Fernanda Ribeiro Santana

Finite element analysis and bond strength of a glass post to intraradicular dentin: Comparison between microtensile and push-out tests

OBJECTIVE This study tested the hypothesis that the stress distribution and bond strength of glass posts to intraradicular dentin is influenced by the mechanical testing methodology. METHODS Thirty single rooted endodontically treated teeth were prepared for luting of tapered fiber-glass posts (Reforpost, Angelus, Londrina, PR, Brazil) with a conventional adhesive system and resin luting cement (Adper Scotchbond Multi-purpose, Rely X ARC, 3M ESPE, St. Paul, MN, USA). The teeth were randomly divided (n=10 per group) into micro-push-out (Mpo), hourglass- (Mh) and rectangular stick-shaped (Ms) microtensile testing groups before sectioning each root into five 1-mm-thick specimens. During specimen preparation for microTBS testing 46/50 stick and 4/50 hourglass specimens prematurely failed; therefore, the Ms group could not be included in the mechanical testing. The remaining specimens were tested at 0.5 mm/min until bond failure. Stress distribution within each specimen type for the three mechanical test methods was analyzed by finite element analysis (FEA). Qualitative analyses were carried out through Von Mises, XY and Sy criterion. RESULTS Mpo and Mh had a mean microTBS of 11.89+/-6.55 and 14.98+/-12.72 MPa, respectively, which was not significantly different (p=0.1311). The push-out test demonstrated a more homogenous stress distribution by FEA and less variability in mechanical testing. SIGNIFICANCE Therefore, the recommended testing method for determining the bond strength of glass posts to intraradicular dentin is by Mpo.

Influence of airborne-particle abrasion on mechanical properties and bond strength of carbon/epoxy and glass/bis-GMA fiber-reinforced resin posts.

STATEMENT OF PROBLEM Controversy exists concerning the use of fiber-reinforced posts to improve bond strength to resin cement because some precementation treatments can compromise the mechanical properties of the posts. PURPOSE The purpose of this study was to analyze the influence of airborne-particle abrasion on the mechanical properties and microtensile bond strength (MTBS) of carbon/epoxy and glass/bis-GMA fiber-reinforced resin posts. MATERIAL AND METHODS Flexural strength (delta(f)), flexural modulus (E(f)), and stiffness (S) were assessed using a 3-point bending test for glass fiber-reinforced and carbon fiber-reinforced resin posts submitted to airborne-particle abrasion (AB) with 50-microm Al(2)O(3), and for posts without any surface treatment (controls) (n=10). Forty glass fiber (GF) and 40 carbon fiber (CF) posts were submitted to 1 of 4 surface treatments (n=10) prior to MTBS testing: silane (S); silane and adhesive (SA); airborne-particle abrasion with 50-microm Al(2)O(3) and silane (ABS); airborne-particle abrasion, silane, and adhesive (ABSA). Two composite resin restorations (Filtek Z250) with rounded depressions in the lateral face were bilaterally fixed to the post with resin cement (RelyX ARC). Next, the specimen was sectioned with a precision saw running perpendicular to the bonded surface to obtain 10 bonded beam specimens with a cross-sectional area of 1 mm(2). Each beam specimen was tested in a mechanical testing machine (EMIC 2,000 DL), under stress, at a crosshead speed of 0.5 mm/min until failure. Data were analyzed by 2-way ANOVA followed by Tukey HSD test (alpha=.05). Failure patterns of tested specimens were analyzed using scanning electron microscopy (SEM). RESULTS The 3-point bending test demonstrated significant differences among groups only for the post type factor for flexural strength, flexural modulus, and stiffness. The carbon fiber posts exhibited significantly higher mean flexural strength (P=.001), flexural modulus (P=.003), and stiffness (P=.001) values when compared with glass fiber posts, irrespective of surface treatment. An alteration in the superficial structure of the posts could be observed by SEM after airborne-particle abrasion. MTBS testing showed no significant effect for the surface treatment type; however, significant effects for post system factor and for interaction between the 2 factors were observed. For the carbon fiber post, the ABSA surface treatment resulted in values significantly lower than the S surface treatment. SEM analysis of MTBS-tested specimens demonstrated adhesive and cohesive failures. CONCLUSIONS Airborne-particle abrasion did not influence the mechanical properties of the post; however, it produced undesirable surface changes, which could reduce the bond strength to resin cement. For the surface treatments studied, if silane is applied, the adhesive system and airborne-particle abrasion are not necessary.

In vitro analysis of the radiodensity of indirect composites and ceramic inlay systems and its influence on the detection of cement overhangs

The purpose of this study was to evaluate the radiodensity of indirect restorative systems and to determine its influence on detection of resin cement overhangs. Sixty sound molars with similar dimensions were selected, and MOD inlay preparations were made in a standardized fashion with 6° taper of the walls. Restorations were made with a porcelain, Duceram LFC, and with three indirect composites, Solidex, Artglass, and Targis. Digital radiographic images were taken before and after cementation of the inlays (Digora system) and were analyzed on two regions, the cervical and the isthmus floor. Digital radiodensity measurements were performed on standardized points symmetrically distributed over each restoration and tooth structure. Cement overhangs were detected through visual analysis by three evaluators. Data were statistically analyzed utilizing ANOVA following Tukey’s test (p < 0.05), showing that Solidex presented lower radiodensity than Duceram LFC, and both Artglass and Targis presented similar higher levels of radiodensity than the other groups. Radiodensity of cervical regions was always greater than for isthmus floor regions. Detection of the resin cement overhangs is easier observed on Solidex and Duceram LFC. Radiodensity is highly influenced by restorative material type and tooth regions. The detection of radiopaque resin cement overhangs is influenced by radiodensity of restorative materials.

Influence of method and period of storage on the microtensile bond strength of indirect composite resin restorations to dentine

This study evaluated the influence of the method and period of storage on the adhesive bond strength of indirect composite resin to bovine dentin. Ninety bovine incisors were stored in three different solutions: 0.2% thymol, 10% formalin, and 0.2% sodium azide, during 3 periods of storage: 7 days, 30 days and 6 months, resulting in 9 groups (n = 10). The roots were cut off and the buccal surface was ground with #600-grit silicon carbide paper. The surface was conditioned with 37% phosphoric acid for 15 s and a composite resin restoration (TPH Spectrum) was fixed using a one-bottle adhesive system (Adper Single Bond) and a dual-cured resinous cement (Rely X ARC) under a load of 500 g for 5 minutes. The samples were serially cut perpendicular to the bonded interface to obtain slices of 1.2 mm in thickness. Each slab was trimmed with a cylindrical diamond bur resulting in an hourglass shape with a cross-sectional area of approximately 1 mm(2). The microtensile bond strength (microTBS) testing was performed in a testing machine (EMIC 2000 DL) at a 0.5 mm/minute crosshead-speed until failure. After fracture, the specimens were examined under SEM to analyze the mode of fracture. muTBS Means were expressed in MPa and the data were analyzed by two-way ANOVA (3X3) and the Tukey test (alpha = 0.05). The storage times of 7 and 30 days produced no significant difference irrespective of the solution type. The formalin and thymol solutions, however, did have a negative influence on bond strength when the teeth were stored for 6 months.

Fracture strength of composite fixed partial denture using bovine teeth as a substitute for human teeth with or without fiber-reinforcement

This study evaluate the use of bovine teeth as a substitute for human teeth on fracture strength tests of composite fixed partial dentures (Cpd), with and without fiberglass reinforcement (Fg). Eighty teeth were selected, being 40 bovine incisors, 20 human premolars and 20 molars. Bovine incisors were ground to get a platform, simulating an occlusal surface of human molar. Teeth in pairs were embedded in polystyrene resin, simulating the periodontal ligament and divided in 4 groups: B-Cpd-Fg: bovine teeth restored with Cpd with Fg; B-Cpd-NFg: bovine teeth restored with Cpd without Fg; H-Cpd-Fg: human teeth restored Cpd with Fg; and H-Cpd-NFg: human teeth restored with Cpd without Fg. The Cpd were adhesively fixed and submitted to an axial compression load at the pontic center with a crosshead speed of 0.5 mm/min until fracture. Failure modes were assessed and classified. Data were subjected to two-way ANOVA and Tukeys HSD test (α=0.05). The tooth type had no influence on fracture strength and fracture mode. The inclusion of fiberglass increased significantly the fracture strength. The failure modes were more reparable in groups with fiber-reinforcement. Bovine teeth can be used as a substitute for human teeth in these types of fracture strength tests.

Surface Treatment of Glass Fiber and Carbon Fiber Posts: SEM Characterization

Morphology, etching patterns, surface modification, and characterization of 2 different fiber posts: Gfp, Glass fiber post; and Cfp, carbon fiber were investigated by SEM analysis, after different surface treatments. Thirty fiber posts, being 15 Gfp and 15 Cfp were divided into a 5 surface treatments (n = 3): C‐alcohol 70% (control); HF 4%‐immersion in 4% hydrofluoric acid for 1min; H3PO4 37%‐immersion in 37% phosphoric acid for 30s; H2O2 10%‐immersion in 10% hydrogen peroxide for 20 min; H2O2 24%‐immersion in 24% hydrogen peroxide for 10 min. Morphology, etching patterns, surface modification and surface characterization were acessed by SEM analysis. SEM evaluation revealed that the post surface morphology was modified following all treatment when compared with a control group, for both type of reinforced posts. HF seems to penetrate around the fibers of Gfp and promoted surface alterations. The Cfp surface seems to be inert to treatment with HF 4%. Dissolution of epoxy resin and exposure of the superficial fiber was observed in both post groups, regardless the type of reinforcing fiber, H2O2 in both concentrations. Relative smooth surface area was produced by H3PO4 37% treatment, but with similar features to untreated group. Surface treatment of fiber post is a determinant factor on micromechanical entanglement to resin composite core. Post treatment with hydrogen peroxide resulted strength of carbon and glass/epoxy resin fiber posts to resin composite core. Microsc. Res. Tech., 2011.