Antonio Uris

Extraordinary Sound Screening in Perforated Plates

We report extraordinary effects in the transmission of sound through periodically perforated plates, supported by both measurements and theory. In agreement with recent observations in slit arrays, M. H. Lu et al. [Phys. Rev. Lett. 99, 174301 (2007)10.1103/PhysRevLett.99.174301], nearly full transmission is observed at certain resonant frequencies, pointing out similarities of the acoustic phenomena and their optical counterpart. However, acoustic screening well beyond that predicted by the mass law is achieved over a wide range of wavelengths in the vicinity of the period of the array, resulting in fundamentally unique behavior of the sound as compared to light.

Effect of the rockwool bulk density on the airborne sound insulation of lightweight double walls

Abstract In this paper, results from measurements of the sound reduction index of some double walls are presented. The walls are made from gypsum boards and filled with sound-absorbing material (rockwool) in the gap. The results from the measurements show the influence of rockwool bulk density on the sound reduction index.

Design of lightweight multilayer partitions based on sonic crystals

The sound transmission coefficient of different multilayer partitions commonly encountered in buildings has been measured as a function of frequency. Most of the samples studied showed an increase in the sound transmission coefficient over a specific frequency, called the critical frequency, depending on the layer material. However, for partitions built with the same materials, but built with a periodic arrangement of layers, this behavior has not been observed. This kind of periodic multilayer partition can be considered as a sonic crystal, because the stopband corresponding to a one-dimensional sonic crystal with a constant lattice equal to the modulation of the partition is in the same range as the critical frequency of the panel.

Influence of screw spacings on sound reduction index in lightweight partitions

Abstract In this paper measured sound reduction index data for lightweight partitions with gypsum board layers attached to the frame with two different screw spacings are presented. Data are used to show the effect of screw spacings and to quantify the effect on sound reduction index. The results show that screw spacing had a great effect in double walls where each gypsum board layer was attached to each side of a timber frame.

Acoustic radiation efficiency of a periodically corrugated rigid piston

The radiation of sound by a periodically corrugated rigid piston is explored using theoretical and numerical approaches and compared with the radiation of flat rigid piston. The depth and the period of the corrugation are considered to be comparable with the wavelength in the surrounding fluid. Radiation enhancement is predicted due to cavity resonances and coherent diffraction. In addition, broad regions of low radiation efficiency are observed. Both effects could have an impact in acoustic transducers technology, either to increase the piston radiated power or to create a source of evanescent acoustic waves. The possibilities offered by this strategy in the nonlinear acoustic regime are also briefly discussed.

Sound transmission through plates perforated with two periodic subwavelength hole arrays

Theoretical results on sound transmission through plates perforated with compound periodic hole arrays are presented. Calculations are obtained by means of a model under the rigid-solid assumption, which is thoroughly derived. A complex interplay between resonant transmission peaks, resonance interference, and Wood anomaly minima is observed. At high frequencies the resonant peaks overcome the Wood anomaly dips, leading to a different behaviour when compared with simple hole arrays.

Influence of air layers and damping layers between gypsum boards on sound transmission

Abstract In this paper the influence on sound reduction index of a thin air layer between gypsum board layers of lightweight partitions has been examined. It has been shown that the air layer between gypsum boards causes a decrease in sound reduction index due to mass-air-mass resonance. When the thin air layer is filled with a damping layer, the sound reduction index is increased for frequencies around the critical frequencies. Predictions show similar effects to those measured.

Community response to road traffic noise in the littoral region near Valencia (Spain)

The road traffic noise in three different cities and community response is presented in this paper. Road traffic noise is obtained by the equivalent continuous sound pressure level. To obtain the community response a questionnaire has been designed. Results from measurements and questionnaire have been compared and it has been found out that heavy goods traffic noise is the origin of disturbance and indisposition.

Subwavelength slit acoustic metamaterial barrier

Reduction of noise in the transmission path is a very important environmental problem. The standard method to reduce this noise level is the use of acoustic barriers. In this paper, an acoustic metamaterial based on sound transmission through subwavelength slits, is tailored to be used as an acoustic barrier. This system consists of two rows of periodic repetition of vertical rigid pickets separated by a slit of subwavelength width, embedded in air. Here, both the experimental and the numerical analyses are presented. These analyses have facilitated the identification of the parameters that affect the insertion loss performance. The results demonstrated that the proposed barrier can be tuned to mitigate a band noise in a mechanical plant for buildings where openings for air flow are required as well as industrial noise, without excessive barrier thickness.

Ultrasonic lens based on a subwavelength slit surrounded by grooves.

The lensing capabilities of a single subwavelength slit surrounded by a finite array of grooves milled into a brass plate is presented. The modulation of the beam intensity of this ultrasonic lens can be adjusted by varying the groove depth. Numerical simulations as well as experimental validations at 290 kHz are shown. The experimental results are in good agreement with the numerical simulations. This system is believed to have potential applications for medical ultrasound fields such as tomography and therapy.