Georgios Fontaras

Effects of low concentration biodiesel blends application on modern passenger cars. Part 3: Impact on PAH, nitro-PAH, and oxy-PAH emissions

This study explores the impact of five different types of methyl esters on polycyclic aromatic hydrocarbon (PAH), nitrated-PAH and oxygenated PAH emissions. The measurements were conducted on a chassis dynamometer, according to the European regulation. Each of the five different biodiesels was blended with EN590 diesel at a proportion of 10-90% v/v (10% biodiesel concentration). The vehicle was a Euro 3 compliant common-rail diesel passenger car. Emission measurements were performed over the NEDC and compared with those of the real traffic-based Artemis driving cycles. The experimental results showed that the addition of biodiesel led to some important increases in low molecular-weight PAHs (phenanthrene and anthracene) and to both increases and reductions in large PAHs which are characterised by their carcinogenic and mutagenic properties. Nitro-PAHs were found to reduce with biodiesel whereas oxy-PAH emissions presented important increases with the biodiesel blends. The impact of biodiesel source material was particularly clear on the formation of PAH compounds. It was found that most PAH emissions decreased as the average load and speed of the driving cycle increased. Cold-start conditions negatively influenced the formation of most PAH compounds. A similar trend was observed with particulate alkane emissions.

DEVELOPMENT AND REVIEW OF EURO 5 PASSENGER CAR EMISSION FACTORS BASED ON EXPERIMENTAL RESULTS OVER VARIOUS DRIVING CYCLES

The emissions of CO2 and regulated pollutants (NOx, HC, CO, PM) of thirteen Euro 5 compliant passenger cars (seven gasoline, six Diesel) were measured on a chassis dynamometer. The vehicles were driven repeatedly over the European type-approval driving cycle (NEDC) and the more dynamic WMTC and CADC driving cycles. Distance-specific emission factors were derived for each pollutant and sub-cycle, and these were subsequently compared to the corresponding emission factors provided by the reference European models used for vehicle emission inventory compilation (COPERT and HBEFA) and put in context with the applicable European emission limits. The measured emissions stayed below the legal emission limits when the type-approval cycle (NEDC) was used. Over the more dynamic cycles (considered more representative of real-world driving) the emissions were consistently higher but in most cases remained below the type-approval limit. The high NOx emissions of Diesel vehicles under real-world driving conditions remain the main cause for environmental concern regarding the emission profile of Euro 5 passenger cars. Measured emissions of NOx exceeded the type-approval limits (up to 5 times in extreme cases) and presented significantly increased average values (0.35 g/km for urban driving and 0.56 g/km for motorway driving). The comparison with the reference models showed good correlation in all cases, a positive finding considering the importance of these tools in emission monitoring and policy-making processes.

Effects of low concentration biodiesel blend application on modern passenger cars. Part 1: Feedstock impact on regulated pollutants, fuel consumption and particle emissions

Five biodiesels from different feedstocks (rapeseed, soy, sunflower, palm, and used fried oils) blended with diesel at 10% vol. ratio (B10), were tested on a Euro 3 common-rail passenger car. Limited effects (-2% to +4%) were observed on CO(2) emissions. CO and HC emissions increased between 10% and 25% on average, except at high speed - high power where emissions were too low to draw conclusions. NOx emissions increased by up to 20% for two out of the five blends, decreased by up to 15% for two other blends, and remained unchanged for one blend. Particulate matter (PM) was reduced for all blends by up to 25% and the reductions were positively correlated with the extent of biodiesel saturation. PM reductions are associated with consistent reductions in non-volatile particle number. A variable behaviour in particle number is observed when volatile particles are also accounted.

Effects of low concentration biodiesel blends application on modern passenger cars. Part 2: Impact on carbonyl compound emissions

Today in most European member states diesel contains up to 5% vol biodiesel. Since blending is expected to increase to 10% vol, the question arises, how this higher mixing ratio will affect tailpipe emissions particularly those linked to adverse health effects. This paper focuses on the impact of biodiesel on carbonyl compound emissions, attempting also to identify possible relationship between biodiesel feedstock and emissions. The blends were produced from five different feedstocks, commonly used in Europe. Measurements were conducted on a Euro 3 common-rail passenger car over various driving cycles. Results indicate that generally the use of biodiesel at low concentrations has a minor effect on carbonyl compound emissions. However, certain biodiesels resulted in significant increases while others led to decreases. Biodiesels associated with increases were those derived from rapeseed oil (approx. 200%) and palm oil (approx. 180%), with the highest average increases observed at formaldehyde and acroleine/acetone.

Assessment of on-road emissions of four Euro V diesel and CNG waste collection trucks for supporting air-quality improvement initiatives in the city of Milan

This paper summarizes the results of an extensive experimental study aiming to evaluate the performance and pollutant emissions of diesel and CNG waste collection trucks under realistic and controlled operating conditions in order to support a fleet renewal initiative in the city of Milan. Four vehicles (1 diesel and 3 CNG) were tested in two phases using a portable emission measurement system. The first phase included real world operation in the city of Milan while the second involved controlled conditions in a closed track. Emissions recorded from the diesel truck were on average 2.4 kg/km for CO(2), 0.21 g/km for HC, 7.4 g/km for CO, 32.3 g/km for NO(x) and 46.4 mg/km for PM. For the CNG the values were 3.6 kg/km for CO(2), 2.19 g/km for HC, 15.8 g/km for CO, 4.38 g/km for NO(x) and 11.4 mg/km for PM. CNG vehicles presented an important advantage with regards to NO(x) and PM emissions but lack the efficiency of their diesel counterparts when it comes to CO, HC and particularly greenhouse gas emissions. This tradeoff needs to be carefully analyzed prior to deciding if a fleet should be shifted towards either technology. In addition it was shown that existing emission factors, used in Europe for environmental assessment studies, reflect well the operation for CNG but were not so accurate when it came to the diesel engine truck particularly for CO(2) and NO(x). With regard to NO(x), it was also shown that the limits imposed by current emission standards are not necessarily reflected in real world operation, under which the diesel vehicle presented almost 4 times higher emissions. Regarding CO(2), appropriate use of PEMS data and vehicle information allows for accurate emission monitoring through computer simulation.

Gaseous Emissions from Light-Duty Vehicles: Moving from NEDC to the New WLTP Test Procedure.

The Worldwide Harmonized Light Duty Test Procedure (WLTP), recently issued as GTR15 by UNECE-WP29, is designed to check the pollutant emission compliance of Light Duty Vehicles (LDVs) around the world and to establish the reference vehicle fuel consumption and CO2 performance. In the course of the development of WLTP, the Joint Research Center (JRC) of the European Commission has tested gaseous emissions of twenty-one Euro 4-6 gasoline and diesel vehicles, on both the current European type approval test procedure (NEDC) and the progressive versions of the WLTP. The results, which should be regarded just as an initial and qualitative indication of the trends, demonstrated minimal average differences between CO2 emissions over the NEDC and WLTP. On the other hand, CO2 emissions measured at JRC on the NEDC were on average 9% higher than the respective type approval values, therefore suggesting that for the tested vehicles, CO2 emissions over WLTP were almost 10% higher than the respective NEDC type approval values. That difference is likely to increase with application of the full WLTP test procedure. Measured THC emissions from most vehicles stayed below the legal emission limits and in general were lower under the WLTP compared to NEDC. Moving from NEDC to WLTP did not have much impact on NOx from gasoline vehicles and CO from diesel vehicles. On the contrary, NOx from diesel vehicles and CO from low-powered gasoline vehicles were significantly higher over the more dynamic WLTP and in several cases exceeded the emission limits. Results from this study can be considered indicative of emission patterns of modern technology vehicles and useful to both policy makers and vehicle manufacturers in developing future emission policy/technology strategies.

Aerodynamic and Mobility Size Distribution Measurements to Reveal Biodiesel Effects on Diesel Exhaust Aerosol

This article examines the effect of biodiesel blends on the exhaust aerosol from a Euro 3 passenger car. Five different feedstock oils (soybean, palm, sunflower, rapeseed, and used frying oil) were used to produce fuels with 10% vol. content in biodiesel (B10). Use of the B10 blends led to a systematic reduction of PM mass emissions in the range of ∼9% (rapeseed) to 23% (used frying oil) on average. The combination of particle size distributions based on the aerodynamic and the mobility diameters led to the estimation of the fractal dimension (DF) for non-volatile particles. This was found to range from 2.52 for the baseline (fossil) fuel to 2.62 for the palm oil blend, suggesting that biodiesel can affect the particle morphology, even at this low blending ratio. The differences were statistically significant. The increase of the DF is translated to more compact particle structure, which in turn denotes lower specific surface area. The volatile fraction of PM lies within a range of 1–9% when fossil diesel fuel is employed. Use of palm, sunflower and rapeseed B10 blends results to PM that contain up to 28% volatile particulate mass. The higher emissions of volatile components together with the lower specific area of non-volatile particles, promotes the formation of volatile particles, especially at high speed conditions. This increases the total particle population under motorway driving by up to three times over the baseline levels.

Development of the Worldwide Harmonized Test Procedure for Light-Duty Vehicles: Pathway for Implementation in European Union Legislation

To assess vehicle performance on criteria compounds, carbon dioxide emissions, and fuel energy consumption, laboratory tests are generally carried out. During these tests, a vehicle is driven on a chassis dynamometer (which simulates the resistances the vehicle encounters during its motion) to follow a predefined test cycle. In addition, all conditions for running a test must strictly adhere to a predefined test procedure. The procedure is necessary to ensure that all tests are carried out in a comparable way, following the requirements set by the relevant legislation. Test results are used to assess vehicle compliance with emissions limits or to evaluate the fuel consumption that will be communicated to customers. Every region in the world follows its own approach in carrying out these types of tests. The variations in approaches have resulted in a series of drawbacks for vehicle manufacturers and regulating authorities, leading to a plethora of different conditions and results. As a step toward the harmonization of the test procedures, the United Nations Economic Commission for Europe launched a project in 2009 for the development of a worldwide harmonized light-duty test procedure (WLTP), including a new test cycle. The objective of the study reported here was to provide a brief description of WLTP and outline the plausible pathway for its introduction in European legislation.

Vehicle Emission Factors of Solid Nanoparticles in the Laboratory and on the Road Using Portable Emission Measurement Systems (PEMS)

Emission inventories are used to quantify sources and identify trends in the emissions of air pollutants. They use vehicle-specific emission factors that are typically determined in the laboratory, through remote-sensing, vehicle chasing experiments and, more recently, on-board Portable Emission Measurement Systems (PEMS). Although PEMS is widely applied to measure gaseous pollutants, their application to Solid Particle Number (SPN) emissions is new. In this paper, we discuss the current status of determining SPN emission factors both on the chassis dynamometer and on-road using PEMS-SPN. First, we determine the influence of the measurement equipment, ambient temperature, driving style and cycle characteristics, and the extra mass of the PEMS equipment on the SPN emissions. Afterward, we present the SPN emissions under type-approval conditions as well as on the road of two heavy-duty diesel vehicles equipped with Diesel Particulate Filter (DPF) (one Euro VI), two light-duty diesel vehicles equipped with DPF, one light-duty vehicle equipped with a Port Fuel Injection engine (PFI), and seven Gasoline Direct Injection (GDI) passenger cars (two Euro 6). We find that cold-start and strong accelerations tend to substantially increase SPN emissions. The two heavy-duty vehicles showed emissions around 2×10^13 p/km (Euro V truck) and 6×10^10 p/km (Euro VI truck), respectively. One of the DPF-equipped light-duty vehicles showed emissions of 8×10^11 p/km, while the other one had one order of magnitude lower emissions. The PFI car had SPN emissions slightly higher than 1×10^12 p/km. The emissions of GDI cars spanned approximately from 8×10^11 p/km to 8×10^12 p/km. For the cars without DPF, the SPN emissions remained within a factor of two of the laboratory results. This factor was on average around 0.8 for the Euro 6 and 1.6 for the Euro 5 GDIs. The DPF equipped vehicles showed a difference of almost one order of magnitude between laboratory and on-road tests due to the different DPF fill state and passive regeneration during the tests. The findings of this study can (i) help improving the on SPN emissions and (ii) assist policy makers in designing effective test procedures for measuring SPN emissions of vehicles under real-world driving conditions.

The design of a Formula Student race car: a case study:

Abstract This paper presents the procedure followed in order to design the first Formula Student race car of the Aristotle University of Thessaloniki, Greece. Despite the restrictions imposed by the Formula SAE rules, the designer has a broad range of freedom in creativity and innovativeness. The design concept of the main vehicle parts, such as the frame and the suspension, is described and the design objectives and assumptions are analysed. The paper also focuses on several new features regarding the suspension adjustments, the steering system, and the engine modifications. Following this procedure, it was made possible to build a competitive and reliable car in a period of just 9 months.