Alihan Kaya

Low mass quality flow boiling in microtubes at high mass fluxes

In this article, an experimental study on boiling heat transfer and fluid flow in microtubes at high mass fluxes is presented. De-ionized water flow was investigated over a broad range of mass flux (1000 kg/m2s-7500 kg/m2s) in microtubes with inner diameters of ~ 250 micrometers and ~ 685 micrometers. The reason for using two different capillary diameters was to investigate the size effect on flow boiling. De-ionized water was used as working fluid, and the test section was heated by Joule heating. Heat transfer coefficients and qualities were deduced from local temperature measurements. It was found that high heat removal rates could be achieved at high flow rates under subcooled boiling conditions. It was also observed that heat transfer coefficients increased with mass flux, whereas they decreased with local quality and heat flux. Moreover, experimental heat flux data were compared with partial boiling correlations and fully developed correlations. It was observed that at low wall superheat values there was only a small inconsistency between the experimental data and the conventional partial boiling prediction method of Bergles, while the subcooled and low quality fully developed boiling heat transfer correlation of Kandlikar could fairly predict experimental results at high wall superheat values.

Experimental Study on Convective Heat Transfer Performance of Iron Oxide Based Ferrofluids in Microtubes

Ferrofluids are colloidal suspensions, in which the solid phase material is composed of magnetic nanoparticles, while the base fluid can potentially be any fluid. The solid particles are held in suspension by weak intermolecular forces and may be made of materials with different magnetic properties. Magnetite is one of the materials used for its natural ferromagnetic properties. Heat transfer performance of ferrofluids should be carefully analyzed and considered for their potential of their use in wide range of applications. In this study, convective heat transfer experiments were conducted in order to characterize convective heat transfer enhancements with Lauric acid coated ironoxide (Fe3O4) nanoparticle based ferrofluids, which have volumetric fractions varying from 0% to ~5% and average particle diameter of 25 nm, in a hypodermic stainless steel microtube with an inner diameter of 514 Hm, an outer diameter of 819 Hm, and a heated length of 2.5 cm. Heat fluxes up to 184 W/cm2 were applied to the system at three different flow rates (1ml/s, 0.62ml/s and 0.36 ml/s). A decrease of around 100% in the maximum surface temperature (measured at the exit of the microtube) with the ferrofluid compared to the pure base fluid at significant heat fluxes (>100 W/cm2) was observed. Moreover, the enhancement in heat transfer increased with nanoparticle concentration, and there was no clue for saturation in heat transfer coefficient profiles with increasing volume fraction over the volume fraction range in this study (0%-5%). The promising results obtained from the experiments suggest that the use of ferrofluids for heat transfer, drug delivery, and biological applications can be advantageous and a viable alternative as new generation coolants and futuristic drug carriers.

Heat Transfer Enhancement With Iron Oxide Nanoparticle Based Ferrofluids

Nanofluids are colloidal compounds, where the solid phase material is composed of nano sized particles, and the liquid phase can potentially be any fluid but aqueous media are common. As a common nanofluid type, ferrofluids are formed by holding solid nanoparticles in suspension by weak intermolecular forces and may be produced from materials with different magnetic properties. Heat transfer performance of ferrofluids is one of the crucial properties among many others that should be analyzed and considered for their wide range of applications. For this purpose, experiments were conducted in order to characterize heat transfer properties of ironoxide based ferrofluids flowing through a microchannel. In this study, convective heat transfer experiments were conducted in order to characterize convective heat transfer enhancements with Lauric acid coated ironoxide (Fe3O4) nanoparticle based ferrofluids, which have volumetric fractions between 0%–∼5% and average particle diameter of 25 nm, in a 2.5 cm long hypodermic stainless steel microtube with an inner diameter of 514 μm and an outer diameter of 819 μm. Heat fluxes up to 184 W/cm2 were applied to the system at three different flow rates (1ml/s, 0.62ml/s and 0.36 ml/s). Promising results were obtained from this study, which are suggesting the use of ferrofluids for heat transfer applications can be advantageous.Copyright

An experimental study on heat transfer performance of iron oxide based ferrofluids

Nanofluids are colloidal compounds, where the solid phase material is composed of nano sized particles, and the liquid phase can potentially be any fluid but aqueous media are common. As a common nanofluid type, ferrofluids are formed by holding solid nanoparticles in suspension by weak intermolecular forces and may be produced from materials with different magnetic properties. Magnetite is one of the materials used for its natural ferromagnetic properties. Heat transfer performance of ferrofluids is one of the crucial properties among many others that should be analyzed and considered for their wide range of applications. For this purpose, experiments were conducted in order to characterize heat transfer properties of ironoxide based ferrofluids flowing through a microchannel. Promising results were obtained from this study, which are suggesting the use of ferrofluids for heat transfer applications can be advantageous.Copyright