Daiichiro Yokoyama

Effect of loading conditions on the fracture toughness of zirconia

PURPOSE A Vickers hardness indenter was pressed into yttria-stabilized zirconia (Y-TZP) by the indentation fracture method (IF method). METHODS The effect on the calculated Vickers hardness, fracture toughness values, and indentation fracture load (9.8, 49, 98, 196, and 294 N) was examined to deduce the optimum conditions of the IF method. Calculated Vickers hardness and fracture toughness values were analyzed with one-way analysis of variance and then multiple comparisons (Scheffe). The appearance of on indentation and cracks was also evaluated using a scanning electron microscopy (SEM). RESULTS Indentation of Y-TZP was generated by 9.8 and 49 N of indentation fracture load, however cracks could not be confirmed with the microscope attached to the Vickers hardness tester. Both indentation and cracks were observed at 98, 196 and 294 N of indentation fracture load obtained values of 7.1 and 6.8 MPam(1/2). Cracks noted at the 98 N were not clear, whereas the 196 and 294 N showed especially clear cracks. Due to the hardness of zirconia and the light loads, fracture toughness values for 9.8, 49, and 98 N could not be calculated. There was no significant difference between 196 and 294 N, when calculated fracture toughness values were analyzed with multiple comparisons. SEM revealed clear indentation and cracks, that extended linearly, but no chips or fractures were observed. Surface changes were observed at 196 and 294 N that are presumed to be accompanied by phase transition around the cracks. CONCLUSIONS Optimum experimental conditions of the indentation fracture load in the IF method were determined as 196 and 294 N.

The effect of surface treatment on bond strength of layering porcelain and hybrid composite bonded to zirconium dioxide ceramics

PURPOSE The purpose of this study was to investigate the differences between Rocatec (as surface treatment) and #600 polishing (as control) on shear bond strength of layering porcelain and hybrid composite to zirconium dioxide ceramics. METHODS Manufactured zirconia blocks used in this study were yttrium partially stabilized zirconia (YTZ(®)), and veneering materials were NobelRondo Zirconia Dentin A2 High Value (NZR) and Estenia C&B (ES). Total 48 zirconia blocks were fabricated (10 mm × 10 mm × 20 mm). The blocks of 24 each were treated by Rocatec and #600 paper, respectively. Surface treated zirconia blocks were divided into two groups, according to veneering materials of NZR and ES. NZR was fired and ES was polymerized to zirconia. The fabricated specimen was fixed to mounting jig and applied shear force using the universal testing machine at a crosshead speed of 0.5 mm/min. All results were statistically analyzed by two-way ANOVA and Tukeys test. EPMA analysis and SPM analysis of specimen interface were carried out. RESULTS Mean shear bond strength of each condition was: NZR/#600; 23.3 (S.D. ±7.0) MPa, NZR/Rocatec; 26.9 (S.D. ±7.0) MPa, ES/#600; 10.7 (S.D.±2.4) MPa, ES/Rocatec; 12.5 (S.D.±0.8) MPa. CONCLUSIONS From the results of this study, shear bond strength of layering porcelain to zirconia was higher than that of restorative hybrid resin. However the more study will be needed, the appropriate choice of materials became the gides to the expansion of the applied cases of metal-free prothesis.

Finite Element Analysis for Dental Prosthetic Design

Akikazu Shinya, DDS, PhD Department of Crown and Bridge, School of Life Dentistry at Tokyo, The Nippon Dental University, Japan, Honorary Assistant Professor, Dental Materials Science Unit, Faculty of Dentistry, The University of Hong Kon and Research scientist, Department of Biomaterials Science, Institute of Dentistry and BioCity Turku Biomaterials Research Program, University of Turku Daiichiro Yokoyama, DDS, PhD Department of Crown and Bridge, School of Life Dentistry at Tokyo, The Nippon Dental University, 1-9-20 Fujimi, Chiyoda-ku, Tokyo 102-8158, Japan.

Fiber-reinforced Composite Resin Prosthesis to Restore Missing Posterior Teeth: A Case Report

A fiber-reinforced composite inlay-onlay FPD was used for a single posterior tooth replacement in a patient refusing implant for psychological reasons. The FRC-FPD was made of pre-impregnated E-glass fibers (everStick, StickTeck, Turku, Finland) embedded in a resin matrix (Stick Resin, StickTeck, Turku, Finland). The unidirectional glass fibers were used to make a framework structure with high volume design placed in the pontic (edentulous) region. To reproduce the morphology of natural teeth, the framework structure was then veneered with Gradia (GC, Tokyo, Japan).