Asier Vallejo

Intersex condition and molecular markers of endocrine disruption in relation with burdens of emerging pollutants in thicklip grey mullets (Chelon labrosus) from Basque estuaries (South-East Bay of Biscay).

Endocrine disrupting chemicals (EDCs) interfere with the functioning of the endocrine system, causing reproductive and developmental disturbances in aquatic wildlife. Appearance of intersex gonads and elevated plasma levels of vitellogenin in male fish are well known biomarkers of exposure to xenoestrogenic EDCs. In the present study, intersex condition and transcription levels of vtg and cyp19a1b were assessed in five thicklip grey mullet populations from the Basque coast (Bay of Biscay). Levels of EDCs (estrogenic hormones, polycyclic musks, bisphenol-A, phthalates, alkylphenols and pesticides) were determined in water and fish bile. Intersex gonads were observed in three out of five mullet populations. Vtg and cyp19a1b were up-regulated in mullet populations with relatively higher EDCs load. Phthalates and pesticides were the most abundant EDCs in bile, followed by alkylphenols, musks, bisphenol-A and estrogenic hormones. Statistically significant correlations were found between concentrations of individual and total EDCs in bile and water samples and transcription levels of vtg and cyp19a1b.

Solid-phase extraction combined with large volume injection-programmable temperature vaporization-gas chromatography-mass spectrometry for the multiresidue determination of priority and emerging organic pollutants in wastewater.

In the present work the simultaneous extraction for the multiresidue determination in wastewater samples of organic compounds such as polychlorinated biphenyls (PCBs), polybrominated biphenyls (PBBs), pesticides, polycyclic aromatic hydrocarbons (PAHs), phthalate esters (PEs), alkylphenols (APs), bisphenol A (BPA) or hormones included in different lists of priority and emerging pollutants because of their action as endocrine disrupting compounds (EDCs) was developed. Different solid phase extraction (SPE) variables such as the nature of the solid phase (Oasis-HLC, C18 and Lichrolut), the sample volume, the addition of MeOH and NaCl, the pH of the water phase and the volume of the eluent solvent were optimized in order to analyze simultaneously the priority and emerging families of pollutants mentioned above. Good recoveries were obtained for Milli-Q water (80-120%), however, since the use of deuterated analogues and dilution of the sample did not correct the matrix effect, additional SPE clean-up step using Florisil® cartridges was necessary to obtain good results for wastewater samples (80-125%). In order to improve the limits of detection (LODs), large volume injection (LVI) using programmable temperature vaporizer (PTV) coupled to gas chromatography-mass spectrometry (GC-MS) was also optimized. Since analytes losses in the case of the most volatile congeners occurred during the derivatization step and no separation of the derivatized and the non-derivatized analytes was possible during SPE elution, two different injections were optimized for each analyte group. LODs were in good agreement with those found in the literature and relative standard deviations (RSDs) were in the 10-25% range for Milli-Q and 12-30% for wastewater samples. The method was finally applied to the determination of target analytes in three different wastewater treatment plants (WWTPs, Bakio, Gernika and Galindo (Spain)) and in one water purification plant (WPP) in Zornotza (Spain).

Microencapsulation and storage stability of polyphenols from Vitis vinifera grape wastes

Wine production wastes are an interesting source of natural polyphenols. In this work, wine wastes extracts were encapsulated through vibration nozzle microencapsulation using sodium alginate as polymer and calcium chloride as hardening reagent. An experimental design approach was used to obtain calcium-alginate microbeads with high polyphenol content and good morphological features. In this way, the effect of pressure, frequency, voltage and the distance to the gelling bath were optimized for two nozzles of 150 and 300 μm. Long-term stability of the microbeads was studied for 6 months taking into account different storage conditions: temperatures (4 °C and room temperature), in darkness and in presence of light, and the addition of chitosan to the gelling bath. Encapsulated polyphenols were found to be much more stable compared to free polyphenols regardless the encapsulation procedure and storage conditions. Moreover, slightly lower degradation rates were obtained when chitosan was added to the gelling bath.

Calibration and field test of the Polar Organic Chemical Integrative Samplers for the determination of 15 endocrine disrupting compounds in wastewater and river water with special focus on performance reference compounds (PRC).

In this work, home-made Polar Organic Chemical Integrative Samplers (POCIS) were studied for passive sampling of 15 endocrine disrupting compounds (4 alkylphenols and steroid hormones) in influent and effluent samples of wastewater treatment plants (WWTPs) as well as up- and downstream of the receiving river water. POCIS calibration at laboratory conditions was carried out using a continuous-flow calibration system. The influence of the exposure position of the POCIS within the calibration device, horizontal or vertical, to the water flow direction was evaluated. While the sampling rates of most of the target substances were not affected by the sampler position, for cis-ADT, E1, E2 and E3, the vertical position provided the highest analyte accumulation. Hence, the POCIS samplers were preferably exposed vertical to the water flow in overall experiments. Using the continuous-flow calibration device, lab-based sampling rates were determined for all the target compounds (RSBPA = 0.0326 L/d; RScisADT = 0.0800 L/d, RSE1 = 0.0398 L/d, RSEQ = 0.0516 L/d, RSTT = 0.0745 L/d, RSE2 = 0.0585 L/d, RSEE2 = 0.0406 L/d, RSNT = 0.0846 L/d, RSPG = 0.0478 L/d and RSE3 = 0.1468 L/d), except for DES, MeEE2, 4tOP, 4OP, 4NPs, where the uptake after 14 days POCIS exposure was found to be insignificant or indicated a no linear behaviour. Recoveries from POCIS extractions were in the range between 71 and 152% for most of the target analytes except for DES and E3 with around 59%. Good precision of the sampling procedure up till 20% was observed and limits of detection were at ng/L level. Two deuterated compounds ([(2)H3]-E2 and [(2)H4]-EQ) were successfully tested as performance reference compounds (PRC, [Formula: see text] = 0.0507 L/d and [Formula: see text] = 0.0543 L/d)). Finally, the POCIS samplers were tested for monitoring EDCs at two wastewater treatment plants, in Halle and Leipzig (Germany). BPA, E1, EQ, E2, MeEE2, NT, EE2, PG and E3 were quantified and their time-weighted average concentrations calculated on the basis of the lab-derived sampling rates were compared with the results based on conventional grab samples. While the influent concentration of BPA, cisADT, E1, TT, PG, EE2 reached the μg/L level, the rest of the target analytes were determined at ng/L. The analyte concentrations in the effluent never exceed ng/L level except for BPA. The concentration determined by spot sampling was partially lower (BPA, E1, TT) or comparable (EQ, E2, EE2, PG, E3) to the concentration obtained by POCIS using performance reference compounds (PRC).

Membrane assisted solvent extraction coupled to large volume injection-gas chromatography–mass spectrometry for trace analysis of synthetic musks in environmental water samples

This work describes the optimisation, validation and application of membrane assisted solvent extraction (MASE) together with a large volume injection (LVI) in a programmable temperature vaporisation (PTV) injector coupled to gas chromatography-mass spectrometry (GC-MS) for the quantification of ten synthetic musk fragrances (musks) in surface and wastewater samples. Regarding the MASE, musks were extracted from 150 mL of aqueous samples to 200 μL of n-hexane hold in home-made low density polyethylene (LDPE) bags. The extraction took 240 min and the performance of the method made possible the direct analysis of the extracts by LVI-PTV-GC-MS without needing any further treatment and avoiding losses of analytes. During the optimisation of LVI-PTV set-up, the response surfaces of every analyte signal against the cryo-focussing temperature, injection speed and vent time were built. Finally, the figures of merit of the whole procedure allowed the analysis of most of the musks owing to the low method detection limits (between 4 and 25 ng L⁻¹) and good precisions (<20%). In fact, this method was successfully applied to the analysis of musks in surface and wastewater samples. Galaxolide and tonalide are the main two synthetic musks observed in most of the analysed environmental water samples.

Microextraction with polyethersulfone for bisphenol-A, alkylphenols and hormones determination in water samples by means of gas chromatography–mass spectrometry and liquid chromatography–tandem mass spectrometry analysis

In the present work, the suitability of polyethersulfone (PES) tube was assessed for the simultaneous sorptive microextraction of commonly found endocrine disrupting compounds in natural waters such as bisphenol-A (BPA), nonylphenol technical mixture (NP mix), 4-tert-octylphenol (4tOP), 4-n-octylphenol (4-nOP), 17β-estradiol (E2) and 17α-ethynilestradiol (EE2). After the concentration of target compounds in the PES polymer, the analytes were recovered soaking the polymer with a suitable solvent (ethyl acetate or methanol), derivatized using N,O-bis(trimethylsilyl)trifluoroacetamide with 1% of trimethylchlorosilane (BSTFA+1% TMCS) and determined by gas chromatography-mass spectrometry (GC-MS). The analysis was also performed without derivatization step by means of liquid chromatography-tandem mass spectrometry (LC-MS/MS). Extraction parameters (addition of MeOH, ionic strength, extraction speed and time and desorption time) were evaluated and the optimum conditions were fixed as follows: 150 mL water samples containing a 10% (w/v) of sodium chloride and using 5 tubular PES sorbent fibers (1.5 cm length×0.7 mm o.d.). Equilibrium conditions were achieved after 9 h, with absolute extraction efficiencies ranging from 27 to 56%. On the whole, good apparent recoveries were achieved (68-103% and 81-122% for GC-MS and LC-MS/MS, respectively) using deuterated analogues as surrogates. Achieved quantification limits (LOQs) varied between 2-154 ng/L and 2-63 ng/L for all the compounds using GC-MS and LC-MS/MS, respectively. The effect of organic matter was evaluated previous to apply the final method to the analysis of estuarine and wastewater real samples. The comparison of both methods showed that overall, PES-LC-MS/MS provided shorter sample preparation time and better LODs, but PES-silylation-GC-MS allowed the simultaneous determination of all the studied compounds with adequate repeatability and accuracy.

Optimization of large volume injection-programmable temperature vaporization-gas chromatography-mass spectrometry analysis for the determination of estrogenic compounds in environmental samples.

Large volume injection-programmable temperature vaporization-gas chromatography-mass spectrometry (LVI-PTV-GC-MS) was optimized for the determination of estrone (E1), 17β-estradiol (E2), 17α-ethynyl estradiol (EE2), mestranol (MeEE2) and estriol (E3) for their determination in environmental samples (estuarine water, wastewater, fish bile and fish homogenate) after derivatization with 25 μL (BSTFA+1% TMCS) and 125 μL of pyridine. Experimental designs such as Plackett-Burman (PBD) and central composite designs (CCDs) were used to optimize the LVI-PTV variables (cryo-focusing temperature, vent time, vent flow, vent pressure, injection volume, purge flow to split vent, splitless time and injection speed). Optimized conditions were as follows: 45 μL of n-hexane extract are injected at 60°C and 6 μL/s with a vent flow and a vent pressure of 50 mL/min and 7.7 psi, respectively, during 5 min; then the split valve is closed for 1.5 min and afterwards the injector is cleaned at 100 mL/min before the next injection. The method was applied to the determination of estrogenic compounds in environmental samples such as estuarine water, wastewater, and fish homogenate and bile. Limits of detection (0.04-0.15 ng/L for water samples, 0.04-0.67 ng/g for fish bile and 0.1-7.5 ng for fish homogenate) obtained were approx. ten times lower than those obtained by means of a common split/splitless inlet.

Optimization of comprehensive two dimensional gas chromatography-flame ionization detection–quadrupole mass spectrometry for the separation of octyl- and nonylphenol isomers

In the present work, the separation of complex nonylphenol technical mixtures has been optimized using comprehensive two-dimensional gas chromatography coupled with a flame ionization detector and quadrupole mass spectrometer (GC×GC-qMS), using valve-based modulator. The optimization of GC×GC-qMS has been carried out using experimental designs and the optimal separation was obtained at the following conditions: 1st column flow: 1mL/min; 2nd column flow: 17.75 mL/min, oven temperature ramp: 1°C/min, modulation period: 1.5s and discharge time: 0.12s. These values have been used to determinate the previously synthesized 22OP, 33OP, 363NP and 22NP isomers in two different nonylphenol technical mixtures. Percentages obtained were as follows: 4.86% and 0.59% for 22OP, 4.91% and 2.82% for 33OP, 11.79% and 7.71% for 363NP and 2.28% and 1.98% for 22NP, in Fluka and Aldrich mixtures, respectively. The values obtained for NP isomers are in good agreement with the literature.

In-port derivatization after sorptive extractions

Derivatization is necessary when analysis of polar compounds containing hydroxyl, carboxylic acid, amine or thiol functional groups is accomplished by gas chromatography (GC), in order to improve peak symmetry, peak separation and detector response. Derivatization can be performed off-line in a reaction vessel that is separated from the GC analysis hardware. However, on-line derivatization can eliminate time-consuming sample-processing steps, decrease the amount of valuable and/or toxic reagents and solvents that are used off-line, as well as increase the speed and efficiency of the analysis performed. The present work revises on-line in-port derivatizations where the derivatization reaction is simultaneously carried out with the analysis step by injecting the sample/reagent mixture directly into the hot GC inlet after a sorptive extraction step. Sorptive extractions revised range from the more classical solid-phase extraction (SPE) to the microextraction approaches, including solid-phase microextraction (SPME) and stir-bar sorptive extraction (SBSE) applications, as well as liquid-phase microextraction (LPME) or microextraction by packed sorbent (MEPS).

Ultrasonic‐assisted derivatization of estrogenic compounds in a cup horn booster and determination by GC‐MS

Cup horn boosters are miniaturized ultrasound baths that maximize efficiency and precision. The optimization of an ultrasonic-assisted derivatization step by means of a cup horn booster and the determination of estrone, 17beta-estradiol, estriol, 17alpha-ethynyl estradiol and mestranol was developed by GC-MS. Different derivatization reagents and solvents were studied for maximizing the di-derivatization of 17alpha-ethynyl estradiol under ultrasound energy. Only N,O-bis(trimethylsilyl)trifluoroacetamide with 1% of trimethylchlorosilane in pyridine gave satisfactory results and this mixture was further used in the optimization of the ultrasound assisted derivatization. The experiment designs included sonication time (1-10 min), sonication power (20-80%), sonication cycles (1-9), derivatization reagent volume (25-125 microL) and solvent volume (25-125 microL). Once the optimum conditions were fixed, the effect of organic matter and the frequency of the water bath change were studied. Finally, the validation of the analytical method was carried out using spiked natural and synthetic waters. Recoveries (natural (138-70%) and synthetic (112-89%)), the LODs (0.35-1.66 ng/L), and LOQs (1.16-5.52 ng/L) and the precision (0.2-5.3%) of the method were studied. This is the first work in the literature where a cup horn booster is used with the aim of minimizing derivatization time during the determination of estrogenic compounds.