Ales Mizera

Cross-linked low density polyethylene mechanical properties after temperature load at 110, 180 and 220 °C

Radiation processing of polymers is a well-established and economical commercial method of precisely modifying the properties of polymers, especially mechanical properties. The mechanical properties of modified low density polyethylene samples by beta rays were measured at the ambient temperature and after temperature load above the pure low density polyethylene melting temperature. The tested samples showed significant changes of mechanical behaviour before and after temperature load. From this point of view, new applications could also be seen in areas with service temperatures higher than their former melting point, especially for application with short time exposure of temperature load.

Hardness/microhardness properties of HDPE blends

This paper deals with utilization of recycled irradiated high-density polyethylene (rHDPEx) as a filler which was blended with non-modified high-density polyethylene (HDPE). Two blends were tested regarding the original state of the mixing components – HDPE granules/rHDPEx grit and HDPE granules/rHDPEx powder. Results show that the increasing amount of the rHDPEx, regardless its form, results in worsening both observed parameters – hardness and micro-indentation hardness.

Surface Layer Micro-Hardness of Modified LDPE by Radiation Cross-Linking after Temperature Load

The presented article deals with the research of surface layer ́s micro-mechanical properties of modified LDPE by radiation cross-linking after temperature load. These micro-mechanical properties were measured by the DSI (Depth Sensing Indentation) method on samples which were non-irradiated and irradiated by different doses of the β – radiation and then were temperature loaded. The purpose of the article is to consider to what extent the irradiation process influences the resulting micro-mechanical properties measured by the DSI method. The LDPE tested showed significant changes of indentation hardness and modulus after temperature load.

Effect of High Doses Beta Irradiation on the Micromechanical Properties of Surface Layer of Glass-Filled Polypropylene

The presented article deals with the research of micro-mechanical properties in the surface layer of modified Polypropylene filled by 25% of glass fibers. These micro-mechanical properties were measured by the Depth Sensing Indentation - DSI method on samples which were non-irradiated and irradiated by different doses of the β - radiation. Radiation doses used were 0, 66 and 99 kGy for filled Polypropylene with the 6% cross-linking agent (triallyl isocyanurate). The change of micromechanical properties is greatly manifested mainly in the surface layer of the modified polypropylene where a significant growth of microhardness values can be observed.

Mechanical Properties Changes of Irradiated Thermoplastic Elastomer

Some polymers need a cross-linking agent for the controlled cross-linking process of polymers with a tendency to degradation during the radiation cross-linking process. While, on the other hand, other polymers do not need a cross-linking agent—predominantly there are cross-linking polymers. The Thermo-Plastic Elastomer (TPE) that was used belongs to this group of predominantly cross-linking polymers; however, this agent is added because of faster reaction times and smaller irradiation doses. Microindentation–tensile and tensile impact tests were carried out on a thermoplastic sample—with, and without, a cross-linking agent. Small changes were measured between these materials at low radiation doses, (up to 66 kGy); nevertheless, at higher doses, the influence of the cross-linking agent on the mechanical properties is significant.

Mechanical properties of irradiated polyamide under thermal stress

It was found in this study, that radiation crosslinking has a positive effect on the mechanical properties of selected type polyamide. In recent years, there have been increasing requirements for quality and cost effectiveness of manufactured products in all areas of industrial production. These requirements are best met with the polymeric materials, which have many advantages in comparison to traditional materials. The main advantages of polymer materials are especially in their ease of processability, availability, and price of the raw materials. Radiation crosslinking is one of the ways to give the conventional plastics mechanical, thermal, and chemical properties of expensive and highly resistant construction polymers. The main purpose of this paper has been to determine the effect of radiation crosslinking on the tensile strength and elongation of PA 66 (filled with 30 % glass fibers). These properties were examined in dependence on the dosage of the ionizing electron beam radiation (non-irradiated samples and those irradiated by dosage 66 and 132 kGy were compared) and on the test temperature (23, 50, 80, and 110 oC). Radiation cross-linking of PA 66 results in increased mechanical strength, and decreased of elongation. As an addition, the increased surface microhardness of polyamide was found.

The Effect of Irradiation on Mechanical and Thermal Properties of Selected Types of Polymers

This article deals with the influence of electron-beam radiation on the micro-mechanical, thermo-mechanical, and structural properties of selected polymers. In the search for the desired improvement of polymers, it is possible to use, inter alia, one particular possible modification—Namely, crosslinking—Which is a process during which macromolecular chains start to connect to each other and, thus, create the spatial network in the structure. In the course of the treatment of the ionizing radiation, two actions can occur: crosslinking and scission of macromolecules, or degradation. Both these processes run in parallel. Using the crosslinking technology, standard and technical polymers can acquire the more “expensive” high-tech polymeric material properties and, thus, replace these materials in many applications. The polymers that were tested were selected from across the whole spectra of thermoplastics, ranging from commodity polymers, technical polymers, as well as high-performance polymers. These polymers were irradiated by different doses of beta radiation (33, 66, 99, 132, 165, and 198 kGy). The micro-mechanical and thermo-mechanical properties of these polymers were measured. When considering the results, it is obvious that irradiation acts on each polymer differently but, always when the optimal dose was found, the mechanical properties increased by up to 36%. The changes of micro-mechanical and thermo-mechanical properties were confirmed by structural measurement when the change of the micro-hardness and modulus corresponded to the crystalline phase change as determined by X-ray and gel content.

Surface and Adhesive Properties of Low-Density Polyethylene after Radiation Cross-Linking

Radiation cross-linking gives inexpensive commodity plastics and technical plastics the mechanical, thermal, and chemical properties of high-performance plastic. This upgrading of the plastics enables them to be used in conditions which they would not be able to with stand otherwise. The irradiation cross-linking of thermoplastic materials via electron beam or cobalt 60 (gammy rays) is performed separately, after processing. Generally, ionizing radiation includes accelerated electrons, gamma rays and X-rays. Radiation processing with an electron beam offers several distinct advantages when compared with other radiation sources, particularly γ-rays and x-rays. The process is very fast, clean and can be controlled with much precision. There is no permanent radioactivity since the machine can be switched off. In contrast to γ-rays and x-rays, the electron beam can steered relatively easily, thus allowing irradiation of a variety of physical shapes. The energy-rich beta rays trigger chemical reactions in the plastics which results in networking of molecules (comparable to the vulcanization of rubbers which has been in industrial use for so long). The energy from the rays is absorbed by the material and cleavage of chemical bonds takes place. This releases free radicals which in next phase from desired molecular bonds. This article describes the effect of radiation cross-linking on the surface and adhesive properties of low-density polyethylene.

Use of Irradiated Polymers after Their Lifetime Period

This article deals with the study of the utilisation of irradiated HDPE products after their end-of-life cycle. Today, polymer waste processing is a matter of evermore intensive discussion. Common thermoplastic waste recycling—especially in the case of wastes with a defined composition—is generally well-known—and frequently used. On the contrary, processing cross-linked plastics is impossible to do in the same way as with virgin thermoplastics—mainly due to the impossibility of remelting them. The possibility of using waste in the form of grit or a powder, made from cross-linked High Density PolyEthylene (rHDPEx) products, after their end-of-life cycle, as a filler for virgin Low Density PolyEthylene (LDPE) was tested in a matrix. It was found that both the mechanical behaviour and processability of new composites with an LDPE matrix, with rHDPEx as a filler, depend—to a high degree—on the amount of the filler. The composite can be processed up to 60% of the filler content. The Polymer Mixture Fluidity dropped significantly, in line with the amount of filler, while the mechanical properties, on the other hand, predominantly grew with the increasing amount of rHDPEx.

The Electrical, Mechanical and Surface Properties of Thermoplastic Polyester Elastomer Modified by Electron Beta Radiation

The main advantages of Thermoplastic Polyester Elastomers (TPE-E) are their elastomer properties as well as their ability to be processed in the same way as thermoplastic polymers (e.g., injection moulding, compression moulding and extrusion). However, TPE-Es’ properties, mainly their mechanical properties and thermal characteristics, are not as good as those of elastomers. Because of this TPE-Es are often modified with the aim of improving their properties and extending their range of application. Radiation cross-linking using accelerated electron beams is one of the most effective ways to change virgin polymers’ properties significantly. Their electrical (that is to say permittivity and resistivity measurements), mechanical (that is, tensile and impact tensile tests), as well as surface (that is, nano-indentation) properties were measured on modified/cross-linked TPE-E specimens with and/or without a cross-linking agent at irradiation doses of 0, 33, 66, 99, 132, 165 and 198 kGy. The data acquired from these procedures show significant changes in the measured properties. The results of this study allow the possibility of determining the proper processing parameters and irradiation doses for the production of TPE-E products which leads to the enlargement of their application in practice.