Arman Butt

Fabrication of Anti-Aging TiO2 Nanotubes on Biomedical Ti Alloys

The primary objective of this study was to fabricate a TiO2 nanotubular surface, which could maintain hydrophilicity over time (resist aging). In order to achieve non-aging hydrophilic surfaces, anodization and annealing conditions were optimized. This is the first study to show that anodization and annealing condition affect the stability of surface hydrophilicity. Our results indicate that maintenance of hydrophilicity of the obtained TiO2 nanotubes was affected by anodization voltage and annealing temperature. Annealing sharply decreased the water contact angle (WCA) of the as-synthesized TiO2 nanotubular surface, which was correlated to improved hydrophilicity. TiO2 nanotubular surfaces are transformed to hydrophilic surfaces after annealing, regardless of annealing and anodization conditions; however, WCA measurements during aging demonstrate that surface hydrophilicity of non-anodized and 20 V anodized samples decreased after only 11 days of aging, while the 60 V anodized samples maintained their hydrophilicity over the same time period. The nanotubes obtained by 60 V anodization followed by 600 °C annealing maintained their hydrophilicity significantly longer than nanotubes which were obtained by 60 V anodization followed by 300 °C annealing.

Thermally oxidized titania nanotubes enhance the corrosion resistance of Ti6Al4V

The negative impact of in vivo corrosion of metallic biomedical implants remains a complex problem in the medical field. We aimed to determine the effects of electrochemical anodization (60V, 2h) and thermal oxidation (600°C) on the corrosive behavior of Ti-6Al-4V, with serum proteins, at physiological temperature. Anodization produced a mixture of anatase and amorphous TiO2 nanopores and nanotubes, while the annealing process yielded an anatase/rutile mixture of TiO2 nanopores and nanotubes. The surface area was analyzed by the Brunauer-Emmett-Teller method and was estimated to be 3 orders of magnitude higher than that of polished control samples. Corrosion resistance was evaluated on the parameters of open circuit potential, corrosion potential, corrosion current density, passivation current density, polarization resistance and equivalent circuit modeling. Samples both anodized and thermally oxidized exhibited shifts of open circuit potential and corrosion potential in the noble direction, indicating a more stable nanoporous/nanotube layer, as well as lower corrosion current densities and passivation current densities than the smooth control. They also showed increased polarization resistance and diffusion limited charge transfer within the bulk oxide layer. The treatment groups studied can be ordered from greatest corrosion resistance to least as Anodized+Thermally Oxidized > Anodized > Smooth > Thermally Oxidized for the conditions investigated. This study concludes that anodized surface has a potential to prevent long term implant failure due to corrosion in a complex in-vivo environment.

A Novel Investigation of the Formation of TiO₂ Nanotubes on Thermally Formed Oxide of Ti-6Al-4V

Traditionally, titanium oxide (TiO2) nanotubes (TNTs) are anodized on Ti-6Al-4V alloy (Ti-V) surfaces with native TiO2 (amorphous TiO2); subsequent heat treatment of anodized surfaces has been observed to enhance cellular response. As-is bulk Ti-V, however, is often subjected to heat treatment, such as thermal oxidation (TO), to improve its mechanical properties. Thermal oxidation treatment of Ti-V at temperatures greater than 200°C and 400°C initiates the formation of anatase and rutile TiO2, respectively, which can affect TNT formation. This study aims at understanding the TNT formation mechanism on Ti-V surfaces with TO-formed TiO2 compared with that on as-is Ti-V surfaces with native oxide. Thermal oxidation-formed TiO2 can affect TNT formation and surface wettability because TO-formed TiO2 is expected to be part of the TNT structure. Surface characterization was carried out with field emission scanning electron microscopy, energy dispersive x-ray spectroscopy, water contact angle measurements, and white light interferometry. The TNTs were formed on control and 300°C and 600°C TO-treated Ti-V samples, and significant differences in TNT lengths and surface morphology were observed. No difference in elemental composition was found. Thermal oxidation and TO/anodization treatments produced hydrophilic surfaces, while hydrophobic behavior was observed over time (aging) for all samples. Reduced hydrophobic behavior was observed for TO/anodized samples when compared with control, control/anodized, and TO-treated samples. A method for improved surface wettability and TNT morphology is therefore discussed for possible applications in effective osseointegration of dental and orthopedic implants.

Novel functionalization of Ti-V alloy and Ti-II using atomic layer deposition for improved surface wettability

Surface wettability characteristics of commercially pure titanium (CP-Ti/Ti-II) and titanium Grade 5 alloy (Ti-6Al-4V/Ti-V) with 10nm-thick atomic layer deposited (ALD) TiO2 from Tetrakis DiEthyl Amino Titanium and water vapor were studied in conjunction with cleaning steps before and after the ALD treatment. The wettability characteristics of rough Ti-II and Ti-V samples were investigated after each step, that is, as received, after de-ionized (DI) water rinse followed by N2 drying, sonication in methanol, ALD treatment, and post-ALD DI water rinse. Samples without ALD or cleaning treatments were hydrophobic to variable extents, depending on exposure to different environments, surface impurities, roughness, and aging. Surface treatments reported in the literature resulted in hydrophilic/hydrophobic surfaces likely due to organic and/or inorganic impurities. In this study, (i) it is established that it is critically important to probe surface wettability after each substrate treatment; (ii) both Ti-II and Ti-V surfaces are found to become more hydrophilic after each one of the sequential treatments used; and (iii) independently of the initial wettability characteristics of Ti-II and Ti-V surfaces, the aforementioned treatments result in a water contact angle well below 10°, which is an important factor in cellular response. X-ray photoelectron spectroscopy of ALD titania films indicated trace impurities in them. Grazing incidence X-ray diffraction suggested amorphous ALD TiO2 at 200 °C; anatase TiO2 was obtained with as little as 5 min annealing at 600 °C in nitrogen.

Optimization of Anodization and Annealing Condition Enhances TiO 2 Nanotubular Surface Hydrophilicity

In this study anodization and annealing condition are optimized to fabricate nanotubular surface which is able to maintain its hydrophilicity over time — anti-aging surface. Our results indicate that anodization voltage and annealing temperature affect surface ability to maintain its hydrophilicity. Water contact angle measurements show hydrophilicty is sharply decreased after annealing regardless of annealing and anodization conditions. Non-anodized and 20 V anodized samples lose their hydrophilicity after 11 days of aging in air, while 60 V anodized samples are able to maintain their hydrophilicity after this period.

Atomic Layer Deposition in Bio-Nanotechnology: A Brief Overview

Atomic layer deposition (ALD) is a technique increasingly used in nanotechnology and ultrathin film deposition; it is ideal for films in the nanometer and Angstrom length scales. ALD can effectively be used to modify the surface chemistry and functionalization of engineering-related and biologically important surfaces. It can also be used to alter the mechanical, electrical, chemical, and other properties of materials that are increasingly used in biomedical engineering and biological sciences. ALD is a relatively new technique for optimizing materials for use in bio-nanotechnology. Here, after a brief review of the more widely used modes of ALD and a few of its applications in biotechnology, selected results that show the potential of ALD in bio-nanotechnology are presented. ALD seems to be a promising means for tuning the hydrophilicity/hydrophobicity characteristics of biomedical surfaces, forming conformal ultrathin coatings with desirable properties on biomedical substrates with a high aspect ratio, tuning the antibacterial properties of substrate surfaces of interest, and yielding multifunctional biomaterials for medical implants and other devices.