Gilberto Vilanova Queiroz

Comparative study of classic friction among different archwire ligation systems

OBJECTIVE: To describe and compare three alternative methods for controlling classical friction: Self-ligating brackets (SLB), special brackets (SB) and special elastomeric ligatures (SEB). METHODS: The study compared Damon MX, Smart Clip, In-Ovation and Easy Clip self-ligating bracket systems, the special Synergy brackets and Morellis twin bracket with special 8-shaped elastomeric ligatures. New and used Morelli brackets with new and used elastomeric ligatures were used as control. All brackets had 0.022 x 0.028-in slots. 0.014-in nickel-titanium and stainless steel 0.019 x 0.025-in wires were tied to first premolar steel brackets using each archwire ligation method and pulled by an Instron machine at a speed of 0.5 mm/minute. Prior to the mechanical tests the absence of binding in the device was ruled out. Statistical analysis consisted of the Kruskal-Wallis test and multiple non-parametric analyses at a 1% significance level. RESULTS: When a 0.014-in archwire was employed, all ligation methods exhibited classical friction forces close to zero, except Morelli brackets with new and old elastomeric ligatures, which displayed 64 and 44 centiNewtons, respectively. When a 0.019 x 0.025-in archwire was employed, all ligation methods exhibited values close to zero, except the In-Ovation brackets, which yielded 45 cN, and the Morelli brackets with new and old elastomeric ligatures, which displayed 82 and 49 centiNewtons, respectively. CONCLUSIONS: Damon MX, Easy Clip, Smart Clip, Synergy bracket systems and 8-shaped ligatures proved to be equally effective alternatives for controlling classical friction using 0.014-in nickel-titanium archwires and 0.019 x 0.025-in steel archwires, while the In-Ovation was efficient with 0.014-in archwires but with 0.019 x 0.025-in archwires it exhibited friction that was similar to conventional brackets with used elastomeric ligatures.

Does self-ligating brackets type influence the hysteresis, activation and deactivation forces of superelastic NiTi archwires?

OBJECTIVE To compare hysteresis, activation and deactivation forces produced by first-order deformation of Contour 0.014-in NiTi wire (Aditek, Brazil) in four brands of self-ligating brackets: Damon MX, Easy Clip, Smart Clip and In-Ovation. METHODS Activation and deactivation forces were measured in an Instron universal tensile machine at 3 mm/minute speed to a total displacement of 4 mm. Tests were repeated eight times for each bracket/wire combination. Statistical analysis comprised ANOVA and Tukeys multiple comparisons test. RESULTS Using a 4-mm deformation, mean activation forces increased in the following order: Damon = 222 gf, Easy Clip = 228 gf, In-Ovation = 240 gf and Smart Clip = 306 gf. The same order was observed for mean hysteresis values, i.e., 128 gf, 140 gf, 150 gf and 206 gf, respectively. The respective values of deactivation forces for the Damon, Easy Clip, In-Ovation and Smart Clip brackets were 94 gf, 88 gf, 90 gf and 100 gf. CONCLUSIONS Brackets with higher activation forces were accompanied by higher hysteresis values, which resulted in clinically similar deactivation forces, regardless of the type of self-ligating brackets used.

Evaluation of radiographic magnification in lateral cephalograms obtained with different X-ray devices: experimental study in human dry skull

OBJECTIVE The purpose of this study was to evaluate the influence of the magnification factor of the radiographic image in angular, linear and proportional measurements. METHODS From a dried human skull where metallic spheres with predetermined size were fixed (1.0 mm), 14 radiographs were obtained in devices from three different manufacturers: Panoura, Instrumentarium and Tomeceph. The Pearson correlation test was used to investigate the relationship between the rate of radiographic magnification and the cephalometric measurements assessed. RESULTS According to the results, the linear measurements showed a high positive correlation, pointing out great influence of the magnification factor, while the angular and proportional measurements did not correlate. CONCLUSIONS Comparisons between linear cephalometric measurements obtained with different devices from the same manufacturer showed maximum rates of expansion of 0.6%, 1.25% and 2.3%, respectively, for the devices from Instrumentarium (OP-100, Instrumentarium, Finland), Panoura (10CSU, Yoshida, Japan) and Satelec/Tomeceph (XMind, Satelec/Tomeceph Orion Corporation, Finland).

Analysis of reliability, accuracy, sensitivity and predictive value of a subjective method to classify facial pattern in adults

ABSTRACT Introduction: Craniofacial pattern diagnosis is vital in Orthodontics, as it influences decision-making regarding treatment options and prognosis. Capelozza Filho proposed a subjective method for facial classification comprising five patterns: I, II, III, Long Face and Short Face. Objective: To investigate the accuracy of a subjective classification method of facial patterns applied to adults. Methods: A sample consisting of 52 adults was used for this study. Frontal and lateral view photographs were taken with subjects at rest position, including frontal smile. Lateral cephalometric radiographs were organized in a PowerPoint® presentation and submitted to 20 raters. Method performance was assessed by examining reproducibility with Kappa test and calculating accuracy, sensitivity and positive predictive values, for which 70% was set as critical value. The gold standard of the classification was personally set by the author of the method. Results: Reproducibility was considered moderate (Kappa = 0.501); while accuracy, sensitivity and positive predictive values yielded similar results, but below 70%. Conclusions: The subjective method of facial classification employed in the present study still needs to have its morphological criteria improved in order to be used to discriminate the five facial patterns.