Anastasia V. Riazanova

Synthesis of fe-doped zno nanorods by rapid mixing hydrothermal method and its application for high performance UV photodetector

We have successfully synthesized Fe-doped ZnO nanorods by a new and simple method in which the adopted approach is by using ammonia as a continuous source of OH- for hydrolysis instead of hexamethylenetetramine (HMT). The energy dispersive X-ray (EDX) spectra revealed that the Fe peaks were presented in the grown Fe-doped ZnO nanorods samples and the X-ray photoelectron spectroscopy (XPS) results suggested that Fe3+ is incorporated into the ZnO lattice. Structural characterization indicated that the Fe-doped ZnO nanorods grow along the c-axis with a hexagonal wurtzite structure and have single crystalline nature without any secondary phases or clusters of FeO or Fe3O4 observed in the samples. The Fe-doped ZnO nanorods showed room temperature (300 K) ferromagnetic magnetization versus field (M-H) hysteresis and the magnetization increases from 2.5 µemu to 9.1 µemu for Zn0.99Fe0.01O and Zn0.95Fe0.05O, respectively. Moreover, the fabricated Au/Fe-doped ZnO Schottky diode based UV photodetector achieved 2.33 A/W of responsivity and 5 s of time response. Compared to other Au/ZnO nanorods Schottky devices, the presented responsivity is an improvement by a factor of 3.9.

Pattern shape control for heat treatment purification of electron-beam-induced deposition of gold from the Me2Au(acac) precursor.

Gold structures can be created in a scanning electron microscope (SEM) from the Me(2)Au(acac) precursor by direct writing with the electron beam. The as-deposited purity is usually poor, and a common purification approach is a post-annealing step that indeed is effective but also induces a volume reduction because of carbon loss and an undesirable reconfiguration of the gold structure, resulting in the loss of the original shape. We studied the shape change as a result of such purification, and to minimize this effect, the application of a tantalum and chromium buffer layer was investigated. These buffer materials are well-known for their good adhesion properties. We confirm by dedicated SEM, atomic force microscopy (AFM), and transmission electron microscopy (TEM) analysis that, for the creation of a uniform Au structure, tantalum is a better buffer layer material than chromium. Post-annealing of the Au electron-beam-induced deposition (EBID) patterns for 1 h at 600 °C in air resulted in a dramatic purity increase (from 8-12 atomic % Au to above 92 atomic % Au). The uncovered part of the tantalum layer can be easily etched away, resulting in a well-defined, high-purity, gold structure.

Bioinspired Layer-by-Layer Microcapsules Based on Cellulose Nanofibers with Switchable Permeability

Green, all-polysaccharide based microcapsules with mechanically robust capsule walls and fast, stimuli-triggered, and switchable permeability behavior show great promise in applications based on selective and timed permeability. Taking a cue from nature, the build-up and composition of plant primary cell walls inspired the capsule wall assembly, because the primary cell walls in plants exhibit high mechanical properties despite being in a highly hydrated state, primarily owing to cellulose microfibrils. The microcapsules (16 ± 4 μm in diameter) were fabricated using the layer-by-layer technique on sacrificial CaCO3 templates, using plant polysaccharides (pectin, cellulose nanofibers, and xyloglucan) only. In water, the capsule wall was permeable to labeled dextrans with a hydrodynamic diameter of ∼6.6 nm. Upon exposure to NaCl, the porosity of the capsule wall quickly changed allowing larger molecules (∼12 nm) to permeate. However, the porosity could be restored to its original state by removal of NaCl, by which permeants became trapped inside the capsules core. The high integrity of cell wall was due to the CNF and the ON/OFF alteration of the permeability properties, and subsequent loading/unloading of molecules, could be repeated several times with the same capsule demonstrating a robust microcontainer with controllable permeability properties.

In situ manufacture of magnetic tunnel junctions by a direct-write process

In situ construction of Co/SiO2/Co magnetic tunnel junctions using direct-write electron-beam-induced deposition is described. Proof-of-concept devices were built layer by layer depositing the specific components one at a time, allowing device manufacture using a strictly additive process. The devices exhibit a magnetic tunneling signature which agrees qualitatively with the Slonczewski model of magnetic tunneling.

Superamphiphobic coatings based on liquid-core microcapsules with engineered capsule walls and functionality

Microcapsules with specific functional properties, related to the capsule wall and core, are highly desired in a number of applications. In this study, hybrid cellulose microcapsules (1.2 ± 0.4 µm in diameter) were prepared by nanoengineering the outer walls of precursor capsules. Depending on the preparation route, capsules with different surface roughness (raspberry or broccoli-like), and thereby different wetting properties, could be obtained. The tunable surface roughness was achieved as a result of the chemical and structural properties of the outer wall of a precursor capsule, which combined with a new processing route allowed in-situ formation of silica nanoparticles (30–40 nm or 70 nm in diameter). By coating glass slides with “broccoli-like” microcapsules (30–40 nm silica nanoparticles), static contact angles above 150° and roll-off angles below 6° were obtained for both water and low surface-tension oil (hexadecane), rendering the substrate superamphiphobic. As a comparison, coatings from raspberry-like capsules were only strongly oleophobic and hydrophobic. The liquid-core of the capsules opens great opportunities to incorporate different functionalities and here hydrophobic superparamagnetic nanoparticles (SPIONs) were encapsulated. As a result, magnetic broccoli-like microcapsules formed an excellent superamphiphobic coating-layer on a curved geometry by simply applying an external magnetic field.

Enhanced photoresponse of inkjet printed ZnO thin films induced by chemically capped CdS nanoparticles by dip coating

Monodispersed CdS nanoparticles (NP) are dip coated on porous ZnO thin film deposited by inkjet printing. Optical absorption characteristics of the composite films show that the composite exhibits two main peaks centered at 355 nm due to the absorption at UV region from ZnO, and 433 nm arising from CdS NP. On UV radiations the electrical conductivity of CdS/ZnO composite thin film with 5 dip cycles is found to be enhanced more than three orders magnitude compared with that of the ZnO which we attribute to be the effect of interfacial charge transfer. Also, the UV photoresponse of ZnO shows pronounced enhancement after CdS capping.