Andrew E. Dadson

Core-shell diamond as a support for solid-phase extraction and high-performance liquid chromatography.

We report the formation of core-shell diamond particles for solid-phase extraction (SPE) and high-performance liquid chromatography (HPLC) made by layer-by-layer (LbL) deposition. Their synthesis begins with the amine functionalization of microdiamond by its immersion in an aqueous solution of a primary amine-containing polymer (polyallylamine (PAAm)). The amine-terminated microdiamond is then immersed in an aqueous suspension of nanodiamond, which leads to adsorption of the nanodiamond. Alternating (self-limiting) immersions in the solutions of the amine-containing polymer and the suspension of nanodiamond are continued until the desired number of nanodiamond layers is formed around the microdiamond. Finally, the core-shell particles are cross-linked with 1,2,5,6-diepoxycyclooctane or reacted with 1,2-epoxyoctadecane. Layer-by-layer deposition of PAAm and nanodiamond is also studied on planar Si/SiO(2) surfaces, which were characterized by scanning electron microscopy (SEM), Rutherford backscattering spectrometry (RBS), and nuclear reaction analysis (NRA). Core-shell particles are characterized by diffuse reflectance infrared Fourier transform spectroscopy (DRIFT), environmental scanning electron microscopy (ESEM), and Brunauer-Emmett-Teller (BET) surface area and pore size measurements. Larger (ca. 50 microm) core-shell diamond particles have much higher surface areas and analyte loading capacities in SPE than nonporous solid diamond particles. Smaller (ca. 3 microm), normal and reversed-phase, core-shell diamond particles have been used for HPLC, with 36,300 plates/m for mesitylene in a separation of benzene and alkyl benzenes and 54,800 plates/m for diazinon in a similar separation of two pesticides on a C(18) adsorbent.

Stable, Microfabricated Thin Layer Chromatography Plates without Volume Distortion on Patterned, Carbon and Al2O3-Primed Carbon Nanotube Forests

Some of us recently described the fabrication of thin layer chromatography (TLC) plates from patterned carbon nanotube (CNT) forests via direct infiltration/coating of the CNTs by low pressure chemical vapor deposition (LPCVD) of silicon from SiH₄, followed by high temperature oxidation of the CNTs and Si. Herein we present an improved microfabrication process for the preparation of these TLC plates. First, a few nanometers of carbon and/or a thin film of Al₂O₃ is deposited on the CNTs. This method of priming the CNTs for subsequent depositions appears to be new. X-ray photoelectron spectroscopy confirms the presence of additional oxygen after carbon deposition. After priming, the plates are coated by rapid, conformal deposition of an inorganic material that does not require subsequent oxidation, i.e., by a fast pseudo atomic layer deposition (ψ-ALD) of SiO₂ from trimethylaluminum and tris(tert-butoxy)silanol. Unlike devices described previously, faithful reproduction of the features in the masks is still observed after oxidation. A bonded, amino phase on the resulting plates shows fast, highly efficient separations of fluorescent dyes (plate heights in the range of 1.6-7.7 μm). Extensive characterization of the new materials by TEM, SEM, EDAX, DRIFT, and XPS is reported. A substantially lower process temperature for the removal of the CNT scaffold is possible as a result of the already oxidized materials used.

Amino-Modified Diamond as a Durable Stationary Phase for Solid-Phase Extraction

We report the formation of a highly stable amino stationary phase on diamond and demonstrate its use in solid-phase extraction (SPE). This process consists of spontaneous and self-limiting adsorption of polyallylamine (PAAm) from aqueous solution onto oxidized diamond. Thermal curing under reduced pressure or chemical cross-linking with a diepoxide was shown to fix the polymer to the particles. The resulting adsorbents are stable under even extreme pH conditions (from at least pH 0-14) and significantly more stable than a commercially available amino SPE adsorbent. Coated diamond particles were characterized by X-ray photoelectron spectroscopy (XPS) and diffuse reflectance Fourier transform-infrared spectroscopy (DRIFT). Model silicon surfaces were characterized by spectroscopic ellipsometry and wetting. Solid-phase extraction was demonstrated using cholesterol, hexadecanedioic acid, and palmitoyloleoylphosphatidylcholine as analytes, and these results were compared to those obtained with commercially available materials. Breakthrough curves indicate that, as expected, porous diamond particles have higher analyte capacity than nonporous solid particles.

Silicon (100)/SiO2 by XPS

Silicon (100) substrates are ubiquitous in microfabrication and, accordingly, their surface characteristics are important. Herein, we report the analysis of Si (100) via X-ray photoelectron spectroscopy (XPS) using monochromatic Al Kα radiation. Survey scans show that the material is primarily silicon and oxygen with small amounts of carbon, nitrogen, and fluorine contamination. The Si 2p region shows two peaks that correspond to elemental silicon and silicon dioxide. Using these peaks the thickness of the native oxide (SiO2) is estimated using the equation of Strohmeier. The oxygen peak is symmetric. These silicon wafers are used as the substrate for subsequent growth of templated carbon nanotubes in the preparation of microfabricated thin layer chromatography plates.

C18, C8, and perfluoro reversed phases on diamond for solid-phase extraction

In spite of advances in solid-phase extraction (SPE) technology there are certain disadvantages to current SPE silica-based, column packings. The pH range over which extraction can occur is limited and each column is generally only used once. New diamond-based reversed SPE phases (C(18), C(8), and perfluorinated) were developed in our laboratories. Studies were done which show that these phases do not have the same limitations as traditional silica-based stationary phases. The synthesis and properties of these diamond-based phases are presented, and the stability, percent recovery, and column capacity are given for the C(18) phase.

Ozone priming of patterned carbon nanotube forests for subsequent atomic layer deposition-like deposition of SiO2 for the preparation of microfabricated thin layer chromatography plates

The authors report the ozonation of patterned, vertically aligned carbon nanotube (CNT) forests as a method of priming them for subsequent pseudo atomic layer deposition (ψ-ALD) (alternating layer deposition) of silica to produce microfabricated, CNT-templated thin layer chromatography (TLC) plates. Gas phase ozonation simplifies our deposition scheme by replacing two steps in our previous fabrication process: chemical vapor deposition of carbon and ALD of Al2O3, with this much more straightforward priming step. As shown by x-ray photoelectron spectroscopy (XPS), ozonation appears to prime/increase the number of nucleation sites on the CNTs by oxidizing them, thereby facilitating conformal growth of silica by ψ-ALD, where some form of priming appears to be necessary for this growth. (As shown previously, ψ-ALD of SiO2 onto unprimed CNTs is ineffective and leads to poor quality depositions.) In conjunction with a discussion of the challenges of good peak fitting of complex C 1s XPS narrow scans, the author...

Effects of catalyst thickness on the fabrication and performance of carbon nanotube-templated thin layer chromatography plates

The effects of iron catalyst thickness on the fabrication and performance of microfabricated, binder-free, carbon nanotube (CNT)-templated, thin layer chromatography (TLC) plates are demonstrated. The iron catalyst was deposited at thicknesses ranging from 4 to 18 nm in increments of 2 nm. Its thickness plays a key role in governing the integrity and separation capabilities of microfabricated TLC plates, as determined using a test dye mixture. Atomic force microscopy and scanning electron microscopy show that smaller and more numerous catalyst nanoparticles are formed from thinner Fe layers, which in turn govern the diameters and densities of the CNTs. The average diameter of the Fe nanoparticles, Dp, is approximately six times the initial Fe film thickness, tFe: Dp ≈ 6tFe. After deposition of relatively thick silicon layers on CNTs made with different Fe thicknesses, followed by oxidation, all of the resulting CNT-templated SiO2 wires had nearly the same diameter. Consequently, their surface areas were v...

Improved efficiency of reversed-phase carbon/nanodiamond/polymer core-shell particles for HPLC using carbonized poly(divinylbenzene) microspheres as the core materials.

Here, we report efficiencies up to 112,000 plates per meter (a reduced plate height, h, of 2.22) for RP, carbon/nanodiamond/aminopolymer particles using conventional injection conditions in HPLC. This efficiency greatly exceeds our best previously reported value of 71,000 N/m (h = 3.52). The carbon cores used in this study were derived from carbonized poly(divinylbenzene) spheres that were either made in-house by a two-step polymerization procedure or obtained commercially. The resulting particles showed good uniformity and were oxidized in nitric acid to increase their dispersability. X-ray photoelectron spectroscopy confirms particle oxidation and subsequent aminopolymer deposition. Layer-by-layer (LbL) growth of poly(allyamine) and nanodiamond was demonstrated to produce core-shell particles. After LbL growth, the particles were functionalized, sieved, and packed into columns. The column functionalization and packing were reproducible. Van Deemter curves indicated that the commercially obtained poly(divinylbenzene) spheres outperformed those synthesized in our laboratory. The columns appear to be stable at 120°C in a pH 11.3 mobile phase. Longer columns (2.1 × 50 mm) than previously reported were packed. Four essential oils were separated by gradient elution.

Al2O3 e-Beam Evaporated onto Silicon (100)/SiO2, by XPS

We report the XPS characterization of a thin film of Al2O3 (35 nm) deposited via e-beam evaporation onto silicon (100). The film was characterized with monochromatic Al Kα radiation. An XPS survey scan, an Al 2p narrow scan, an O 1s narrow scan, and the valence band spectrum were collected. The Al2O3 thin film is used as a diffusion barrier layer for templated carbon nanotube (CNT) growth in the preparation of microfabricated thin layer chromatography plates.

Thermally Evaporated Iron (Oxide) on an Alumina Barrier Layer, by XPS

We report the XPS characterization of a thermally evaporated iron thin film (6 nm) deposited on an Si/SiO2/Al2O3 substrate using Al Kα x-rays. An XPS survey spectrum, Fe 2p and O 1s narrow scans, and a valence band scan are shown.