Heun Park

Stretchable Array of Highly Sensitive Pressure Sensors Consisting of Polyaniline Nanofibers and Au-Coated Polydimethylsiloxane Micropillars

We report on the facile fabrication of a stretchable array of highly sensitive pressure sensors. The proposed pressure sensor consists of the top layer of Au-deposited polydimethylsiloxane (PDMS) micropillars and the bottom layer of conductive polyaniline nanofibers on a polyethylene terephthalate substrate. The sensors are operated by the changes in contact resistance between Au-coated micropillars and polyaniline according to the varying pressure. The fabricated pressure sensor exhibits a sensitivity of 2.0 kPa(-1) in the pressure range below 0.22 kPa, a low detection limit of 15 Pa, a fast response time of 50 ms, and high stability over 10000 cycles of pressure loading/unloading with a low operating voltage of 1.0 V. The sensor is also capable of noninvasively detecting human-pulse waveforms from carotid and radial artery. A 5 × 5 array of the pressure sensors on the deformable substrate, which consists of PDMS islands for sensors and the mixed thin film of PDMS and Ecoflex with embedded liquid metal interconnections, shows stable sensing of pressure under biaxial stretching by 15%. The strain distribution obtained by the finite element method confirms that the maximum strain applied to the pressure sensor in the strain-suppressed region is less than 0.04% under a 15% biaxial strain of the unit module. This work demonstrates the potential application of our proposed stretchable pressure sensor array for wearable and artificial electronic skin devices.

Stretchable Active Matrix Temperature Sensor Array of Polyaniline Nanofibers for Electronic Skin

A stretchable polyaniline nanofiber temperature sensor array with an active matrix consisting of single-walled carbon nanotube thin-film transistors is demonstrated. The integrated temperature sensor array gives mechanical stability under biaxial stretching of 30%, and the resultant spatial temperature mapping does not show any mechanical or electrical degradation.

Stretchable Loudspeaker using Liquid Metal Microchannel

Considering the various applications of wearable and bio-implantable devices, it is desirable to realize stretchable acoustic devices for body-attached applications such as sensing biological signals, hearing aids, and notification of information via sound. In this study, we demonstrate the facile fabrication of a Stretchable Acoustic Device (SAD) using liquid metal coil of Galinstan where the SAD is operated by the electromagnetic interaction between the liquid metal coil and a Neodymium (Nd) magnet. To fabricate a liquid metal coil, Galinstan was injected into a micro-patterned elastomer channel. This fabricated SAD was operated simultaneously as a loudspeaker and a microphone. Measurements of the frequency response confirmed that the SAD was mechanically stable under both 50% uniaxial and 30% biaxial strains. Furthermore, 2000 repetitive applications of a 50% uniaxial strain did not induce any noticeable degradation of the sound pressure. Both voice and the beeping sound of an alarm clock were successfully recorded and played back through our SAD while it was attached to the wrist under repeated deformation. These results demonstrate the high potential of the fabricated SAD using Galinstan voice coil in various research fields including stretchable, wearable, and bio-implantable acoustic devices.

Fabrication of High-Sensitivity Skin-Attachable Temperature Sensors with Bioinspired Microstructured Adhesive

In this study, we demonstrate the fabrication of a highly sensitive flexible temperature sensor with a bioinspired octopus-mimicking adhesive. A resistor-type temperature sensor consisting of a composite of poly(N-isopropylacrylamide) (pNIPAM)-temperature sensitive hydrogel, poly(3,4-ethylenedioxythiophene) polystyrene sulfonate, and carbon nanotubes exhibits a very high thermal sensitivity of 2.6%·°C-1 between 25 and 40 °C so that the change in skin temperature of 0.5 °C can be accurately detected. At the same time, the polydimethylsiloxane adhesive layer of octopus-mimicking rim structure coated with pNIPAM is fabricated through the formation of a single mold by utilizing undercut phenomenon in photolithography. The fabricated sensor shows stable and reproducible detection of skin temperature under repeated attachment/detachment cycles onto skin without any skin irritation for a long time. This work suggests a high potential application of our skin-attachable temperature sensor to wearable devices for medical and health-care monitoring.

Skin-Attachable, Stretchable Electrochemical Sweat Sensor for Glucose and pH Detection

As part of increased efforts to develop wearable healthcare devices for monitoring and managing physiological and metabolic information, stretchable electrochemical sweat sensors have been investigated. In this study, we report on the fabrication of a stretchable and skin-attachable electrochemical sensor for detecting glucose and pH in sweat. A patterned stretchable electrode was fabricated via layer-by-layer deposition of carbon nanotubes (CNTs) on top of patterned Au nanosheets (AuNS) prepared by filtration onto stretchable substrate. For the detection of glucose and pH, CoWO4/CNT and polyaniline/CNT nanocomposites were coated onto the CNT-AuNS electrodes, respectively. A reference electrode was prepared via chlorination of silver nanowires. Encapsulation of the stretchable sensor with sticky silbione led to a skin-attachable sweat sensor. Our sensor showed high performance with sensitivities of 10.89 μA mM-1 cm-2 and 71.44 mV pH-1 for glucose and pH, respectively, with mechanical stability up to 30% stretching and air stability for 10 days. The sensor also showed good adhesion even to wet skin, allowing the detection of glucose and pH in sweat from running while being attached onto the skin. This work suggests the application of our stretchable and skin-attachable electrochemical sensor to health management as a high-performance healthcare wearable device.

Highly Conductive, Stretchable, and Transparent PEDOT:PSS Electrodes Fabricated with Triblock Copolymer Additives and Acid Treatment

Here, we report on a highly conductive, stretchable, and transparent electrode of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) fabricated via modification with triblock copolymer, poly(ethylene glycol)- block-poly(propylene glycol)- block-poly(ethylene glycol) (PEO20-PPO70-PEO20, Pluronic P123), and post-treatment with sulfuric acid. The fabricated electrode exhibits high transparency (89%), high electrical conductivity (∼1700 S/cm), and minimal change in resistance (∼4%) under repetitive stretch-release cycles at 40% tensile strain after stabilization. P123 acts as a secondary dopant and plasticizer, resulting in enhanced electrical conductivity and stretchability of PEDOT:PSS. Furthermore, after sulfuric acid post-treatment, P123 helps the electrode to maintain its stretchability. A successful demonstration of the stretchable interconnection was shown by stretching the P123-modified PEDOT:PSS electrodes, which were connected with light-emitting diodes (LEDs) in series. Finally, a stretchable and transparent touch sensor consisting of our fabricated electrodes and an LED array and stretchable semitransparent supercapacitor were presented, suggesting a great potential of our electrodes in the application to various deformable devices.

Wire-Shaped Supercapacitors with Organic Electrolytes Fabricated via Layer-by-Layer Assembly

A wire-shaped supercapacitor (WSS) has structural advantages of high flexibility and ease of incorporation into conventional textile substrates. In this work, we report a thin reproducible WSS fabricated via layer-by-layer (LbL) assembly of multiwalled carbon nanotubes (MWCNTs), combined with an organic electrolyte of propylene carbonate (PC)-acetonitrile (ACN)-lithium perchlorate (LiClO4)-poly(methyl methacrylate) (PMMA) that extends the voltage window to 1.6 V. The MWCNTs were uniformly deposited on a curved surface of a thin Au wire using an LbL assembly technique, resulting in linearly increased areal capacitance of the fabricated WSS. Vanadium oxide was coated on the LbL-assembled MWCNT electrode to induce pseudocapacitance, hence enhancing the overall capacitance of the fabricated WSS. Both the cyclic stability of the WSS and the viscosity of the electrolyte could be optimized by controlling the mixing ratio of PC to ACN. As a result, the fabricated WSS exhibits an areal capacitance of 5.23 mF cm-2 at 0.2 mA cm-2, an energy density of 1.86 μ W h cm-2, and a power density of 8.5 mW cm-2, in addition to a high cyclic stability with a 94% capacitance retention after 10 000 galvanostatic charge-discharge cycles. This work demonstrates a great potential of the fabricated scalable WSS in the application to high-performance textile electronics as an integrated energy storage device.

Highly Durable and Flexible Transparent Electrode for Flexible Optoelectronic Applications

A highly-durable, highly-flexible transparent electrode (FTE) is developed by applying a composite made of a thin metal grid and a doped conducting polymer onto a colorless polyimide-coated NOA63 substrate. The proposed FTE exhibits a transparency of 90.7% at 550 nm including the substrate and a sheet resistance of 30.3 Ω/sq and can withstand both moderately high-temperature annealing (∼180 °C) and acidic solution (70 °C, pH 0.3) processes without performance degradation. The fabricated FTE yielded good mechanical stability under 10 000 cycles of bending deformations at a bending radius less than 1 mm without degradation of electrical conductivity. The high durability of the proposed FTE allows for the fabrication of flexible energy harvesting devices requiring harsh conditions, such as highly flexible perovskite solar cells (FPSCs) with a steady-state power conversion efficiency (PCE) of 12.7%. Notably, 93% of the original PCE is maintained after 2000 bending cycles at an extremely small bending radius of 1.5 mm. The FPSCs installed on curved surfaces of commercial devices drive them under various environments. The applicability of the proposed FTE is further confirmed via the fabrication of a flexible perovskite light-emitting diode. The proposed FTE demonstrates great potential for applications in the field of flexible optoelectronic devices.