Bilgen Osman

Magnetic vinylphenyl boronic acid microparticles for Cr(VI) adsorption: kinetic, isotherm and thermodynamic studies.

Magnetic vinylphenyl boronic acid microparticles, poly(ethylene glycol dimethacrylate(EG)-vinylphenyl boronic acid(VPBA)) [m-poly(EG-VPBA)], produced by suspension polymerization and characterized, was found to be an efficient solid polymer for Cr(VI) adsorption. The m-poly(EG-VPBA) microparticles were prepared by copolymerizing of ethylene glycol dimethylacrylate (EG) with 4-vinyl phenyl boronic acid (VPBA). The m-poly(EG-VPBA) microparticles were characterized by N2 adsorption/desorption isotherms, electron spin resonance (ESR), X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA), elemental analysis, scanning electron microscope (SEM) and swelling studies. The m-poly(EG-VPBA) microparticles were used at adsorbent/Cr(VI) ion ratios. The influence of pH, Cr(VI) initial concentration, temperature of the removal process was investigated. The maximum removal of Cr(VI) was observed at pH 2. Langmuir isotherm and Dubinin-Radushkvich isotherm were found to better fit the experiment data rather than Fruendlich isotherm. The kinetics of the adsorption process of Cr(VI) on the m-poly(EG-VPBA) microparticles were investigated using the pseudo first-order, pseudo-second-order, Ritch-second-order and intraparticle diffusion models, results showed that the pseudo-second order equation model provided the best correlation with the experimental results. The thermodynamic parameters (free energy change, ΔG(0) enthalpy change, ΔH(0); and entropy change, ΔS(0)) for the adsorption have been evaluated.

Microcontact imprinted surface plasmon resonance sensor for myoglobin detection

In this study, we prepared surface plasmon resonance (SPR) sensor using the molecular imprinting technique for myoglobin detection in human serum. For this purpose, we synthesized myoglobin imprinted poly(hydroxyethyl methacrylate-N-methacryloyl-l-tryptophan methyl ester) [poly(HEMA-MATrp)] nanofilm on the surface of SPR sensor. We also synthesized non-imprinted poly(HEMA-MATrp) nanofilm without myoglobin for the control experiments. The SPR sensor was characterized with contact angle measurements, atomic force microscopy, X-ray photoelectron spectroscopy, and ellipsometry. We investigated the effectiveness of the sensor using the SPR system. We evaluated the ability of SPR sensor to sense myoglobin with myoglobin solutions (pH7.4, phosphate buffer) in different concentration range and in the serum taken from a patient with acute myocardial infarction. We found that the Langmuir adsorption model was the most suitable for the sensor system. The detection limit was 87.6 ng/mL. In order to show the selectivity of the SPR sensor, we investigated the competitive detection of myoglobin, lysozyme, cytochrome c and bovine serum albumin. The results showed that the SPR sensor has high selectivity and sensitivity for myoglobin.

Removal of diethyl phthalate from aqueous phase using magnetic poly(EGDMA–VP) beads

The barium hexaferrite (BaFe(12)O(19)) containing magnetic poly(ethylene glycol dimethacrylate-vinyl pyridine), (mag-poly(EGDMA-VP)) beads (average diameter=53-212 μm) were synthesized and characterized. Their use as an adsorbent in the removal of diethyl phthalate (DEP) from an aqueous solution was investigated. The mag-poly(EGDMA-VP) beads were prepared by copolymerizing of 4-vinyl pyridine (VP) with ethylene glycol dimethacrylate (EGDMA). The mag-poly(EGDMA-VP) beads were characterized by N(2) adsorption/desorption isotherms (BET), vibrating sample magnetometer (VSM), X-ray powder diffraction (XRD), elemental analysis, scanning electron microscope (SEM) and swelling studies. At a fixed solid/solution ratio, the various factors affecting the adsorption of DEP from aqueous solutions such as pH, initial concentration, contact time and temperature were analyzed. The maximum DEP adsorption capacity of the mag-poly(EGDMA-VP) beads was determined as 98.9 mg/g at pH 3.0, 25°C. All the isotherm data can be fitted with both the Langmuir and the Dubinin-Radushkevich isotherm models. The pseudo first-order, pseudo-second-order, Ritch-second-order and intraparticle diffusion models were used to describe the adsorption kinetics. The thermodynamic parameters obtained indicated the exothermic nature of the adsorption. The DEP adsorption capacity did not change after 10 batch successive reactions, demonstrating the usefulness of the magnetic beads in applications.

Immobilization of Glucoamylase onto Lewis Metal Ion Chelated Magnetic Affinity Sorbent: Kinetic, Isotherm and Thermodynamic Studies

In this study, magnetic metal-chelate beads, m-poly(ethylene glycol dimethacrylate-vinyl imidazole) [m-poly(EGDMA–VIM)] with an average diameter 150–200 μm was synthesized by copolymerizing ethylene glycol dimethacrylate (EGDMA) with vinyl imidazole (VIM). The spesific surface area of the m-poly(EGDMA–VIM) beads was found 63.1 m2/g. Cu2+ ions were chelated on the m-poly(EGDMA–VIM) beads and used in immobilization of Aspergillus niger glucoamylase in a batch system. The maximum glucoamylase adsorption capacity of the m-poly(EGDMA–VIM)–Cu2+ beads was observed as 120 mg/g at pH 6.5. The optimum pH for free and m-poly(EGDMA–VIM)–Cu2+ immobilized glucoamylase were found 4.0 and 4.5, respectively. The optimum temperature of glucoamylase was not changed after immobilization and determined as 60 o C for free and immobilized enzyme preparations. The glucoamylase adsorption capacity and adsorbed enzyme activity slightly decreased after 10 batch successive reactions, demonstrating the usefulness of the enzyme-loaded beads in biocatalytic applications. Storage stability was found to increase with immobilization. The effect of various experimental parameters such as pH, glucoamylase concentration, contact time and temperature in aqueous solution were also investigated. Adsorption isotherm obtained for m-poly(EGDMA–VIM)–Cu2+ was consistent with Langmuir model. Kinetic studies showed that the adsorption process agreed with both the pseudo-second-order kinetic model and the modified Ritchies-second-order kinetic model. Various thermodynamic parameters, free energy (ΔG 0), enthalpy (ΔH 0) and entropy (ΔS 0), were also calculated and the results showed that the adsorption process strongly depended on temperature of medium.

Poly(hydroxyethyl methacrylate) based affinity membranes for in vitro removal of anti-dsDNA antibodies from SLE plasma

The preparation of polymeric membrane using affinity technology for application in blood filtration devices is described here. DNA attached poly(hydroxyethyl methacrylate) (PHEMA) based microporous affinity membrane was prepared for selective removal of anti-dsDNA antibodies from systemic lupus erythematosus (SLE) patient plasma in in vitro. In order to further increase blood-compatibility of affinity membrane, aminoacid based comonomer N-methacryloyl-L-alanine (MAAL) was included in the polymerization recipe. PHEMAAL membrane was produced by a photopolymerization technique and then characterized by swelling tests and scanning electron microscope (SEM) studies. Blood-compatibility tests were also performed. The water swelling ratio of PHEMAAL membrane increased significantly (133.2%) compared with PHEMA (58%). PHEMAAL membrane has large pores around in the range of 5-10 microm. All the clotting times increased when compared with PHEMA membrane. Loss of platelets and leukocytes was very low. DNA loading was 7.8 mg/g. There was a very low anti-dsDNA-antibody adsorption onto the plain PHEMAAL membrane, about 78 IU/g. The PHEMAAL-DNA membrane adsorbed anti-dsDNA-antibody in the range of 10-68 x 10(3)IU/g from SLE plasma. Anti-dsDNA-antibody concentration decreased significantly from 875 to 144 IU/ml with the time. Anti-dsDNA-antibodies could be repeatedly adsorbed and eluted without noticeable loss in the anti-dsDNA-antibody adsorption amount.

Assesment of dimethyl phthalate removal from aqueous phase using barium hexaferrite containing magnetic beads.

The barium hexaferrite (BaFe(12)O(19)) containing magnetic poly (ethylene glycol dimethacrylate-vinyl pyridine; mag-poly [EGDMA-VP]) beads (average diameter=53-212 μm) were synthesized and characterized. Their use as an adsorbent in the removal of dimethyl phthalate (DMP) from an aqueous solution was investigated. The mag-poly (EGDMA-VP) beads were prepared by copolymerizing of 4-vinyl pyridine (VP) with ethylene glycol dimethacrylate (EGDMA). The mag-poly (EGDMA-VP) beads were characterized by N(2) adsorption/desorption isotherms (BET), vibrating sample magnetometer (VSM), X-ray powder diffraction (XRD), elemental analysis, scanning electron microscope (SEM), and swelling studies. At a fixed solid/solution ratio, the various factors affecting the adsorption of DMP from aqueous solutions such as pH, initial concentration, contact time, and temperature were analyzed. The maximum DMP adsorption capacity of the mag-poly (EGDMA-VP) beads was determined as 96.2 mg/g at pH 3.0, 25 °C. All the isotherm data can be fitted with both the Langmuir and the Dubinin-Radushkevich isotherm models. The pseudo-first-order, pseudo-second-order, Ritch-second-order, and intraparticle diffusion models were used to describe the adsorption kinetics. The thermodynamic parameters obtained indicated the exothermic nature of the adsorption. The DMP adsorption capacity did not change after 10 batch successive reactions, demonstrating the usefulness of the magnetic beads in applications.

Diethyl phthalate removal from aqueous phase using poly(EGDMA-MATrp) beads: kinetic, isothermal and thermodynamic studies

In this study, poly(ethylene glycol dimethacrylate-N-methacryloyl-l-tryptophan methyl ester) [poly(EGDMA-MATrp)] beads (average diameter = 106–300 µm), which were synthesized by co-polymerizing of N-methacryloyl-l-tryptophan methyl ester (MATrp) with ethylene glycol dimethacrylate (EGDMA), were used for diethyl phthalate (DEP) adsorption. The various factors affecting the adsorption of DEP from aqueous solutions such as pH, initial concentration, contact time and temperature were analysed. Adsorption behaviour of DEP on the poly(EGDMA-MATrp) beads was investigated by varying pH values of solution, contact time, initial concentration and temperature. An optimum adsorption capacity of 590.7 mg/g for DEP was obtained at 25 °C. The present adsorption process obeyed a pseudo-second-order kinetic model. All the isotherm data can be fitted with the Langmuir, Freundlich and Dubinin–Radushkevich isotherm models. Thermodynamic parameters ΔH = 7.745 kJ/mol, ΔS = 81.92 J/K/mol and ΔG = −16.69 kJ/mol to −18.31 kJ/mol with the rise in temperature from 25 °C to 45 °C indicated that the adsorption process was endothermic and spontaneous.

Dummy molecularly imprinted microbeads as solid-phase extraction material for selective determination of phthalate esters in water

The aim of this study was to investigate the usability of newly synthesized dummy molecularly imprinted microbeads (DMIMs) as a solid phase extraction (SPE) material to determine six phthalate esters (PEs) in water by GC-MS analysis. Diethyl phthalate (DEP) was used as a dummy template to prepare poly(ethylene glycol dimethacrylate N-methacryloyl-l-tryptophan methyl ester) [PEMATrp)] DMIMs by using suspension polymerization. The PEMATrp DMIMs were characterized by using Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). Firstly, the adsorption capacities of the DMIMs prepared in different template molecule (DEP) to functional monomer (MATrp) ratios were investigated by using DEP solutions in the concentration range of 1-500mg/L at pH 3.0. Styrene and vanillic acid were used to evaluate the selectivity of the prepared DMIMs towards the template molecule (DEP). Then, the best analytical conditions were investigated for the simultaneous determination of dimethyl phthalate (DMP), diethyl phthalate (DEP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP) and di-n-octyl phthalate (DnOP) in aqueous media by using the PEMATrp DMIMs as SPE material. Validation experiments showed that the PEMATrp DMIMs-SPE method had good linearity at 12.5-250.0μg/L (0.988-0.999), good precision (1.2-5.9%), and limits of detection in a range of 0.31-0.41μg/L.

Application of affinity microspheres for effective SPE cleanup before the determination of sulfamerazine by HPLC

This paper describes the application of poly (ethylene glycol dimethacrylate-N-methacryloyl-L-tryptophane methyl ester) [p(EGDMA-MATrp)] microspheres as an affinity sorbent for the SPE (solid phase extraction) cleanup of sulfamerazine (SMR) from food samples of animal origin before high performance liquid chromatography (HPLC) analysis. The microspheres were prepared by suspension polymerization of ethylene glycol dimethacrylate (EGDMA) and N-methacryloyl-L-tryptophane methyl ester (MATrp) as a crosslinker and a monomer, respectively. Various parameters affecting the SPE cleanup efficiency of the p(EGDMA-MATrp) microspheres (contact time, pH, initial SMR concentration, ionic strength etc.) were optimized. Under the optimized conditions, maximum adsorption capacity was found to be 8.55 ± 0.44 mg/g sorbent at pH 5.0. 90% of the adsorbed SMR was desorbed by using ACN:MeOH (5:5) mixture as a desorption agent. Applicability of the microspheres for the SPE cleanup of SMR residues in the food samples such as egg and milk with HPLC was also determined. It was demonstrated that the prepared p(EGDMA-MATrp) microspheres could be repeatedly applied for SPE cleanup of sulfamerazine before chromatographic analysis. Also, the recoveries of SMR in milk and egg samples were reasonably satisfactory and in the range of 71 to 90%.

Adsorption of cinnabarinic acid from culture fluid with magnetic microbeads.

In this study, antimicrobial pigment cinnabarinic acid (CA) was produced from Pycnoporus cinnabarinus in laboratory-scale batch cultures. Magnetic poly(ethylene glycol dimethacrylate-N-methacryloyl-l-tryptophan methyl ester) [m-poly(EGDMA-MATrp)] beads (average diameter = 53-103 µm) were synthesized by copolymerizing of N-methacryloyl-l-tryptophan methyl ester (MATrp) with ethylene glycol dimethacrylate (EGDMA) in the presence of magnetite (Fe3O4) and used for the adsorption of CA. The m-poly(EGDMA-MATrp) beads were characterized by N2 adsorption/desorption isotherms (Brunauer Emmet Teller), X-ray photoelecron spectroscopy, scanning electron microscopy, infrared spectroscopy, thermal gravimetric analysis, electron spin resonance and swelling studies. The efficiency of m-poly(EGDMA-MATrp) beads for separation of CA from culture fluid was evaluated. The effects of pH, initial concentration, contact time and temperature on adsorption were analyzed. The maximum CA adsorption capacity of the m-poly(EGDMA-MATrp) beads was 272.9 mg g(-1) at pH 7.0, 25 °C. All the isotherm data can be fitted with the Langmuir, Freundlich and Dubinin-Radushkevich isotherm models. The adsorption process obeyed pseudo-second-order kinetic model. Thermodynamic parameters ΔH = 5.056 kJ mol(-1), ΔS = 52.44 J K(-1)  mol(-1) and ΔG = -9.424 kJ mol-(1) to -11.27 kJ mol-(1) with the rise in temperature from 4 to 40 °C indicated that the adsorption process was endothermic and spontaneous.