Francisco Falcone

Equivalent-circuit models for split-ring resonators and complementary split-ring resonators coupled to planar transmission lines

In this paper, a new approach for the development of planar metamaterial structures is developed. For this purpose, split-ring resonators (SRRs) and complementary split-ring resonators (CSRRs) coupled to planar transmission lines are investigated. The electromagnetic behavior of these elements, as well as their coupling to the host transmission line, are studied, and analytical equivalent-circuit models are proposed for the isolated and coupled SRRs/CSRRs. From these models, the stopband/passband characteristics of the analyzed SRR/CSRR loaded transmission lines are derived. It is shown that, in the long wavelength limit, these stopbands/passbands can be interpreted as due to the presence of negative/positive values for the effective /spl epsiv/ and /spl mu/ of the line. The proposed analysis is of interest in the design of compact microwave devices based on the metamaterial concept.

Effective negative-/spl epsiv/ stopband microstrip lines based on complementary split ring resonators

In this letter a super-compact stopband microstrip structure is proposed. The frequency gap is produced by an array of complementary split ring resonators (CSRRs)-a concept proposed here for the first time-etched on the ground plane. This behavior is interpreted as due to the presence of a negative effective dielectric permittivity in the vicinity of resonance. The resulting device produces a deep rejection frequency band with sharp cutoff, and a pass band that exhibits very low losses and good matching. Due to the sub-lambda operation of CSRRs, the electrical size of the device is very small.

Split ring resonator-based left-handed coplanar waveguide

In this letter, a planar left-handed propagating medium consisting of a coplanar waveguide (CPW) inductively coupled to split ring resonators (SRR) and periodically loaded with narrow metallic wires is proposed. The wires make the structure behave as a microwave plasma with a negative effective permittivity which covers a broad frequency range. The negative permeability required to achieve left-handed wave propagation is provided by the rings in the vicinity of their resonant frequency. The result is a structure which allows negative wave propagation in a narrow frequency band. The transmission coefficient measured in a fabricated prototype device exhibits very low insertion losses in the pass band and high-frequency selectivity. Since rings are much smaller than signal wavelength at resonance and can be easily tuned, SRR-CPW-based structures are of interest for the design of very compact microwave circuits based on left handedness.

Smart health: A context-aware health paradigm within smart cities

The new era of mobile health ushered in by the wide adoption of ubiquitous computing and mobile communications has brought opportunities for governments and companies to rethink their concept of healthcare. Simultaneously, the worldwide urbanization process represents a formidable challenge and attracts attention toward cities that are expected to gather higher populations and provide citizens with services in an efficient and human manner. These two trends have led to the appearance of mobile health and smart cities. In this article we introduce the new concept of smart health, which is the context-aware complement of mobile health within smart cities. We provide an overview of the main fields of knowledge that are involved in the process of building this new concept. Additionally, we discuss the main challenges and opportunities that s-Health would imply and provide a common ground for further research.

Miniaturized coplanar waveguide stop band filters based on multiple tuned split ring resonators

A novel compact stop band filter consisting of a 50 /spl Omega/ coplanar waveguide (CPW) with split ring resonators (SRRs) etched in the back side of the substrate is presented. By aligning SRRs with the slots, a high inductive coupling between line and rings is achieved, with the result of a sharp and narrow rejection band in the vicinity of the resonant frequency of the rings. In order to widen the stop band of the filter, several ring pairs tuned at equally spaced frequencies within the desired gap are cascaded. The frequency response measured in the fabricated prototype device exhibits pronounced slopes at either side of the stop band and near 0 dBs insertion loss outside that band. Since SRR dimensions are much smaller than signal wavelength, the proposed filters are extremely compact and can be used to reject frequency parasitics in CPW structures by simply patterning properly tuned SRRs in the back side metal. Additional advantages are easy fabrication and compatibility with MMIC or PCB technology.

Microwave filters with improved stopband based on sub-wavelength resonators

The main aim of this paper is to demonstrate the potentiality of sub-wavelength resonators, namely, split-ring resonators, complementary split-ring resonators, and related structures to the suppression of undesired spurious bands in microwave filters, a key aspect to improve their rejection bandwidths. The main relevant characteristics of the cited resonators are their dimensions (which can be much smaller than signal wavelength at resonance) and their high-Q factor. This allows us to design stopband structures with significant rejection levels, few stages, and small dimensions, which can be integrated within the filter active region. By this means, no extra area is added to the device, while the passband of interest is virtually unaltered. A wide variety of bandpass filters, implemented in both coplanar-waveguide and microstrip technologies, have been designed and fabricated by the authors. The characterization of these devices points out the efficiency of the proposed approach to improve filter responses with harmonic rejection levels near 40 dB in some cases. It is also important to highlight that the conventional design methodology for the filters holds. For certain configurations, the presence of the resonators slightly lowers the phase velocity at the frequencies of interest with the added advantage of some level of reduction in device dimensions.

Spurious passband suppression in microstrip coupled line band pass filters by means of split ring resonators

In this letter, spurious passband suppression in microstrip coupled line band pass filters by means of split ring resonators (SRRs) is demonstrated for the first time. By etching SRRs in the upper substrate side, in close proximity to conductor strip, strong magnetic coupling between line and rings arises at the resonant frequency of SRRs. This inhibits signal propagation in the vicinity of that frequency, allowing the rejection of undesired passbands by properly tuning SRRs. To test this novel technique, we have designed and fabricated two different SSRs-based filters. In one case, the rings have been designed to suppress only the first spurious band, and SRRs have been etched at both sides of the 50-/spl Omega/ access lines. For the other prototype, SRRs have been etched on the active device region (i.e., surrounding the parallel coupled lines) and have been tuned to eliminate the first and second undesired bands. The measured frequency responses for these devices confirm the efficiency of this technique to suppress frequency parasitics, with rejection levels near 40 dBs, leaving the passband unaltered. Since SRRs are small particles (with sub-wavelength dimensions at the resonant frequency), this approach does not add extra area to the final layouts. Moreover, the conventional design methodology of the filters holds.

Microstrip "wiggly-line" bandpass filters with multispurious rejection

A method to achieve the rejection of multiple spurious passbands in parallel-coupled-line microstrip bandpass filters is proposed. As it was previously demonstrated by the authors, using a continuous perturbation of the width of the coupled-lines following a sinusoidal law, the wave impedance can be modulated so that the first undesired harmonic passband of the filter is rejected, while the desired passband is maintained virtually unaltered. In this letter, the scope of the method is extended to reject multiple spurious passbands by employing different periods in each coupled-line section tuned to the different bands to be rejected. Simulated and measured data show that for an order-seven bandpass filter prototype, a rejection level exceeding 30 dB is obtained in the first four spurious passbands, while the desired pass-band is kept almost unaltered.

A new LC series element for compact bandpass filter design

A new LC series element based on a modified version of the split rings resonator introduced in is proposed. Owing to its small electrical size, the new open split ring resonator (OSRR) is a very attractive element for compact bandpass filter design. As an example, we have designed and fabricated a filter to produce a bandpass around the resonance frequency of the employed OSRRs. The filter bandwidth is controlled by the length of the transmission lines connecting the OSRRs. Sharp and deep out-of-band rejection is achieved by cascading several OSRRs. Circuit theory and electromagnetic based simulations reasonably agree with experiments.

Broadband spoof plasmons and subwavelength electromagnetic energy confinement on ultrathin metafilms

A complementary split ring resonator (CSRR)-based metallic layer is proposed as a route to mimic surface plasmon polaritons. A numerical analysis of the textured surface is carried out and compared to previous prominent topologies such as metal mesh, slit array, hole array, and Sievenpiper mushroom surfaces, which are studied as well from a transmission line perspective. These well-documented geometries suffer from a narrowband response, alongside, in most cases, metal thickness constraint (usually of the order of lambda/4) and non-subwavelength modal size as a result of the large dimensions of the unit cell (one dimensions is at least of the order of lambda/2). All of these limitations are overcome by the proposed CSRR-based surface. Besides, a planar waveguide is proposed as a proof of the potential of this CSRR-based metallic layer for spoof surface plasmon polariton guiding. Fundamental aspects aside, the structure under study is easy to manufacture by simple PCB techniques and it is expected to provide good performance within the frequency band from GHz to THz.