Etienne Renotte

Far Ultraviolet Imaging from the Image Spacecraft: 1. System Design

Direct imaging of the magnetosphere by the IMAGE spacecraft will be supplemented by observation of the global aurora, the footprint of magnetospheric regions. To assure the simultaneity of these observations and the measurement of the magnetospheric background neutral gas density, the IMAGE satellite instrument complement includes three Far Ultraviolet (FUV) instruments. In the wavelength region 120-190 nm, a downward-viewing auroral imager is only minimally contaminated by sunlight, scattered from clouds and ground, and radiance of the aurora observed in a nadir viewing geometry can be observed in the presence of the high-latitude dayglow. The Wideband Imaging Camera (WIC) will provide broad band ultraviolet images of the aurora for maximum spatial and temporal resolution by imaging the LBH N2 bands of the aurora. The Spectrographic Imager (SI), a monochromatic imager, will image different types of aurora, filtered by wavelength. By measuring the Doppler-shifted Ly-α, the proton-induced component of the aurora will be imaged separately. Finally, the GEO instrument will observe the distribution of the geocoronal emission, which is a measure of the neutral background density source for charge exchange in the magnetosphere. The FUV instrument complement looks radially outward from the rotating IMAGE satellite and, therefore, it spends only a short time observing the aurora and the Earth during each spin. Detailed descriptions of the WIC, SI, GEO, and their individual performance validations are discussed in companion papers. This paper summarizes the system requirements and system design approach taken to satisfy the science requirements. One primary requirement is to maximize photon collection efficiency and use efficiently the short time available for exposures. The FUV auroral imagers WIC and SI both have wide fields of view and take data continuously as the auroral region proceeds through the field of view. To minimize data volume, multiple images are taken and electronically co-added by suitably shifting each image to compensate for the spacecraft rotation. In order to minimize resolution loss, the images have to be distortion-corrected in real time for both WIC and SI prior to co-adding. The distortion correction is accomplished using high speed look up tables that are pre-generated by least square fitting to polynomial functions by the on-orbit processor. The instruments were calibrated individually while on stationery platforms, mostly in vacuum chambers as described in the companion papers. Extensive ground-based testing was performed with visible and near UV simulators mounted on a rotating platform to estimate their on-orbit performance. The predicted instrument system performance is summarized and some of the preliminary data formats are shown.

OMC: An Optical Monitoring Camera for INTEGRAL Instrument description and performance

The Optical Monitoring Camera (OMC) will observe the optical emission from the prime targets of the gamma- ray instruments onboard the ESA mission INTEGRAL, with the support of the JEM-X monitor in the X-ray domain. This capability will provide invaluable diagnostic information on the nature and the physics of the sources over a broad wavelength range. Its main scientific objectives are: (1) to monitor the optical emission from the sources observed by the gamma- and X-ray instruments, measuring the time and intensity structure of the optical emission for comparison with variability at high energies, and (2) to provide the brightness and position of the optical counterpart of any gamma- or X-ray transient taking place within its field of view. The OMC is based on a refractive optics with an aperture of 50 mm focused onto a large format CCD (1024 2048 pixels) working in frame transfer mode (1024 1024 pixels imaging area). With a field of view of 5 5 it will be able to monitor sources down to magnitude V = 18. Typical observations will perform a sequence of dierent integration times, allowing for photometric uncertainties below 0.1 mag for objects with V 16.

The Mid-Infrared Instrument for the James Webb Space Telescope, II: Design and Build

The Mid-InfraRed Instrument (MIRI) on the James Webb Space Telescope (JWST) provides measurements over the wavelength range 5 to 28.5 μm. MIRI has, within a single ‘package’, four key scientific functions: photometric imaging, coronagraphy, single-source low-spectral resolving power (R ∼ 100) spectroscopy, and medium-resolving power (R ∼ 1500 to 3500) integral field spectroscopy. An associated cooler system maintains MIRI at its operating temperature of <6.7 K. This paper describes the driving principles behind the design of MIRI, the primary design parameters, and their realisation in terms of the ‘as-built’ instrument. It also describes the test programme that led to delivery of the tested and calibrated Flight Model to NASA in 2012, and the confirmation after delivery of the key interface requirements.

First light of SWAP on-board PROBA2

The SWAP telescope (Sun Watcher using Active Pixel System detector and Image Processing) is an instrument launched on 2nd November 2009 on-board the ESA PROBA2 technological mission. SWAP is a space weather sentinel from a low Earth orbit, providing images at 174 nm of the solar corona. The instrument concept has been adapted to the PROBA2 mini-satellite requirements (compactness, low power electronics and a-thermal opto-mechanical system). It also takes advantage of the platform pointing agility, on-board processor, Packetwire interface and autonomous operations. The key component of SWAP is a radiation resistant CMOS-APS detector combined with onboard compression and data prioritization. SWAP has been developed and qualified at the Centre Spatial de Liège (CSL) and calibrated at the PTBBessy facility. After launch, SWAP has provided its first images on 14th November 2009 and started its nominal, scientific phase in February 2010, after 3 months of platform and payload commissioning. This paper summarizes the latest SWAP developments and qualifications, and presents the first light results.

The EUI instrument on board the Solar Orbiter mission: from breadboard and prototypes to instrument model validation

The Solar Orbiter mission will explore the connection between the Sun and its heliosphere, taking advantage of an orbit approaching the Sun at 0.28 AU. As part of this mission, the Extreme Ultraviolet Imager (EUI) will provide full-sun and high-resolution image sequences of the solar atmosphere at selected spectral emission lines in the extreme and vacuum ultraviolet. To achieve the required scientific performances under the challenging constraints of the Solar Orbiter mission it was required to further develop existing technologies. As part of this development, and of its maturation of technology readiness, a set of breadboard and prototypes of critical subsystems have thus been realized to improve the overall instrument design. The EUI instrument architecture, its major components and sub-systems are described with their driving constraints and the expected performances based on the breadboard and prototype results. The instrument verification and qualification plan will also be discussed. We present the thermal and mechanical model validation, the instrument test campaign with the structural-thermal model (STM), followed by the other instrument models in advance of the flight instrument manufacturing and AIT campaign.

The technical challenges of the Solar-Orbiter EUI instrument

The Extreme Ultraviolet Imager (EUI) onboard Solar Orbiter consists of a suite of two high-resolution imagers (HRI) and one dual-band full Sun imager (FSI) that will provide EUV and Lyman-α images of the solar atmospheric layers above the photosphere. The EUI instrument is based on a set of challenging new technologies allowing to reach the scientific objectives and to cope with the hard space environment of the Solar Orbiter mission. The mechanical concept of the EUI instrument is based on a common structure supporting the HRI and FSI channels, and a separated electronic box. A heat rejection baffle system is used to reduce the Sun heat load and provide a first protection level against the solar disk straylight. The spectral bands are selected by thin filters and multilayer mirror coatings. The detectors are 10μm pitch back illuminated CMOS Active Pixel Sensors (APS), best suited for the EUI science requirements and radiation hardness. This paper presents the EUI instrument concept and its major sub-systems. The current developments of the instrument technologies are also summarized.

Design status of ASPIICS, an externally occulted coronagraph for PROBA-3

The “sonic region” of the Sun corona remains extremely difficult to observe with spatial resolution and sensitivity sufficient to understand the fine scale phenomena that govern the quiescent solar corona, as well as phenomena that lead to coronal mass ejections (CMEs), which influence space weather. Improvement on this front requires eclipse-like conditions over long observation times. The space-borne coronagraphs flown so far provided a continuous coverage of the external parts of the corona but their over-occulting system did not permit to analyse the part of the white-light corona where the main coronal mass is concentrated. The proposed PROBA-3 Coronagraph System, also known as ASPIICS (Association of Spacecraft for Polarimetric and Imaging Investigation of the Corona of the Sun), with its novel design, will be the first space coronagraph to cover the range of radial distances between ~1.08 and 3 solar radii where the magnetic field plays a crucial role in the coronal dynamics, thus providing continuous observational conditions very close to those during a total solar eclipse. PROBA-3 is first a mission devoted to the in-orbit demonstration of precise formation flying techniques and technologies for future European missions, which will fly ASPIICS as primary payload. The instrument is distributed over two satellites flying in formation (approx. 150m apart) to form a giant coronagraph capable of producing a nearly perfect eclipse allowing observing the sun corona closer to the rim than ever before. The coronagraph instrument is developed by a large European consortium including about 20 partners from 7 countries under the auspices of the European Space Agency. This paper is reviewing the recent improvements and design updates of the ASPIICS instrument as it is stepping into the detailed design phase.

The x-ray microcalorimeter spectrometer onboard Athena

One of the instruments on the Advanced Telescope for High-Energy Astrophysics (Athena) which was one of the three missions under study as one of the L-class missions of ESA, is the X-ray Microcalorimeter Spectrometer (XMS). This instrument, which will provide high-spectral resolution images, is based on X-ray micro-calorimeters with Transition Edge Sensor (TES) and absorbers that consist of metal and semi-metal layers and a multiplexed SQUID readout. The array (32 x 32 pixels) provides an energy resolution of < 3 eV. Due to the large collection area of the Athena optics, the XMS instrument must be capable of processing high counting rates, while maintaining the spectral resolution and a low deadtime. In addition, an anti-coincidence detector is required to suppress the particle-induced background. Compared to the requirements for the same instrument on IXO, the performance requirements have been relaxed to fit into the much more restricted boundary conditions of Athena. In this paper we illustrate some of the science achievable with the instrument. We describe the results of design studies for the focal plane assembly and the cooling systems. Also, the system and its required spacecraft resources will be given.

The extreme UV imager of solar orbiter: from detailed design to flight model

The Extreme Ultraviolet Imager (EUI) on-board the Solar Orbiter mission will provide full-sun and high-resolution image sequences of the solar atmosphere at selected spectral emission lines in the extreme and vacuum ultraviolet. After the breadboarding and prototyping activities that focused on key technologies, the EUI project has completed the design phase and has started the final manufacturing of the instrument and its validation. The EUI instrument has successfully passed its Critical Design Review (CDR). The process validated the detailed design of the Optical Bench unit and of its sub-units (entrance baffles, doors, mirrors, camera, and filter wheel mechanisms), and of the Electronic Box unit. In the same timeframe, the Structural and Thermal Model (STM) test campaign of the two units have been achieved, and allowed to correlate the associated mathematical models. The lessons learned from STM and the detailed design served as input to release the manufacturing of the Qualification Model (QM) and of the Flight Model (FM). The QM will serve to qualify the instrument units and sub-units, in advance of the FM acceptance tests and final on-ground calibration.

Design and modelisation of ASPIICS optics

In the framework of development of ASPIICS (Association of Spacecraft for Polarimetric and Imaging Investigation of the Corona of the Sun), the Centre Spatial de Liege is responsible of the optical design of the coronagraph and the optics will be manufactured by TOPTEC. The particularity of this coronagraph is to have an external occulter located 150 m ahead of the first imaging lens. This external occulter is re-imaged on an internal occulter which function is - as in a classical externally occulted Lyot coronagraph - to block the sun light diffracted by the external occulter and to reduce the straylight on the detector. The selection of this configuration is driven by the requirement to observe the corona as close as possible to the solar limb (i.e. 1 RSun) without imaging the limb itself. A requirement of 1.08 RSun is specified at optical design level to grant 1.2 Rsun at instrument level. The coronograph instrument is designed to have a field of view of 1.6° x 1.6° with a resolution of less than 6 arcsec. Its performances are limited by diffraction in a 530 – 590 nm wavelength range. This paper presents the optical design and demonstrates that by design the requirements are fulfilled within the misalignment, manufacturing and thermo-elastic error contributions.