic paste containing fine particles. Key words:CAD/CAM, professional dental prophylaxis, prophylactic paste, surface gloss, surface roughness.

Influence of handpiece maintenance sprays on resin bonding to dentin

Objective To investigate the influence of maintenance spray on resin bonding to dentin. Materials and methods The crown of extracted, caries-free human molars was transversally sectioned with a model trimmer to prepare the dentin surfaces from mid-coronal sound dentin, and then uniformly abraded with #600 silicon carbide paper. The dentin surfaces were randomly divided into three groups: oil-free spray group where maintenance cleaner for air bearing handpieces was sprayed onto the dentin surface for 1 s and rinsed with water spray for 30 s; oil-containing spray group where maintenance cleaner for micro motor handpieces was sprayed onto the dentin surface for 1 s and rinsed with water spray for 30 s; and control group where the surface was rinsed with water spray for 30 s and then air-dried. These surfaces were then bonded with Clearfil SE Bond (Kuraray Medical), and resin composite (Clearfil AP-X, Kuraray Medical) build-up crowns were incrementally constructed on the bonded surfaces. After storage for 24 h in 37°C water, the bonded teeth were sectioned into hour-glass shaped slices (0.7-mm thick) perpendicular to the bonded surfaces. The specimens were then subjected to microtensile bond strength (μTBS) testing at a crosshead speed of 1.0 mm/min. Data were analyzed with one-way ANOVA and the Tukey-Kramer test. Results Maintenance spray-contaminated specimens (oil-free and oil-containing spray groups) showed significantly lower μTBS than control specimens (P < 0.05). However, there was no significant difference between the spray-contaminated groups (P > 0.05). Conclusion Maintenance spray significantly reduces the bond strength of Clearfil SE Bond to dentin.

Combined effects of electric toothbrushing and dentifrice on artificial stain removal: an in vitro study

Background This in vitro study aimed to clarify the combined effect of electric toothbrushing and dentifrice on the removal of artificial stain. Material and Methods Twenty-five bovine incisors were cut at the cervix and the crown was embedded in auto-cured acrylic resin. Specimens were abraded using #240 SiC paper to obtain a flat enamel surface, and 20 specimens were treated with 10% citric acid / 3% ferric chloride solution followed by 1% tannic acid solution to produce surface staining. They were divided into four groups: 1) brushing with an electric toothbrush and whitening dentifrice (group S+B); 2) brushing with an electric toothbrush and fluoride dentifrice (group S+C); 3) brushing with an electric toothbrush and no dentifrice (group S); and 4) no brushing (control group). The remaining five specimens were used as a baseline. Color values (L*, a*, and b* were measured before brushing (0 min), and at 1 min, 5 min, 10 min, and 20 min using a microscopic area spectrophotometer. The color change (ΔE) was calculated by subtracting the baseline values from the final color values obtained at each time point. The data were statistically analyzed using two-way repeated-measures analysis of variance and Tukey’s honest significant difference test as a post hoc test (p<0.05). Results The L* values of groups S+B and S+C increased over time (p<0.05), but no significant differences were observed in group S and the control group at any of the time points (p>0.05). Groups S+B and S+C demonstrated greater ΔE values than group S. Conclusions The combination of electric toothbrushing and dentifrice removed the artificial stain more effectively than brushing without dentifrice. However, the stain removal was limited. The two dentifrices evaluated in this study exhibited similar stain removal effects. Key words:Color change, stain removal, dentifrice, electric toothbrush, whitening effect.

Resin Bonding of Self-Etch Adhesives to Bovine Dentin Bleached from Pulp Chamber.

This study evaluated the microtensile bond strength (μTBS) of 1-step self-etch adhesives (1-SEAs) and 2-step self-etch adhesives (2-SEAs) to pulp chamber dentin immediately after bleaching with 2 types of common bleaching techniques. Pulp chamber dentin of bovine teeth was bleached using 30% hydrogen peroxide (H2O2) solution with quartz-tungsten-halogen light-curing unit (Group 1) and 3.5% H2O2-containing titanium dioxide (TiO2) (Pyrenees®) activated with 405-nm violet diode laser for 15 min (Group 2). Unbleached specimens were placed in distilled water for 15 min and used as controls. After treatment, dentin was bonded with resin composite using 1-SEA or 2-SEA and stored in water at 37°C for 24 h. Each specimen was sectioned and trimmed to an hourglass-shape and μTBS was measured. Fractured specimens were examined under a scanning electron microscope to determine fracture modes. All specimens in Group 1 failed before proper bonding tests. In Group 2, the μTBS of 2-SEA was significantly greater (with no failed specimens) than 1-SEA (where 21 out of 36 failed). These results indicate that 2-SEA is a better adhesive system than 1-SEA on bleached dentin. Our results also demonstrated that application of H2O2 significantly decreases bond strength of resin to dentin; however, in the case of nonvital tooth bleaching, Pyrenees® is a better alternative to the conventional 30% H2O2 bleaching.