Elzbieta Pamula

Enzymatic mineralization of gellan gum hydrogel for bone tissue-engineering applications and its enhancement by polydopamine

Interest is growing in the use of hydrogels as bone tissue‐engineering (TE) scaffolds due to advantages such as injectability and ease of incorporation of active substances such as enzymes. Hydrogels consisting of gellan gum (GG), an inexpensive calcium‐crosslinkable polysaccharide, have been applied in cartilage TE. To improve GG suitability as a material for bone TE, alkaline phosphatase (ALP), an enzyme involved in mineralization of bone by cleaving phosphate from organic phosphate, was incorporated into GG hydrogels to induce mineralization with calcium phosphate (CaP). Incorporated ALP induced formation of apatite‐like material on the submicron scale within GG gels, as shown by FTIR, SEM, EDS, XRD, ICP‐OES, TGA and von Kossa staining. Increasing ALP concentration increased amounts of CaP as well as stiffness. Mineralized GG was able to withstand sterilization by autoclaving, although stiffness decreased. In addition, mineralizability and stiffness of GG was enhanced by the incorporation of polydopamine (PDA). Furthermore, mineralization of GG led to enhanced attachment and vitality of cells in vitro while cytocompatibility of the mineralized gels was comparable to one of the most commonly used bone substitute materials. The results proved that ALP‐mediated enzymatic mineralization of GG could be enhanced by functionalization with PDA. Copyright

Generation of composites for bone tissue-engineering applications consisting of gellan gum hydrogels mineralized with calcium and magnesium phosphate phases by enzymatic means.

Mineralization of hydrogels, desirable for bone regeneration applications, may be achieved enzymatically by incorporation of alkaline phosphatase (ALP). ALP‐loaded gellan gum (GG) hydrogels were mineralized by incubation in mineralization media containing calcium and/or magnesium glycerophosphate (CaGP, MgGP). Mineralization media with CaGP:MgGP concentrations 0.1:0, 0.075:0.025, 0.05:0.05, 0.025:0.075 and 0:0.1 (all values mol/dm3, denoted A, B, C, D and E, respectively) were compared. Mineral formation was confirmed by IR and Raman, SEM, ICP‐OES, XRD, TEM, SAED, TGA and increases in the the mass fraction of the hydrogel not consisting of water. Ca was incorporated into mineral to a greater extent than Mg in samples mineralized in media A–D. Mg content and amorphicity of mineral formed increased in the order A < B < C < D. Mineral formed in media A and B was calcium‐deficient hydroxyapatite (CDHA). Mineral formed in medium C was a combination of CDHA and an amorphous phase. Mineral formed in medium D was an amorphous phase. Mineral formed in medium E was a combination of crystalline and amorphous MgP. Youngs moduli and storage moduli decreased in dependence of mineralization medium in the order A > B > C > D, but were significantly higher for samples mineralized in medium E. The attachment and vitality of osteoblastic MC3T3‐E1 cells were higher on samples mineralized in media B–E (containing Mg) than in those mineralized in medium A (not containing Mg). All samples underwent degradation and supported the adhesion of RAW 264.7 monocytic cells, and samples mineralized in media A and B supported osteoclast‐like cell formation. Copyright

Electrochemical and biological characterization of coatings formed on Ti–15Mo alloy by plasma electrolytic oxidation

β-Type titanium alloys are considered the future materials for bone implants. To improve the bioactivity of Ti-15Mo, the surface was modified using the plasma electrolytic oxidation (PEO) process. Tricalcium phosphate (TCP, Ca3PO4), wollastonite (CaSiO3) and silica (SiO2) were selected as additives in the anodizing bath to enhance the bioactivity of the coatings formed during the PEO process. Electrochemical analysis of the samples was performed in Ringers solution at 37°C. The open-circuit potential (EOCP) as a function of time, corrosion potential (ECORR), corrosion current density (jCORR) and polarization resistance (Rp) of the samples were determined. Surface modification improved the corrosion resistance of Ti-15Mo in Ringers solution. In vitro studies with MG-63 osteoblast-like cells were performed for 1, 3 and 7 days. After 24h, the cells were well adhered on the entire surfaces, and their number increased with increasing culture time. The coatings formed in basic solution with wollastonite exhibited better biological performance compared with the as-ground sample.

Incorporation of sol-gel bioactive glass into PLGA improves mechanical properties and bioactivity of composite scaffolds and results in their osteoinductive properties.

In this study, 3D porous bioactive composite scaffolds were produced and evaluated for their physico-chemical and biological properties. Polymer poly-L-lactide-co-glycolide (PLGA) matrix scaffolds were modified with sol-gel-derived bioactive glasses (SBGs) of CaO-SiO2-P2O5 systems. We hypothesized that SBG incorporation into PLGA matrix would improve the chemical and biological activity of composite materials as well as their mechanical properties. We applied two bioactive glasses, designated as S2 or A2, differing in the content of SiO2 and CaO (i.e. 80 mol% SiO2, 16 mol% CaO for S2 and 40 mol% SiO2, 52 mol% CaO for A2). The composites were characterized for their porosity, bioactivity, microstructure and mechanical properties. The osteoinductive properties of these composites were evaluated in human bone marrow stromal cell (hBMSC) cultures grown in either standard growth medium or treated with recombinant human bone morphogenetic protein-2 (rhBMP-2) or dexamethasone (Dex). After incubation in simulated body fluid, calcium phosphate precipitates formed inside the pores of both A2-PLGA and S2-PLGA scaffolds. The compressive strength of the latter was increased slightly compared to PLGA. Both composites promoted superior hBMSC attachment to the material surface and stimulated the expression of several osteogenic markers in hBMSC compared to cells grown on unmodified PLGA. There were also marked differences in the response of hBMSC to composite scaffolds, depending on chemical compositions of the scaffolds and culture treatments. Compared to silica-rich S2-PLGA, hBMSC grown on calcium-rich A2-PLGA were overall less responsive to rhBMP-2 or Dex and the osteoinductive properties of these A2-PLGA scaffolds seemed partially dependent on their ability to induce BMP signaling in untreated hBMSC. Thus, beyond the ability of currently studied composites to enhance hBMSC osteogenesis, it may become possible to modulate the osteogenic response of hBMSC, depending on the chemistry of SBGs incorporated into polymer matrix.

Enzymatically induced mineralization of platelet-rich fibrin †

Membranes of the autologous blood-derived biomaterial platelet-rich fibrin (PRF) were functionalized by incorporation of alkaline phosphatase (ALP), an enzyme involved in mineralization of bone, and subsequently incubated in calcium glycerophosphate (CaGP) solution to induce PRFs mineralization with calcium phosphate (CaP) to improve PRFs suitability as a material for bone replacement. Incorporated ALP retained its bioactivity and induced formation of CaP material within PRF membranes, as confirmed by SEM, EDS, FTIR, and von Kossa staining. The mass percentage attributable to CaP was quantified by lyophilization and measurement of the remaining mass fraction as well as by TGA. Cytocompatibility tests (LDH, MTT, and WST) with SAOS-2 cells showed that mineralized PRF did not release substances detrimental to cell vitality. Live/dead staining and SEM showed that mineralized PRF was colonized by cells. The results show that hydrogel biomaterials such as PRF can be mineralized through functionalization with ALP.

Cytocompatibility of aliphatic polyesters--in vitro study on fibroblasts and macrophages.

A resorbable copolymer of glycolide and L-lactide (PGLA), a terpolymer of glycolide, L-lactide, and epsilon-caprolactone (PGLCL), and a copolymer of glycolide and epsilon-caprolactone (PGCL) were synthesized by ring opening polymerization using zirconium acetylacetonate (Zr(acac)(4)) as an initiator. The structure and physicochemical surface properties of the materials were studied by NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry, X-ray photoelectron spectroscopy, atomic force microscopy, and contact angle measurements. On the basis of contact angle measurements and the Owens-Wendt approach, the surface free energy was calculated. The effect of polymeric films produced by solvent casting on morphology and activity of L929 fibroblasts, and two types of macrophages (macrophages from peritoneal exudates and RAW 264.7 monocytes/macrophages), was analyzed. It was found that viability, adhesion, and morphology of fibroblasts on PGLA were very similar to control glass. On PGLCL more adhering cells were round, while on PGCL only single, poorly spread cells were seen, and their viability was significantly reduced. This may suggest that the interaction of fibroblasts with PGCL was due to its hydrophobicity and a very low polarity. Adhesion and viability of RAW 264.7 cells was significantly enhanced on PGLA but reduced on both PGLCL and PGCL. The increased synthesis/release of chemoattractants and metalloproteinases-2 and -9 was observed in the macrophages from peritoneal exudates cultured on PGLA and PGLCL. The viability of cells decreased in the following order: PGLA > PGLCL > PGCL. It is worth noting that glass transition temperature and susceptibility to mechanical deformation of the polymeric materials also decreased in the same order. It may imply that those physical parameters should be also considered as potential factors affecting cell behavior.

Injectable self-gelling composites for bone tissue engineering based on gellan gum hydrogel enriched with different bioglasses

Hydrogels of biocompatible calcium-crosslinkable polysaccharide gellan gum (GG) were enriched with bioglass particles to enhance (i) mineralization with calcium phosphate (CaP); (ii) antibacterial properties and (iii) growth of bone-forming cells for future bone regeneration applications. Three bioglasses were compared, namely one calcium-rich and one calcium-poor preparation both produced by a sol-gel technique (hereafter referred to as A2 and S2, respectively) and one preparation of composition close to that of the commonly used 45S5 type (hereafter referred to as NBG). Incubation in SBF for 7 d, 14 d and 21 d caused apatite formation in bioglass-containing but not in bioglass-free samples, as confirmed by FTIR, XRD, SEM, ICP-OES, and measurements of dry mass, i.e. mass attributable to polymer and mineral and not water. Mechanical testing revealed an increase in compressive modulus in samples containing S2 and NBG but not A2. Antibacterial testing using biofilm-forming meticillin-resistant staphylococcus aureus (MRSA) showed markedly higher antibacterial activity of samples containing A2 and S2 than samples containing NBG and bioglass-free samples. Cell biological characterization using rat mesenchymal stem cells (rMSCs) revealed a stimulatory effect of NBG on rMSC differentiation. The addition of bioglass thus promotes GG mineralizability and, depending on bioglass type, antibacterial properties and rMSC differentiation.

Linseed oil based nanocapsules as delivery system for hydrophobic quantum dots.

In the present work, the CdSe/ZnS hydrophobic quantum dots were embedded within the polyelectrolyte nanocapsules. The core of the capsules, which consists of a mixture of the linseed oil with chloroform, was prepared using the spontaneous emulsification technique. The obtained emulsions were stabilized with lecithin and encapsulated using the layer-by-layer (LbL) adsorption of polyelectrolytes. The pair of biocompatible polyelectrolytes was used: the cationic poly-l-lysine hydrobromide (PLL) together with the anionic poly-d-glutamic acid sodium salt. The saturation LbL method, which is based on the stepwise formation of consecutive layers on the initial emulsion without the intermediate rinsing step, was applied to form the capsule shells. Their growth was evidenced by the capsule size and electrophoretic mobility measurements. The emulsion and the capsules were deposited on a mica surface and the deposit topology was examined by the means of atomic force microscopy (AFM). The presence of quantum dots within the oil cores was confirmed by recording the fluorescent spectra of the samples containing CdSe/ZnS. In order to evaluate cytotoxicity of the capsules, their influence on the viability of mouse embryonic fibroblasts was examined using the MTT test, followed by optical-microscope observation of morphology of the cells after hematoxylin-eosin staining.

Injectable nanoparticle-loaded hydrogel system for local delivery of sodium alendronate.

Systemic administration of bisphosphonates, e.g. sodium alendronate (Aln) is characterized by extremely low bioavailability and high toxicity. To omit aforementioned drawbacks an injectable system for the intra-bone delivery of Aln based on Aln-loaded nanoparticles (NPs-Aln) suspended in a hydrogel matrix (gellan gum, GG) was developed. Aln was encapsulated in poly(lactide-co-glycolide) (PLGA 85:15) by solid-oil-water emulsification. Drug release tests showed that within 25 days all the encapsulated drug was released from NPs-Aln and the release rate was highest at the beginning and decreased with time. In contrast, by suspending NPs-Aln in a GG matrix, the release rate was significantly lower and more constant in time. The GG-NPs-Aln system was engineered to be easily injectable and was able to reassemble its structure after extrusion as shown by rheological measurements. Invitro studies showed that the GG-NPs-Aln was cytocompatible with MG-63 osteoblast-like cells and it inhibited RANKL-mediated osteoclastic differentiation of RAW 264.7 cells. The injectability, the sustained local delivery of small doses of Aln and the biological activity render the GG-NPs-Aln system promising for the local treatment of osteoporosis and other bone tissue disorders.

Effects of Aliphatic Polyesters on Activation of the Immune System: Studies on Macrophages

There is a constant search for biodegradable polymers with biocompatible characteristics. However, the reported materials are rarely tested for their immunostimulatory properties, which is an important issue as immune cells activated by the polymers might cause their rejection and lead to further injury to the host tissues. Therefore, the aim of the present study was to determine if biodegradable polymers are able to activate RAW 264.7 macrophages. Aliphatic polyesters, poly(L-lactide) (PLLA), poly(L-lactide-co-trimethylene carbonate) (PLTMC), poly(glycolide-co-L-lactide) (PGLA), poly(glycolide-co-L-lactide-co-ε-caprolactone) (PGLCap) and poly(glycolide-co-ε-caprolactone) (PGCap), processed into foils by slip-casting, were characterized in terms of their structure (1H-NMR, GPC, DSC) and surface properties (chemical composition, water contact angle, surface free energy, topography and roughness). RAW 264.7 cells were cultured on the materials for 3 or 5 days and their adherence, numbers of apoptotic/necrotic cells, as well as production of several cytokines/chemokines and other inflammation-related molecules (matrix metalloproteinases, nitric oxide) was evaluated. The study demonstrated that PLLA and PGLA did not influence macrophage activation and survival. In contrast, PLTMC, PGLCap and PGCap significantly decreased macrophage adherence, increased ratio of apoptosis and up-regulated synthesis/release of numerous inflammatory mediators. Thus, the latter materials might initiate an undesired inflammatory reaction. The above effects of the polymers were attributed to their high hydrophobicity and low polarity due to the presence of ε-caproyl blocks (PGLCap and PGCap), and/or high flexibility and susceptibility to mechanical deformation due to low glasstransition temperature (PLTMC, PGLCap and PGCap). In conclusion, while PLLA and PGLA do not affect macrophage functioning, the other materials (PLTMC, PGLCap, PGCap) up-regulate macrophage activity.