Ataís Bacchi

Effect of framework material and vertical misfit on stress distribution in implant-supported partial prosthesis under load application: 3-D finite element analysis

Abstract Objective. This study evaluated the influence of framework material and vertical misfit on stress created in an implant-supported partial prosthesis under load application. Materials and methods. The posterior part of a severely reabsorbed jaw with a fixed partial prosthesis above two osseointegrated titanium implants at the place of the second premolar and second molar was modeled using SolidWorks 2010 software. Finite element models were obtained by importing the solid model into an ANSYS Workbench 11 simulation. The models were divided into 15 groups according to their prosthetic framework material (type IV gold alloy, silver-palladium alloy, commercially pure titanium, cobalt-chromium alloy or zirconia) and vertical misfit level (10 µm, 50 µm and 100 µm). After settlement of the prosthesis with the closure of the misfit, simultaneous loads of 110 N vertical and 15 N horizontal were applied on the occlusal and lingual faces of each tooth, respectively. The data was evaluated using Maximum Principal Stress (framework, porcelain veneer and bone tissue) and a von Mises Stress (retention screw) provided by the software. Results. As a result, stiffer frameworks presented higher stress concentrations; however, these frameworks led to lower stresses in the porcelain veneer, the retention screw (faced to 10 µm and 50 µm of the misfit) and the peri-implant bone tissues. Conclusion. The increase in the vertical misfit resulted in stress values increasing in all of the prosthetic structures and peri-implant bone tissues. The framework material and vertical misfit level presented a relevant influence on the stresses for all of the structures evaluated.

Surface Treatments for Repair of Feldspathic, Leucite - and Lithium Disilicate-Reinforced Glass Ceramics Using Composite Resin

The aim of this study was to evaluate the efficacy of different surface conditioning methods on the microtensile bond strength of a restorative composite repair in three types of dental ceramics: lithium disilicate-reinforced, leucite-reinforced and feldspathic. Twelve blocks were sintered for each type of ceramic (n=3) and stored for 3 months in distilled water at 37 °C. The bonding surface of ceramics was abraded with 600-grit SiC paper. Surface treatments for each ceramic were: GC (control) - none; GDB - diamond bur #30 µm; GHF - hydrofluoric acid (10%); GT- tribochemical silica coating (45-μm size particles). Treatments were followed by cleaning with phosphoric acid 37% for 20 s + silane + adhesive. The composite resin was used as restorative material. After repair, samples were subjected to thermocycled ageing (10,000 cycles between 5 °C and 55 °C for 30 s). Thereafter, the samples were sectioned into 1.0 mm2 sticks and tested for microtensile bond strength with 0.5 mm/min crosshead speed. Data were compared by two-way ANOVA and Tukeys test (α=0.05). The superficial wear with diamond bur proved to be suitable for feldspathic porcelain and for leucite-reinforced glass ceramic while hydrofluoric acid-etching is indicated for repairs in lithium disilicate-reinforced ceramic; tribochemical silica coating is applicable to leucite-reinforced ceramic. Predominance of adhesive failures was observed (>85% in all groups). In conclusion, the success of surface treatments depends on the type of ceramic to be repaired.

Thio-urethane oligomers improve the properties of light-cured resin cements

Thio-urethanes were synthesized by combining 1,6-hexanediol-diissocyante (aliphatic) with pentaerythritol tetra-3-mercaptopropionate (PETMP) or 1,3-bis(1-isocyanato-1-methylethyl)benzene (aromatic) with trimethylol-tris-3-mercaptopropionate (TMP), at 1:2 isocyanate:thiol, leaving pendant thiols. Oligomers were added at 10-30 phr to BisGMA-UDMA-TEGDMA (5:3:2, BUT). 25 wt% silanated inorganic fillers were added. Commercial cement (Relyx Veneer, 3M-ESPE) was also evaluated with 10-20 phr of aromatic oligomer. Near-IR was used to follow methacrylate conversion (DC) and rate of polymerization (Rpmax). Mechanical properties were evaluated in three-point bending (ISO 4049) for flexural strength/modulus (FS/FM, and toughness), and notched specimens (ASTM Standard E399-90) for fracture toughness (KIC). Polymerization stress (PS) was measured on the Bioman. Volumetric shrinkage (VS, %) was measured with the bonded disk technique. Results were analyzed with ANOVA/Tukeys test (α=5%). In general terms, for BUT cements, conversion and mechanical properties in flexure increased for selected groups with the addition of thio-urethane oligomers. The aromatic versions resulted in greater FS/FM than aliphatic. Fracture toughness increased by two-fold in the experimental groups (from 1.17 ± 0.36 MPam(1/2) to around 3.23 ± 0.22 MPam(1/2)). Rpmax decreased with the addition of thio-urethanes, though the vitrification point was not statistically different from the control. VS and PS decreased with both oligomers. For the commercial cement, 20 phr of oligomer increased DC, vitrification, reduced Rpmax and also significantly increased KIC, and reduced PS and FM. Thio-urethane oligomers were shown to favorably modify conventional dimethacrylate networks. Significant reductions in polymerization stress were achieved at the same time conversion and fracture toughness increased.

Influence of different mucosal resiliency and denture reline on stress distribution in peri-implant bone tissue during osseointegration. A three-dimensional finite element analysis

OBJECTIVE The aim of this study was to evaluate the influence of mucosal properties and relining material on the stress distribution in peri-implant bone tissue during masticatory function with a conventional complete denture during the healing period through finite element analysis. MATERIALS AND METHODS Three-dimensional models of a severely resorbed mandible with two recently placed implants in the anterior region were created and divided into the following situations: (i) conventional complete denture and (ii) relined denture with soft lining material. The mucosal tissue properties were divided into soft, resilient and hard. The models were exported to mechanical simulation software; two simulations were carried out with a load at the lower right canine (35 N) and the lower right first molar (50 N). Data were qualitatively evaluated using Maximum Principal Stress, in MPa, given by the software. RESULTS All models showed stress concentrations in the cortical bone corresponding to the cervical part of the implant. The mucosal properties influenced the stress in peri-implant bone tissue showing a different performance according to the denture base material. The simulations with relined dentures showed lower values of stress concentration than conventional ones. CONCLUSIONS It seems that the mucosal properties and denture reline have a high influence on the stress distribution in the peri-implant bone during the healing period.

Characterization of methacrylate-based composites containing thio-urethane oligomers

OBJECTIVE To evaluate the ability of thio-urethane oligomers to improve the properties of restorative composite resins. METHODS Oligomers were synthesized by combining 1,6-hexanediol-diissocyante (aliphatic) with pentaerythritol tetra-3-mercaptopropionate (PETMP) or 1,3-bis(1-isocyanato-1-methylethyl)benzene (aromatic) with trimethylol-tris-3-mercaptopropionate (TMP), at 1:2 isocyanate:thiol, leaving pendant thiols. Oligomers were added at 0-20 wt% to BisGMA-TEGDMA (70-30 wt%). Silanated inorganic fillers were added (70 wt%). Materials were photoactivated at 800 mW/cm(2) filtered to 320-500 nm. Near-IR was used to follow degree of methacrylate conversion (DC). Mechanical properties were evaluated in three-point bending with 2 mm × 2 mm × 25 mm bars for flexural strength/modulus and toughness (FS/E, and T) according to ISO 4049, and 2 mm × 5 mm × 25 mm notched specimens for fracture toughness (KIC). Polymerization stress (PS) was measured on the Bioman. Results were analyzed with ANOVA/Tukeys test (α=5%). RESULTS Significant increase in DC was observed in thio-urethane-containing materials especially for the group with 20 wt% of aliphatic version. Materials composed by oligomers also promoted higher FS, E, and KIC in comparison to controls irrespective of thio-urethane type. A significant increase in toughness was detected by ANOVA, but not distinguished in the groups. The PS was significantly reduced by the presence of thio-urethane for almost all groups. CONCLUSIONS The use of thio-urethane oligomer to compose methacrylate-based restorative composite promote increase in DC, FS, E and KIC while significant reduces PS. SIGNIFICANCE A simple additive was shown to reduce stress while increasing convrersion and mechanical properties, mainly fracture toughness. This has he potential of increasing the service life of dental composites, without changing current operatory procedures.

Repair bond strength in aged methacrylate- and silorane-based composites.

PURPOSE To evaluate the tensile bond strength at repaired interfaces of aged dental composites, either dimethacrylate- or silorane-based, when subjected to different surface treatments. MATERIALS AND METHODS The composites used were Filtek P60 (methacrylate-based, 3M ESPE) and Filtek P90 (silorane-based, 3M ESPE), of which 50 slabs were stored for 6 months at 37°C. The surface of adhesion was abraded with a 600-grit silicone paper and the slabs repaired with the respective composite, according to the following surface treatment protocols: G1: no treatment; G2: adhesive application; G3: silane + adhesive; G4: sandblasting (Al2O3) + adhesive; G5: sandblasting (Al2O3) + silane + adhesive. After 24-h storage in distilled water at 37°C, tensile bond strength (TBS) was determined in a universal testing machine (Instron 4411) at a crosshead speed of 0.5 mm/min. The original data were submitted to two-way ANOVA and Tukeys test (α = 5%). RESULTS The methacrylate-based composite presented a statistically significantly higher repair potential than did the silorane-based resin (p = 0.0002). Of the surface treatments for the silorane-based composite, aluminum-oxide air abrasion and adhesive (18.5 ± 3.3MPa) provided higher bond strength than only adhesive application or the control group without surface treatment. For Filtek P60, the control without treatment presented lower repair strength than all other groups with surface treatments, which were statistically similar to each other. The interaction between the factors resin composite and surface treatment was significant (p = 0.002). CONCLUSION For aged silorane-based materials, repairs were considered successful after sandblasting (Al2O3) and adhesive application. For methacrylate resin, repair was successful with all surface treatments tested.

Influence of surface treatments to repair recent fillings of silorane-and methacrylate-based composites

Purpose: The aim of this study was to evaluate the tensile bond strength (TBS) of repairs in recent fillings of methacrylate- (MBC) or silorane-based composites (SBC) subsequent to different surface treatments. Materials and Methods: Fifty slabs of Filtek P60 (3M ESPE, St Paul, USA) and Filtek P90 (3M ESPE) were stored for 10 days in distilled water at 37°C. The surface of adhesion was abraded with a 600-grit silicone paper and repaired using each respective composite: G1, no treatment (control); G2, application of adhesive; G3, application of silane and adhesive; G4, sandblasting (Al2O3) and adhesive; and G5, sandblasting (Al2O3), silane, and adhesive. Further 10 slabs of each composite were also evaluated for cohesive strength (G6). After 30 days immersion in distilled water at 37°C, the TBS was determined. Results: TBS results were higher for MBC than for SBC (P = 0.00012). The experimental groups were similar for SBC and the TBS was 27% of its cohesive strength. For P60, sandblasting significantly improved the TBS compared to other groups. With MBC, G4 and G5, the TBS was approximately 47% of its cohesive strength. Conclusion: Sandblasting (Al2O3) improves the repair-strength of MBC, whilst for the SBC all treatments succeed. MBC presents higher repair strength than SBC.

Loosening torque of prosthetic screws in metal-ceramic or metal-acrylic resin implant-supported dentures with different misfit levels.

The aim of this study was to evaluate the effect of the prosthesis material (metal-acrylic resin or metal-ceramic) on loosening torque of the prosthetic screws in an implant-supported mandibular denture under two levels of vertical misfit. Ten frameworks were fabricated with commercially pure titanium, and five of them received acrylic resin and acrylic artificial teeth as veneering material and the other five were veneered with porcelain. Two levels of vertical fit were also created by fabricating 20 cast models to obtain four experimental groups according to the prosthesis material and misfit: Group 1 (metal-acrylic resin prosthesis with a passive fit); Group 2 (metal-acrylic resin prosthesis with a non-passive fit); Group 3 (metal-ceramic prosthesis with a passive fit); and Group 4 (metal-ceramic prosthesis with a non-passive fit). Two hundred prosthetic titanium-alloy screws were divided in 40 sets (five screws per set, n=10). After 24h, the loosening torque of the screws was evaluated using a digital torque meter. The results were submitted to two-way ANOVA analysis of variance followed by a Tukeys test (α=0.05). The mean values and standard deviations for each group were G1=7.05 (1.64), G2=5.52 (0.90), G3=6.46 (1.34), and G4=4.35 (0.99). Overall, the prosthesis material and misfit factors showed a statistically significant influence on the loosening torque (p<0.05). Metal-ceramic prosthesis and misfits decreased the loosening of the torque of the prosthetic screws.

Loosening torque of Universal Abutment screws after cyclic loading: influence of tightening technique and screw coating

PURPOSE The purpose of this study was to evaluate the influence of tightening technique and the screw coating on the loosening torque of screws used for Universal Abutment fixation after cyclic loading. MATERIALS AND METHODS Forty implants (Titamax Ti Cortical, HE, Neodent) (n=10) were submerged in acrylic resin and four tightening techniques for Universal Abutment fixation were evaluated: A - torque with 32 Ncm (control); B - torque with 32 Ncm holding the torque meter for 20 seconds; C - torque with 32 Ncm and retorque after 10 minutes; D - torque (32 Ncm) holding the torque meter for 20 seconds and retorque after 10 minutes as initially. Samples were divided into subgroups according to the screw used: conventional titanium screw or diamond like carbon-coated (DLC) screw. Metallic crowns were fabricated for each abutment. Samples were submitted to cyclic loading at 106 cycles and 130 N of force. Data were analyzed by two-way ANOVA and Tukeys test (5%). RESULTS The tightening technique did not show significant influence on the loosening torque of screws (P=.509). Conventional titanium screws showed significant higher loosening torque values than DLC (P=.000). CONCLUSION The use of conventional titanium screw is more important than the tightening techniques employed in this study to provide long-term stability to Universal Abutment screws.

Influence of post-thickness and material on the fracture strength of teeth with reduced coronal structure.

Purpose: To evaluate the fracture strength of endodontically treated teeth with reduced coronal structure reinforced with glass-fiber posts and cast posts and core (nickel–chromium alloy) with different thickness. Materials and Methods: Forty maxillary central incisors were sectioned at 1 mm of the cementoenamel junction and endodontically treated. The teeth were divided into four groups (n = 10) and restored with cast post and core and glass-fiber posts with diameters of 1.5 mm and 1.1 mm. The fracture strength was evaluated using a Universal Testing Machine (Instron 1144) at 45° of angulation. The results were submitted to analysis of variance two-way and Tukeys test (P < 0.05). The failure mode was also evaluated. Results: Cast post and core were statistically superior to the glass-fiber posts with the self-post diameter (P = 0.001). When the self-post material was considered, no significant difference was observed between the two post-diameters (P = 0.749). The glass-fiber post-groups presented more fractures in the cervical third than the cast post and core groups. Conclusion: Teeth restored with cast post and cores present higher fracture strength than those reinforced with glass-fiber posts. An increased post-thickness does not increase the fracture strength. Glass-fiber posts lead to less severe fractures.