Eklavya Singh

Defect-induced plating of lithium metal within porous graphene networks

Lithium metal is known to possess a very high theoretical capacity of 3,842 mAh g(-1) in lithium batteries. However, the use of metallic lithium leads to extensive dendritic growth that poses serious safety hazards. Hence, lithium metal has long been replaced by layered lithium metal oxide and phospho-olivine cathodes that offer safer performance over extended cycling, although significantly compromising on the achievable capacities. Here we report the defect-induced plating of metallic lithium within the interior of a porous graphene network. The network acts as a caged entrapment for lithium metal that prevents dendritic growth, facilitating extended cycling of the electrode. The plating of lithium metal within the interior of the porous graphene structure results in very high specific capacities in excess of 850 mAh g(-1). Extended testing for over 1,000 charge/discharge cycles indicates excellent reversibility and coulombic efficiencies above 99%.

Superhydrophobic Graphene Foams

The static and dynamic wetting properties of a 3D graphene foam network are reported. The foam is synthesized using template-directed chemical vapor deposition and contains pores several hundred micrometers in dimension while the walls of the foam comprise few-layer graphene sheets that are coated with Teflon. Water contact angle measurements reveal that the foam is superhydrophobic with an advancing contact angle of ∼163 degrees while the receding contact angle is ∼143 degrees. The extremely water repellent nature of the foam is also confirmed when impacting water droplets are able to completely rebound from the surface. Such superhydrophobic graphene foams show potential in a variety of applications ranging from anti-sticking and self-cleaning to anti-corrosion and low-friction coatings.

Graphene Drape Minimizes the Pinning and Hysteresis of Water Drops on Nanotextured Rough Surfaces

Previous studies of the interaction of water with graphene-coated surfaces have been limited to flat (smooth) surfaces. Here we created a rough surface by nanopatterning and then draped the surface with a single-layer graphene sheet. We found that the ultrasheer graphene drape prevents the penetration of water into the textured surface thereby drastically reducing the contact angle hysteresis (which is a measure of frictional energy dissipation) and preventing the liquid contact line from getting pinned to the substrate. This has important technological implications since the main obstacle to the motion of liquid drops on rough surfaces is contact angle hysteresis and contact line pinning. Graphene drapes could therefore enable enhanced droplet mobility which is required in a wide range of applications in micro and nanofluidics. Compared to polymer coatings that could fill the cavities between the nano/micropores or significantly alter the roughness profile of the substrate, graphene provides the thinnest (i.e., most sheer) and most conformal drape that is imaginable. Despite its extreme thinness, the graphene drape is mechanically robust, chemically stable, and offers high flexibility and resilience which can enable it to reliably drape arbitrarily complex surface topologies. Graphene drapes may therefore provide a hitherto unavailable ability to tailor the dynamic wettability of surfaces for a variety of applications.

Graphene Oxide Colloidal Suspensions as Cutting Fluids for Micromachining—Part I: Fabrication and Performance Evaluation

This paper is aimed at investigating the effects of graphene oxide platelet (GOP) geometry (i.e., lateral size and thickness) and oxygen functionalization on the cooling and lubrication performance of GOP colloidal suspensions. The techniques of thermal reduction and ultrasonic exfoliation were used to manufacture three different types of GOPs. For each of these three types of GOPs, colloidal solutions with GOP concentrations varying between 0.1–1 wt% were evaluated for their dynamic viscosity, thermal conductivity and micromachining performance. The ultrasonically-exfoliated GOPs (with 2–3 graphene layers and lowest in-solution characteristic lateral length of 120 nm) appear to be the most favorable for micromachining applications. Even at the lowest concentration of 0.1 wt%, they are capable of providing a 51% reduction in the cutting temperature and a 25% reduction in the surface roughness value over that of the baseline semi-synthetic cutting fluid. For the thermally-reduced GOPs (with 4–8 graphene layers and in-solution characteristic lateral length of 562–2780 nm), a concentration of 0.2 wt% appears to be optimal. The findings suggest that the differences seen between the colloidal suspensions in terms of their droplet spreading, evaporation and the subsequent GOP film-formation characteristics may be better indicators of their machining performance, as opposed to their bulk fluid properties.Copyright

Graphene Oxide Colloidal Suspensions as Cutting Fluids for Micromachining: Part 1 — Fabrication and Performance Evaluation

This paper is aimed at investigating the effects of graphene oxide platelet (GOP) geometry (i.e., lateral size and thickness) and oxygen functionalization on the cooling and lubrication performance of GOP colloidal suspensions. The techniques of thermal reduction and ultrasonic exfoliation were used to manufacture three different types of GOPs. For each of these three types of GOPs, colloidal solutions with GOP concentrations varying between 0.1–1 wt% were evaluated for their dynamic viscosity, thermal conductivity and micromachining performance. The ultrasonically-exfoliated GOPs (with 2–3 graphene layers and lowest in-solution characteristic lateral length of 120 nm) appear to be the most favorable for micromachining applications. Even at the lowest concentration of 0.1 wt%, they are capable of providing a 51% reduction in the cutting temperature and a 25% reduction in the surface roughness value over that of the baseline semi-synthetic cutting fluid. For the thermally-reduced GOPs (with 4–8 graphene layers and in-solution characteristic lateral length of 562–2780 nm), a concentration of 0.2 wt% appears to be optimal. The findings suggest that the differences seen between the colloidal suspensions in terms of their droplet spreading, evaporation and the subsequent GOP film-formation characteristics may be better indicators of their machining performance, as opposed to their bulk fluid properties.Copyright