Francesco P. Mezzapesa
Instituto Politécnico Nacional
Network
Latest external collaboration on country level. Dive into details by clicking on the dots.
Publication
Featured researches published by Francesco P. Mezzapesa.
Optics Express | 2013
Francesco P. Mezzapesa; Lorenzo Columbo; Massimo Brambilla; Maurizio Dabbicco; S. Borri; Miriam S. Vitiello; Harvey E. Beere; D. A. Ritchie; Gaetano Scamarcio
We study the time dependence of the optical power emitted by terahertz and mid-IR quantum cascade lasers in presence of optical reinjection and demonstrate unprecedented continuous wave (CW) emission stability for strong feedback. We show that the absence of coherence collapse or other CW instabilities typical of diode lasers is inherently associated with the high value of the photon to carrier lifetime ratio and the negligible linewidth enhancement factor of quantum cascade lasers.
Optics Express | 2014
Francesca Di Niso; Caterina Gaudiuso; Teresa Sibillano; Francesco P. Mezzapesa; Antonio Ancona; Pietro Mario Lugarà
We study the incubation effect during laser ablation of stainless steel with ultrashort pulses to boost the material removal efficiency at high repetition rates. The multi-shot ablation threshold fluence has been estimated for two pulse durations, 650-fs and 10-ps, in a range of repetition rates from 50 kHz to 1 MHz. Our results show that the threshold fluence decreases with the number of laser pulses N due to damage accumulation mechanisms, as expected. Moreover, approaching the MHz regime, the onset of heat accumulation enhances the incubation effect, which is in turn lower for shorter pulses at repetition rates below 600 kHz. A saturation of the threshold fluence value is shown to occur for a significantly high number of pulses, and well fitted by a modified incubation model.
Tribology Letters | 2013
Michele Scaraggi; Francesco P. Mezzapesa; Giuseppe Carbone; Antonio Ancona; L. Tricarico
We present measurements of friction coefficient of lubricated laser surface textured (LST) microstructures with two different geometries. The former is made of a square lattice of microholes; the latter is constituted by a series of microgrooves. We analyze sliding velocities spanning more than two orders of magnitude to cover the entire range from the boundary to the hydrodynamic regime. In all cases, the interfacial pressure is limited to values (relevant to particular manufacturing processes) which allow to neglect macroscopic elastic deformations, piezo-viscosity and oil compressibility effects. The measured Stribeck curves data are compared with those obtained for the flat control surface and show that the regular array of microholes allows to reduce friction over the entire range of lubrication regimes with a decrease of about 50xa0% in the hydrodynamic regime. On the contrary, the parallel microgrooves lead to an increase of friction compared to the flat control surface with a maximum increase of about 80–100xa0% in the mixed lubrication regime. These remarkably opposite friction results are then explained with the aid of numerical simulations. Our findings confirm that LST may have cutting edge applications in engineering, not only in classical applications (e.g., to reduce piston-ring friction losses in internal combustion engines) but also, in particular, in technological processes, such as hydroforming, superplastic forming, where the mapping of the frictional properties of the mold has a crucial role in determining the final properties of the mechanical component.
IEEE Photonics Technology Letters | 2008
Simona Ottonelli; F. De Lucia; M. di Vietro; Maurizio Dabbicco; Gaetano Scamarcio; Francesco P. Mezzapesa
The simultaneous measurement of the linear displacement and two rotation angles (yaw and pitch) of a moving object using a laser sensor based on the self-mixing effect is reported. The laser head includes three commercial diode lasers equipped with monitor photodiodes. The target is a plane mirror attached to the moving object. The linear and angular resolutions are 0.7 mum and 0.8times10-30 (2.7 arcsec), respectively. The linearity of the sensor response has been verified over a range of 1 m and plusmn0.4deg. Using three retroreflector prisms with a diameter of 10 mm instead of the plane mirror, the angular range of yaw and pitch has been improved by one order of magnitude.
Optics Letters | 2011
Francesco P. Mezzapesa; Antonio Ancona; Teresa Sibillano; Francesco De Lucia; Maurizio Dabbicco; Pietro Mario Lugarà; Gaetano Scamarcio
We demonstrate that diode laser self-mixing interferometry can be exploited to instantaneously measure the ablation front displacement and the laser ablation rate during ultrafast microdrilling of metals. The proof of concept was obtained using a 50-μm-thick stainless steel plate as the target, a 120u2009ps/110u2009kHz microchip fiber laser as the machining source, and an 823u2009nm diode laser with an integrated photodiode as the probe. The time dependence of the hole penetration depth was measured with a 0.41u2009µm resolution.
Applied Physics Letters | 2014
Francesco P. Mezzapesa; L. L. Columbo; Massimo Brambilla; Maurizio Dabbicco; Miriam S. Vitiello; Gaetano Scamarcio
To monitor the density of photo-generated charge carriers on a semiconductor surface, we demonstrate a detectorless imaging system based on the analysis of the optical feedback in terahertz quantum cascade lasers. Photo-excited free electron carriers are created in high resistivity n-type silicon wafers via low power (≅40 mW/cm2) continuous wave pump laser in the near infrared spectral range. A spatial light modulator allows to directly reconfigure and control the photo-patterned intensity and the associated free-carrier density distribution. The experimental results are in good agreement with the numerical simulations.
Nature Physics | 2014
Simone Zanotto; Francesco P. Mezzapesa; G. Biasiol; Lorenzo Baldacci; Miriam S. Vitiello; Lucia Sorba; Raffaele Colombelli; Alessandro Tredicucci
The absorption properties of a resonator can be tuned by varying the phase between incoming coherent light beams. Such control is now shown under strong coupling conditions, allowing all incoming energy to be converted into polaritons. The ability to drive a system with an external input is a fundamental aspect of light–matter interaction. The key concept in many photonic applications is the ‘critical coupling’ condition1,2: at criticality, all the energy fed to the system is dissipated within the system itself. Although this idea was crucial to enhance the efficiency of many devices, it was never considered in the context of systems operating in a non-perturbative regime. In this so-called strong-coupling regime, the matter and light degrees of freedom are mixed into dressed states, leading to new eigenstates called polaritons3,4,5,6,7,8,9,10. Here we demonstrate that the strong-coupling regime and the critical coupling condition can coexist; in such a strong critical coupling situation, all the incoming energy is converted into polaritons. A general semiclassical theory reveals that such a situation corresponds to a special curve in the phase diagram of the coupled light–matter oscillators. In the case of a system with two radiating ports, the phenomenology shown is that of coherent perfect absorption (CPA; refsxa011, 12), which is then naturally understood in the framework of critical coupling. Most importantly, we experimentally verify polaritonic CPA in a semiconductor-based intersubband-polariton photonic crystal resonator. This result opens new avenues in polariton physics, making it possible to control the pumping efficiency of a system independent of the energy exchange rate between the electromagnetic field and the material transition.
Optics Express | 2011
Francesco P. Mezzapesa; Lorenzo Columbo; Massimo Brambilla; Maurizio Dabbicco; Antonio Ancona; Teresa Sibillano; Francesco De Lucia; Pietro Mario Lugarà; Gaetano Scamarcio
We demonstrate that a single all-optical sensor based on laser diode self-mixing interferometry can monitor the independent displacement of individual portions of a surface. The experimental evidence was achieved using a metallic sample in a translatory motion while partly ablated by a ps-pulsed fiber laser. A model based on the Lang-Kobayashi approach gives an excellent explanation of the experimental results.
Applied Physics Letters | 2012
Francesco P. Mezzapesa; Vincenzo Spagnolo; Antonio Ancona; Gaetano Scamarcio
The impact of quantum cascade lasers (QCLs) intrinsically high sensitivity to external optical feedback intended for sensing applications such as in-line ablation rate measurements is experimentally demonstrated. We developed a QCL-based sensor to assess the voltage modulation at the laser terminals induced by fast displacement of the ablation front during the process. This work shows that the detection range of our diagnostic system is only limited by the emission wavelength of the QCL probe source and the capability to measure ablation rates as high as 160u2009nm/pulse was reported. This sensing technique can be employed with the whole class of quantum cascade lasers, whose emission spans from mid-IR to THz spectral region, thus enabling the extension of its applications to ultra-fast laser ablation processes.
Sensors | 2012
Teresa Sibillano; Domenico Rizzi; Francesco P. Mezzapesa; Pietro Mario Lugarà; A.R. Konuk; Ronald G.K.M. Aarts; Bert Huis in 't Veld; Antonio Ancona
In this paper we describe a novel spectroscopic closed loop control system capable of stabilizing the penetration depth during laser welding processes by controlling the laser power. Our novel approach is to analyze the optical emission from the laser generated plasma plume above the keyhole, to calculate its electron temperature as a process-monitoring signal. Laser power has been controlled by using a quantitative relationship between the penetration depth and the plasma electron temperature. The sensor is able to correlate in real time the difference between the measured electron temperature and its reference value for the requested penetration depth. Accordingly the closed loop system adjusts the power, thus maintaining the penetration depth.