Goknur Bayram

Viscoelastic characteristics of chain extended/branched and linear polyethylene terephthalate resins

Two chemically modified chain extended/branched polyethylene terephthalate (PET) resins and one unmodified resin, considered to be linear, were characterized in terms of their melt flow, die swell, and viscoelastic properties. The three resins had reportedly similar nominal intrinsic viscosities but exhibited different viscoelastic behavior. The modified resins had lower melt flow index, higher die swell, higher complex viscosity and higher storage modulus than the unmodified one. The Cole–Cole plots of the resins were independent of temperature, and the data for modified resins formed a group that lay below the data group for the unmodified PET. The distribution of relaxation times was determined. The modified resins had higher relaxation strength, Gi, especially at high relaxation times, λi. The mean relaxation times of the chain extended/branched resins were approximately an order of magnitude higher than that of the unmodified resin, implying pronounced elastic character. The modified resins had better foaming characteristics in extrusion foam processing than the unmodified one owing to their elastic nature.

Improvement of adhesion between poly(ethylene terephthalate) and polyethylene

Three-layer films were prepared with polyethylene (PE) and poly(ethylene terephthalate) (PET) films as the outer layers and a film of high-density polyethylene (HDPE)/ethylene-methyl acrylate-glycidyl methacrylate (E-MA-GMA) terpolymer blend as the inner layer using compression molding. E-MA-GMA, an elastomer containing an epoxy functional group, was used as the adhesion promoting agent in the multilayer films. The effects of processing temperature, pressure application time and elastomer concentration on adhesion were investigated. The adhesion strength between PE and PET films increased with increasing bonding temperature, bonding time and elastomer concentration. From contact angle measurements, it was observed that the work of adhesion between the polymers increased with increasing amount of elastomer. Improved adhesion between PET and HDPE with 30% elastomer films was confirmed by SEM analyses of the film layers. Using FT-IR analysis of PE/HDPE-30% elastomer/PET delaminated film, the decrease in peak intensity of the epoxy groups tends to indicate reaction of epoxy functionality with functional groups in PET.

Processing and characterization of multilayer films of poly(ethylene terephthalate) and surface-modified poly(tetrafluoroethylene)

Multilayer films were prepared from poly(tetrafluoroethylene) (PTFE) and poly(ethylene terephthalate) (PET) films together with using an adhesion promoting layer (tie-layer) consisting of ethylene-methyl acrylate-glycidyl methacrylate (E-MA-GMA) terpolymer and low density polyethylene (LDPE) blend. Na/naphthalene treatment and subsequent acrylic acid grafting were applied on the surfaces of PTFE for chemical modification. FT-IR spectroscopy, XPS analysis and surface energy measurements were performed to characterize the modified PTFE films. The analyses showed defluorination and oxidation of PTFE surface, and supported the acrylic acid grafting. The surface energy of modified surfaces enhanced with respect to unmodified one, which promoted adhesion. The multilayers were subjected to T-peel tests to measure the adhesion strength between PET and modified PTFE. Peel strength between the films increased with increasing E-MA-GMA amount in the tie-layer. A proportional dependence of peel strength on Na/naphthalene treatment time was observed for multilayers containing acrylic acid grafted or ungrafted PTFE. From SEM analysis, it was observed that the texture of the PTFE surface after modifications became rougher when compared to untreated PTFE. The peeled surfaces were also analyzed by SEM. The micrographs evidence that the energy absorbing mechanism is the plastic deformation of the tie-layer, which is responsible for obtaining high peel strengths.

Processing and Characterization of Short Glass Fiber/ABS/Polyamide-6 Composites

The main objective of this study is to determine the effects of short glass fiber (SGF) content and extrusion conditions such as screw speed and barrel temperature, on the mechanical properties and morphologies of structural composites produced by compounding SGFs with poly (acrylonitrile-butadiene-styrene) (ABS). It was also aimed to determine the effects of adhesion at the fiber/matrix interface, which was promoted by incorporation of polyamide-6 (PA6) to the ABS/SGF composite. Results showed that increasing screw speed during extrusion decreased the average fiber length; therefore mechanical properties of the composites affected negatively. The increasing extrusion temperature decreased the fiber length degradation and higher tensile strength and modulus values were obtained. The use of PA6 in composites increased the interfacial adhesion, which was supported by SEM microphotographs; therefore, improved mechanical properties were obtained.