Gang Hee Han

Influence of Copper Morphology in Forming Nucleation Seeds for Graphene Growth

We report that highly crystalline graphene can be obtained from well-controlled surface morphology of the copper substrate. Flat copper surface was prepared by using a chemical mechanical polishing method. At early growth stage, the density of graphene nucleation seeds from polished Cu film was much lower and the domain sizes of graphene flakes were larger than those from unpolished Cu film. At later growth stage, these domains were stitched together to form monolayer graphene, where the orientation of each domain crystal was unexpectedly not much different from each other. We also found that grain boundaries and intentionally formed scratched area play an important role for nucleation seeds. Although the best monolayer graphene was grown from polished Cu with a low sheet resistance of 260 Ω/sq, a small portion of multilayers were also formed near the impurity particles or locally protruded parts.

Probing graphene grain boundaries with optical microscopy

Grain boundaries in graphene are formed by the joining of islands during the initial growth stage, and these boundaries govern transport properties and related device performance. Although information on the atomic rearrangement at graphene grain boundaries can be obtained using transmission electron microscopy and scanning tunnelling microscopy, large-scale information regarding the distribution of graphene grain boundaries is not easily accessible. Here we use optical microscopy to observe the grain boundaries of large-area graphene (grown on copper foil) directly, without transfer of the graphene. This imaging technique was realized by selectively oxidizing the underlying copper foil through graphene grain boundaries functionalized with O and OH radicals generated by ultraviolet irradiation under moisture-rich ambient conditions: selective diffusion of oxygen radicals through OH-functionalized defect sites was demonstrated by density functional calculations. The sheet resistance of large-area graphene decreased as the graphene grain sizes increased, but no strong correlation with the grain size of the copper was revealed, in contrast to a previous report. Furthermore, the influence of graphene grain boundaries on crack propagation (initialized by bending) and termination was clearly visualized using our technique. Our approach can be used as a simple protocol for evaluating the grain boundaries of other two-dimensional layered structures, such as boron nitride and exfoliated clays.

Layer-by-layer doping of few-layer graphene film.

We propose a new method of layer-by-layer (LbL) doping of thin graphene films. Large area monolayer graphene was synthesized on Cu foil by using the chemical vapor deposition method. Each layer was transferred on a polyethylene terephthalate substrate followed by a salt-solution casting, where the whole process was repeated several times to get LbL-doped thin layers. With this method, sheet resistance was significantly decreased up to approximately 80% with little sacrifice in transmittance. Unlike samples fabricated by topmost layer doping, our sample shows better environmental stability due to the presence of dominant neutral Au atoms on the surface which was confirmed by angle-resolved X-ray photoelectron spectroscopy. The sheet resistance of the LbL-doped four-layer graphene (11 x 11 cm(2)) was 54 Omega/sq at 85% transmittance, which meets the technical target for industrial applications.

Contact resistance between metal and carbon nanotube interconnects: Effect of work function and wettability

The contact resistance of 14 different electrode metals with the work function between 3.9 and 5.7 eV has been investigated for carbon nanotube (CNT) interconnects. We observed that the contact resistance was mainly influenced by the two following parameters: the wettability and the work function difference of electrode metal to CNT. Ti, Cr, and Fe with good wettability showed lower resistance than other metals. Furthermore, no dependence of the contact resistance on the work function difference has been observed. However, the contact resistance of Au, Pd, and Pt with poor wettability increased as the work function difference became larger.

Small hysteresis nanocarbon-based integrated circuits on flexible and transparent plastic substrate.

We report small hysteresis integrated circuits by introducing monolayer graphene for the electrodes and a single-walled carbon nanotube network for the channel. Small hysteresis of the device originates from a defect-free graphene surface, where hysteresis was modulated by oxidation. This uniquely combined nanocarbon material device with transparent and flexible properties shows remarkable device performance; subthreshold voltage of 220 mV decade(-1), operation voltage of less than 5 V, on/off ratio of approximately 10(4), mobility of 81 cm(2) V(-1) s(-1), transparency of 83.8% including substrate, no significant transconductance changes in 1000 times of bending test, and only 36% resistance decrease at a tensile strain of 50%. Furthermore, because of the nearly Ohmic contact nature between the graphene and carbon nanotubes, this device demonstrated a contact resistance 100 times lower and a mobility 20 times higher, when compared to an Au electrode.

Seeded growth of highly crystalline molybdenum disulphide monolayers at controlled locations

Monolayer transition metal dichalcogenides are materials with an atomic structure complementary to graphene but diverse properties, including direct energy bandgaps, which makes them intriguing candidates for optoelectronic devices. Various approaches have been demonstrated for the growth of molybdenum disulphide (MoS2) on insulating substrates, but to date, growth of isolated crystalline flakes has been demonstrated at random locations only. Here we use patterned seeds of molybdenum source material to grow flakes of MoS2 at predetermined locations with micrometre-scale resolution. MoS2 flakes are predominantly monolayers with high material quality, as confirmed by atomic force microscopy, transmission electron microscopy and Raman and photoluminescence spectroscopy. As the monolayer flakes are isolated at predetermined locations, transistor fabrication requires only a single lithographic step. Device measurements exhibit carrier mobility and on/off ratio that exceed 10 cm(2) V(-1) s(-1) and 10(6), respectively. The technique provides a path for in-depth physical analysis of monolayer MoS2 and fabrication of MoS2-based integrated circuits.

Enhanced Electric Double Layer Capacitance of Graphite Oxide Intercalated by Poly(sodium 4-styrensulfonate) with High Cycle Stability

We propose a new material for high power and high density supercapacitors with excellent cycle stability. Graphite oxide (PSS-GO) intercalated with poly(sodium 4-styrensulfonate) showed high performance of electric double layer capacitance (EDLC) compared to that of the pristine graphite oxide. Specific capacitance of the PSS-GO reached 190 F/g, and the energy density was much improved to 38 Wh/kg with a power density of 61 W/kg. Cycle test showed that the specific capacitance decreased by only 12% after 14860 cycles, providing excellent cyclic stability. The high EDLC performance of PSS-GO composite was attributed to the wide interlayer distance and simple pore structures accommodating fast ion kinetics.

Fano Resonance and Spectrally Modified Photoluminescence Enhancement in Monolayer MoS2 Integrated with Plasmonic Nanoantenna Array

The manipulation of light-matter interactions in two-dimensional atomically thin crystals is critical for obtaining new optoelectronic functionalities in these strongly confined materials. Here, by integrating chemically grown monolayers of MoS2 with a silver-bowtie nanoantenna array supporting narrow surface-lattice plasmonic resonances, a unique two-dimensional optical system has been achieved. The enhanced exciton-plasmon coupling enables profound changes in the emission and excitation processes leading to spectrally tunable, large photoluminescence enhancement as well as surface-enhanced Raman scattering at room temperature. Furthermore, due to the decreased damping of MoS2 excitons interacting with the plasmonic resonances of the bowtie array at low temperatures stronger exciton-plasmon coupling is achieved resulting in a Fano line shape in the reflection spectrum. The Fano line shape, which is due to the interference between the pathways involving the excitation of the exciton and plasmon, can be tuned by altering the coupling strengths between the two systems via changing the design of the bowties lattice. The ability to manipulate the optical properties of two-dimensional systems with tunable plasmonic resonators offers a new platform for the design of novel optical devices with precisely tailored responses.

Fast growth of graphene patterns by laser direct writing

Rapid single-step fabrication of graphene patterns was developed using laser-induced chemical vapor deposition (LCVD). A laser beam irradiates a thin nickel foil in a CH4 and H2 environment to induce a local temperature rise, thereby allowing the direct writing of graphene patterns in precisely controlled positions at room temperature. Line patterns can be achieved with a single scan without pre- or postprocesses. Surprisingly, the growth rate is several thousand times faster than that of general CVD methods. The discovery and development of the LCVD growth process provide a route for the rapid fabrication of graphene patterns for various applications.

Biexciton Emission from Edges and Grain Boundaries of Triangular WS2 Monolayers

Monolayer tungsten disulfides (WS2) constitute a high quantum yield two-dimensional (2D) system, and can be synthesized on a large area using chemical vapor deposition (CVD), suggesting promising nanophotonics applications. However, spatially nonuniform photoluminescence (PL) intensities and peak wavelengths observed in single WS2 grains have puzzled researchers, with the origins of variation in relative contributions of excitons, trions, and biexcitons to the PL emission not well understood. Here, we present nanoscale PL and Raman spectroscopy images of triangular CVD-grown WS2 monolayers of different sizes, with these images obtained under different temperatures and values of excitation power. Intense PL emissions were observed around the edges of individual WS2 grains and the grain boundaries between partly merged WS2 grains. The predominant origin of the main PL emission from these regions changed from neutral excitons to trions and biexcitons with increasing laser excitation power, with biexcitons completely dominating the PL emission for the high-power condition. The intense PL emission and the preferential formation of biexcitons in the edges and grain boundaries of monolayer WS2 were attributed to larger population of charge carriers caused by the excessive incorporation of growth promoters during the CVD, suggesting positive roles of excessive carriers in the PL efficiency of TMD monolayers. Our comprehensive nanoscale spectroscopic investigation sheds light on the dynamic competition between exciton complexes occurring in monolayer WS2, suggesting a rich variety of ways to engineer new nanophotonic functions using 2D transition metal dichalcogenide monolayers.