Gastón A. Crespo

Ion-selective electrodes using carbon nanotubes as ion-to-electron transducers.

This study developed a new type of all-solid-state ion-selective electrode based on a transducing layer of a network of single-walled carbon nanotubes. The extraordinary capacity of carbon nanotubes to promote electron transfer between heterogeneous phases made the presence of electroactive polymers or any other ion-to-electron-transfer promoter unnecessary. The new transducer layer was characterized by environmental scanning electron microscopy and electrochemical impedance spectroscopy. The stability of the electrical potential of the new solid-contact electrode was examined by performing current-reversal chronopotentiometry, and the influence of the interfacial water film was assessed by the potentiometric water layer test. The performance of the new electrode was evaluated by determining K+ with an ion-selective membrane that contained the well-known valinomycin ion carrier. The new electrode had a Nernstian slope (58.4 mV/decade), dynamic ranges of four logarithmic units, and selectivities and limits of detection comparable to other solid-contact electrodes. The short response time (less than 10 s for activities higher than 10(-5.5) M) and the stability of the signal over several days makes these new electrodes very promising candidates for attaining true miniaturization.

Transduction mechanism of carbon nanotubes in solid-contact ion-selective electrodes.

Porous carbon materials and carbon nanotubes were recently used as solid contacts in ion-selective electrodes (ISE), and the signal transduction mechanism of these carbon-based materials is therefore of great interest. In this work the ion-to-electron transduction mechanism of carbon nanotubes is studied by using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). Single-walled carbon nanotubes (SWCNT) are deposited on glassy carbon (GC) disk electrodes by repetitive spraying, resulting in SWCNT layers with thicknesses of 10, 35, and 50 mum. The impedance spectra of these GC/SWCNT electrodes in contact with aqueous electrolyte solution show a very small resistance and a large bulk capacitance that is related to a large effective double layer at the SWCNT/electrolyte interface. Interestingly, the impedance response of GC/SWCNT is very similar to that of poly(3,4-ethylenedioxythiophene) (PEDOT) film electrodes studied earlier under the same experimental conditions. The same equivalent circuit is valid for both types of materials. The reason is that both materials can be described schematically as an asymmetric capacitor where one side is formed by electronic charge (electrons/holes) in the SWCNT wall or along the conjugated polymer chain of PEDOT and the other side is formed by ions (anions/cations) in the solution (or in the ion-selective membrane when used as a solid contact in ISE).

Paper-Based Ion-Selective Potentiometric Sensors

A new approach to develop ultra low-cost, robust, rugged, and disposable potentiometric sensors is presented. A suspension of carbon nanotubes in a water-surfactant mixture (carbon nanotubes ink) is applied on conventional filter papers to turn them into conductive papers, which are then used as a substrate to build ion-selective electrodes. The electrodes are made by drop casting a membrane on a small circular area of the conductive paper. In this way, the carbon nanotubes act as both electric conductors and ion-to-electron transducers of the potentiometric signal. Electrodes for sensing K(+), NH(4)(+), and pH were built and tested using this approach, and the results were compared with classical solid-state ion selective electrodes using carbon nanotubes as transducers and glassy carbon as a substrate. In all cases, the analytical performance (sensitivity, linear ranges, limits of detection, selectivity, etc.) of these disposable paper electrodes was similar to that obtained for the more conventional type of ion-selective-electrodes. This opens new avenues for very low-cost platforms for generation of chemical information.

Ion-selective electrodes using multi-walled carbon nanotubes as ion-to-electron transducers for the detection of perchlorate

A solid contact ion-selective electrode using for the first time multi-walled carbon nanotubes (MWCNT) for the transducer material was developed for detecting perchlorate in water. To demonstrate the excellent ion-to electron transducer ability of the MWCNTs, a 15 microm thick layer of carboxylated MWCNT was deposited between an acrylic membrane selective to perchlorate ions and a glassy carbon rod used as the substrate and electrical conductor. The electrodes showed a Nernstian response of 57 mV decade(-1) (standard deviation of 3 mV decade(-1) over time and different electrodes) across a wide linear range of 10(-6) to 10(-2) M. The limit of detection was 10(-7.4) M of perchlorate. The response time was less than 10 s for activities higher than 10(-6) M and the intermediate-term potential stability shows a small drift of 0.22 mV h(-1) recorded over 5 hours. The electrode displays a selectivity comparable to liquid-contacted ISEs containing the same membrane.

Potentiometric strip cell based on carbon nanotubes as transducer layer: toward low-cost decentralized measurements.

In this study, we developed a potentiometric planar strip cell based on single-walled carbon nanotubes that aims to exploit the attributes of solid-contact ion-selective electrodes for decentralized measurements. That is, the ion-selective and reference electrodes have been simultaneously miniaturized onto a plastic planar substrate by screen-printing and drop-casting techniques, obtaining disposable strip cells with satisfactory performance characteristics (i.e., the sensitivity is 57.4 ± 1.3 mV/dec, the response time is ≤30 s within the linear range from log a(K+) = -5 to -2, and the limit of detection is -6.5), no need of maintenance during long dry storage, quick signal stabilization, and light insensitivity in short-term measurements. We also show how the new potentiometric strip cell makes it possible to perform decentralized and rapid determinations of ions in real samples, such as saliva or beverages.

Nanostructured materials in potentiometry.

Potentiometry is a very simple electrochemical technique with extraordinary analytical capabilities. It is also well known that nanostructured materials display properties which they do not show in the bulk phase. The combination of the two fields of potentiometry and nanomaterials is therefore a promising area of research and development. In this report, we explain the fundamentals of potentiometric devices that incorporate nanostructured materials and we highlight the advantages and drawbacks of combining nanomaterials and potentiometry. The paper provides an overview of the role of nanostructured materials in the two commonest potentiometric sensors: field-effect transistors and ion-selective electrodes. Additionally, we provide a few recent examples of new potentiometric sensors that are based on receptors immobilized directly onto the nanostructured material surface. Moreover, we summarize the use of potentiometry to analyze processes involving nanostructured materials and the prospects that the use of nanopores offer to potentiometry. Finally, we discuss several difficulties that currently hinder developments in the field and some future trends that will extend potentiometry into new analytical areas such as biology and medicine.

Reversible Sensing of the Anticoagulant Heparin with Protamine Permselective Membranes

A permselective membrane electrode allows the rapid and operationally reversible detection of the polycationic polypeptide protamine in physiological samples. Anticoagulant levels of heparin can be measured in undiluted whole blood by adding a known excess of its antidote protamine to discrete blood samples.

Paper-Based Thin-Layer Coulometric Sensor for Halide Determination

We report on a paper-based analytical device (PAD) for the exhaustive, and therefore absolute, determination of halides in a range of diverse water samples and food supplements. A mixture of chloride, bromide, and iodide ions is assessed in a wide range of concentrations, specifically, from 10(-4.8) to 0.1 M for bromide and iodide and from 10(-4.5) to 0.6 M for chloride, with a limit of detection of 10(-5) M. As a result of a careful optimization of the electrochemical cell, a thin layer made of cellulose paper (75-μm thickness), a cation-exchange Donnan exclusion membrane (FKL), and a silver-foil working electrode were selected as optimum materials. Cyclic voltammetry (from 0 to 0.8 V) was chosen as the interrogation technique to impose the exhaustive oxidative plating and re-reduction of halides on the silver element, accompanied by outward and inward counterion fluxes. The scan rate plays an important role in the ability of the technique to resolve mixtures of ions. Moderate scan rates (10 mV s(-1)) provide a suitable compromise between sensitivity, limit of detection, and resolution. This paper-based microfluidic device is extremely simple in terms of manipulation, cost, and contamination risk. Paper is an excellent basis for the establishment of a confined thin aqueous layer, the construction of disposable halide sensors, and portability for measuring outside the controlled laboratory environment. A discussion of the relevant analytical characteristics is presented herein, followed by a demonstration of halide assessment in water samples (sea, tap, river, and mineral waters) and food supplements enriched with iodide and chloride as early examples.

All-Solid-State Potentiometric Sensors with a Multiwalled Carbon Nanotube Inner Transducing Layer for Anion Detection in Environmental Samples

While ion to electron transducing layers for the fabrication of potentiometric membrane electrodes for the detection of cations have been well established, similar progress for the sensing of anions has not yet been realized. We report for this reason on a novel approach for the development of all-solid-state anion selective electrodes using lipophilic multiwalled carbon nanotubes (f-MWCNTs) as the inner ion to electron transducing layer. This material can be solvent cast, as it conveniently dissolves in tetrahydrofuran (THF), an important advantage to develop uniform films without the need for using surfactants that might deteriorate the performance of the electrode. Solid contact sensors for carbonate, nitrate, nitrite, and dihydrogen phosphate are fabricated and characterized, and all exhibit comparable analytical characteristics to the inner liquid electrodes. For example, the carbonate sensor exhibits a Nernstian slope of 27.2 ± 0.8 mV·dec(-1), a LOD = 2.3 μM, a response time of 1 s, a linear range of four logarithmic units, and a medium-term stability of 0.04 mV·h(-1) is obtained in a pH 8.6 buffered solution. Water layer test, reversibility, and selectivity for chloride, nitrate, and hydroxide are also reported. The excellent properties of f-MWCNTs as a transducer are contrasted to the deficient performance of poly(3-octyl-thiophene) (POT) for carbonate detection. This is evidenced both with a significant drift in the potentiometric measures as well as a pronounced sensitivity to light (either sunlight or artificial light). This latter aspect may compromise its potential for environmental in situ measurements (night/day cycles). The concentration of carbonate is determined in a river sample (Arve river, Geneva) and compared to a reference method (automatic titrator with potentiometric pH detection). The results suggest that nanostructured materials such as f-MWCNTs are an attractive platform as a general ion-to-electron transducer for anion-selective electrodes.

Determination of choline and derivatives with a solid-contact ion-selective electrode based on octaamide cavitand and carbon nanotubes

A new solid-contact ion-selective electrode has been developed for determining choline and derivatives in aqueous solutions. The backbone of this new potentiometric sensor is the conjunction of the cavitand receptor, as the molecular recognition element, and a network of non-carboxylated single-walled carbon nanotubes, acting as a solid transducer material. The octaamide cavitand, a synthetic receptor that is highly selective for biologically important trimethyl alkylammonium cations such as choline, acetylcholine or carnitine, makes the selective determination of these compounds possible for the first time. The guest-host interaction takes place in the acrylate ion-selective membrane of the solid-contact electrode. The sensor was characterized by electrochemical impedance spectroscopy and environmental scanning electron microscopy. The new electrode displays a nearly Nernstian slope (57.3+/-1.0 mV/decade) and very stable behaviour (DeltaE/Deltat=224 muVh(-1)) throughout the dynamic range (10(-5) to 10(-1)M). The limit of detection of 10(-6.4)M and the high selectivities obtained will enable choline and derivatives to be determined in biological samples. Finally, the stability of the electrical potential of the new solid-contact electrode was examined by performing current-reversal chronopotentiometry and the influence of the interfacial water film was evaluated by the potentiometric water layer test.