Mario Sorolla

Equivalent-circuit models for split-ring resonators and complementary split-ring resonators coupled to planar transmission lines

In this paper, a new approach for the development of planar metamaterial structures is developed. For this purpose, split-ring resonators (SRRs) and complementary split-ring resonators (CSRRs) coupled to planar transmission lines are investigated. The electromagnetic behavior of these elements, as well as their coupling to the host transmission line, are studied, and analytical equivalent-circuit models are proposed for the isolated and coupled SRRs/CSRRs. From these models, the stopband/passband characteristics of the analyzed SRR/CSRR loaded transmission lines are derived. It is shown that, in the long wavelength limit, these stopbands/passbands can be interpreted as due to the presence of negative/positive values for the effective /spl epsiv/ and /spl mu/ of the line. The proposed analysis is of interest in the design of compact microwave devices based on the metamaterial concept.

Effective negative-/spl epsiv/ stopband microstrip lines based on complementary split ring resonators

In this letter a super-compact stopband microstrip structure is proposed. The frequency gap is produced by an array of complementary split ring resonators (CSRRs)-a concept proposed here for the first time-etched on the ground plane. This behavior is interpreted as due to the presence of a negative effective dielectric permittivity in the vicinity of resonance. The resulting device produces a deep rejection frequency band with sharp cutoff, and a pass band that exhibits very low losses and good matching. Due to the sub-lambda operation of CSRRs, the electrical size of the device is very small.

Enhanced patch-antenna performance by suppressing surface waves using photonic-bandgap substrates

The microstrip patch antenna is a low-profile robust planar structure. A wide range of radiation patterns can be achieved with this type of antenna and, due to the ease of manufacture, is inexpensive compared with other types of antennas. However, patch-antenna designs have some limitations such as restricted bandwidth of operation, low gain, and a potential decrease in radiation efficiency due to surface-wave losses. In this paper, a photonic-bandgap (PBG) substrate for patch antennas is proposed, which minimizes the surface-wave effects. In order to verify the performance of this kind of substrate, a configuration with a thick substrate is analyzed. The PBG patch antenna shows significantly reduced levels of surface modes compared to conventional patch antennas, thus improving the gain and far-field radiation pattern.

New microstrip "Wiggly-Line" filters with spurious passband suppression

In this paper, we present a new parallel-coupled-line microstrip bandpass filter with suppressed spurious passband. Using a continuous perturbation of the width of the coupled lines following a sinusoidal law, the wave impedance is modulated so that the harmonic passband of the filter is rejected while the desired passband response is maintained virtually unaltered. This strip-width perturbation does not require the filter parameters to be recalculated and, this way, the classical design methodology for coupled-line microstrip filters can still be used. At the same time, the fabrication of the resulting filter layout does not involve more difficulties than those for typical coupled-line microstrip filters. To test this novel technique, 3rd-order Butterworth bandpass filters have been designed at 2.5 GHz, with a 10% fractional bandwidth and different values of the perturbation amplitude. It is shown that for a 47.5 % sinusoidal variation of the nominal strip width, a harmonic rejection of more than 40 dB is achieved in measurement while the passband at 2.5 GHz is almost unaltered.

Miniaturized coplanar waveguide stop band filters based on multiple tuned split ring resonators

A novel compact stop band filter consisting of a 50 /spl Omega/ coplanar waveguide (CPW) with split ring resonators (SRRs) etched in the back side of the substrate is presented. By aligning SRRs with the slots, a high inductive coupling between line and rings is achieved, with the result of a sharp and narrow rejection band in the vicinity of the resonant frequency of the rings. In order to widen the stop band of the filter, several ring pairs tuned at equally spaced frequencies within the desired gap are cascaded. The frequency response measured in the fabricated prototype device exhibits pronounced slopes at either side of the stop band and near 0 dBs insertion loss outside that band. Since SRR dimensions are much smaller than signal wavelength, the proposed filters are extremely compact and can be used to reject frequency parasitics in CPW structures by simply patterning properly tuned SRRs in the back side metal. Additional advantages are easy fabrication and compatibility with MMIC or PCB technology.

Microwave filters with improved stopband based on sub-wavelength resonators

The main aim of this paper is to demonstrate the potentiality of sub-wavelength resonators, namely, split-ring resonators, complementary split-ring resonators, and related structures to the suppression of undesired spurious bands in microwave filters, a key aspect to improve their rejection bandwidths. The main relevant characteristics of the cited resonators are their dimensions (which can be much smaller than signal wavelength at resonance) and their high-Q factor. This allows us to design stopband structures with significant rejection levels, few stages, and small dimensions, which can be integrated within the filter active region. By this means, no extra area is added to the device, while the passband of interest is virtually unaltered. A wide variety of bandpass filters, implemented in both coplanar-waveguide and microstrip technologies, have been designed and fabricated by the authors. The characterization of these devices points out the efficiency of the proposed approach to improve filter responses with harmonic rejection levels near 40 dB in some cases. It is also important to highlight that the conventional design methodology for the filters holds. For certain configurations, the presence of the resonators slightly lowers the phase velocity at the frequencies of interest with the added advantage of some level of reduction in device dimensions.

Spurious passband suppression in microstrip coupled line band pass filters by means of split ring resonators

In this letter, spurious passband suppression in microstrip coupled line band pass filters by means of split ring resonators (SRRs) is demonstrated for the first time. By etching SRRs in the upper substrate side, in close proximity to conductor strip, strong magnetic coupling between line and rings arises at the resonant frequency of SRRs. This inhibits signal propagation in the vicinity of that frequency, allowing the rejection of undesired passbands by properly tuning SRRs. To test this novel technique, we have designed and fabricated two different SSRs-based filters. In one case, the rings have been designed to suppress only the first spurious band, and SRRs have been etched at both sides of the 50-/spl Omega/ access lines. For the other prototype, SRRs have been etched on the active device region (i.e., surrounding the parallel coupled lines) and have been tuned to eliminate the first and second undesired bands. The measured frequency responses for these devices confirm the efficiency of this technique to suppress frequency parasitics, with rejection levels near 40 dBs, leaving the passband unaltered. Since SRRs are small particles (with sub-wavelength dimensions at the resonant frequency), this approach does not add extra area to the final layouts. Moreover, the conventional design methodology of the filters holds.

Enhanced millimeter-wave transmission through subwavelength hole arrays

We explore, both experimentally and theoretically, the existence in the millimeter-wave range of the phenomenon of extraordinary light transmission through arrays of subwavelength holes. We have measured the transmission spectra of several samples made on aluminum wafers by use of an AB Millimetre quasi-optical vector network analyzer in the wavelength range 4.2-6.5 mm. Clear signals of the existence of resonant light transmission at wavelengths close to the period of the array appear in the spectra.

Left-handed extraordinary optical transmission through a photonic crystal of subwavelength hole arrays

Metamaterial structures are artificial materials that show unconventional electromagnetic properties such as photonic band-gap, extraordinary optical transmission and left-handed propagation. Up to now, relations of photonic crystals and negative refraction have been shown as well as of photonic crystals and sub-wavelength hole arrays. Here we report a left-handed metamaterial engineered by a combination of sub-wavelength hole array plates periodically stacked to form a photonic crystal structure. It is shown the possibility of fine-tuning the metamaterial in order to permit extraordinary optical transmission and left-handed behaviour. Our work demonstrates the feasibility of engineering left-handed metamaterials by just drilling holes in metallic plates and brings together single structure photonic crystals, extraordinary optical transmission and left-handed behaviour.

Microstrip "wiggly-line" bandpass filters with multispurious rejection

A method to achieve the rejection of multiple spurious passbands in parallel-coupled-line microstrip bandpass filters is proposed. As it was previously demonstrated by the authors, using a continuous perturbation of the width of the coupled-lines following a sinusoidal law, the wave impedance can be modulated so that the first undesired harmonic passband of the filter is rejected, while the desired passband is maintained virtually unaltered. In this letter, the scope of the method is extended to reject multiple spurious passbands by employing different periods in each coupled-line section tuned to the different bands to be rejected. Simulated and measured data show that for an order-seven bandpass filter prototype, a rejection level exceeding 30 dB is obtained in the first four spurious passbands, while the desired pass-band is kept almost unaltered.