Ismael Cotte-Rodriguez

Direct, trace level detection of explosives on ambient surfaces by desorption electrospray ionization mass spectrometry

Desorption electrospray ionization (DESI) mass spectrometry is used to detect trace amounts of explosives present on a variety of ambient surfaces in 5-second analysis times without any sample preparation.

In Situ Trace Detection of Peroxide Explosives by Desorption Electrospray Ionization and Desorption Atmospheric Pressure Chemical Ionization

Desorption electrospray ionization (DESI) mass spectrometry is used for the rapid (<5 s), selective, and sensitive detection of trace amounts of the peroxide-based explosives, hexamethylene triperoxide diamine (HMTD), tetracetone tetraperoxide (TrATrP), and triacetone triperoxide (TATP), directly from ambient surfaces without any sample preparation. The analytes are observed as the alkali metal ion complexes. Remarkably, collision-induced dissociation (CID) of the HMTD, TATP, and TrATrP complexes with Na(+), K(+), and Li(+) occurs with retention of the metal, a process triggered by an unusual homolytic cleavage of the peroxide bond, forming a distonic ion. This is followed by elimination of a fragment of 30 mass units, shown to be the expected neutral molecule, formaldehyde, in the case of HMTD, but shown by isotopic labeling experiments to be ethane in the cases of TATP and TrATrP. Density functional theory (DFT) calculations support the suggested fragmentation mechanisms for the complexes. Binding energies of Na+ of 40.2 and 33.1 kcal/mol were calculated for TATP-Na(+) and HMTD-Na(+) complexes, suggesting a strong interaction between the peroxide groups and the sodium ion. Increased selectivity is obtained either by MS/MS or by doping the spray solvent with additives that produce the lithium and potassium complexes of TATP, HMTD, and TrATrP. Addition of dopants into the solvent spray increased the signal intensity by an order of magnitude. When pure alcohol or aqueous hydrogen peroxide was used as the spray solvent, the (HMTD + Na)+ complex was able to bind a molecule of alcohol (methanol or ethanol) or hydrogen peroxide, providing additional characteristic ions to increase the selectivity of analysis. DESI also allowed the rapid detection of peroxide explosives in complex matrixes such as diesel fuel and lubricants using single or multiple cation additives (Na(+), K(+), and Li(+), and NH4(+)) in the spray solvent. Low-nanogram detection limits were achieved for HMTD, TrATrP, and TATP in these complex matrixes. The DESI response was linear over 3 orders of magnitude for HMTD and TATP on paper surfaces (1-5000 ng), and quantification of both peroxide explosives from paper gave precisions (RSD) of less than 3%. The use of pure water and compressed air as the DESI spray solution and nebulizing gas, respectively, showed similar ionization efficiencies to those obtained using methanol/water mixtures and nitrogen gas (the typical choices). An alternative ambient method, desorption atmospheric pressure chemical ionization (DAPCI), was also used to detect trace amounts of HMTD and TATP in air by complexation with gas-phase ammonium ions (NH4(+)) generated by atmospheric pressure ammonia ionization.

Non-proximate detection of explosives and chemical warfare agent simulants by desorption electrospray ionization mass spectrometry.

Desorption electrospray ionization (DESI) mass spectrometry is used for the selective and sensitive detection of trace amounts of explosives and chemical warfare agent simulants from ambient surfaces at distances of up to 3 meters from the mass spectrometer.

Rapid trace detection of triacetone triperoxide (TATP) by complexation reactions during desorption electrospray ionization

Desorption electrospray ionization (DESI) mass spectrometry is used for rapid, specific and sensitive detection of trace amounts of the notorious explosive TATP present on ambient surfaces by alkali metal complexation in a simple spray technique.

cis-Diol functional group recognition by reactive desorption electrospray ionization (DESI)

Heterogeneous reactions at a solution/solid interface are utilized in an ambient mass spectrometry experiment to recognize the cis-diol functionality by its selective complexation reaction to form a cyclic boronate.

Improved detection of low vapor pressure compounds in air by serial combination of single-sided membrane introduction with fiber introduction mass spectrometry (SS-MIMS-FIMS)

The use of two methods in tandem, single-sided membrane introduction mass spectrometry (SS-MIMS) and fiber introduction mass spectrometry (FIMS), is presented as a technique for field analysis. The combined SS-MIMS-FIMS technique was employed in both a modified commercial mass spectrometer and a miniature mass spectrometer for the selective preconcentration of the explosive simulant o-nitrotoluene (ONT) and the chemical warfare agent simulant, methyl salicylate (MeS), in air. A home-built FIMS inlet was fabricated to allow introduction of the solid-phase microextraction (SPME) fiber into the mass spectrometer chamber and subsequent desorption of the trapped compounds using resistive heating. The SS-MIMS preconcentration system was also home-built from commercial vacuum parts. Optimization experiments were done separately for each preconcentration system to achieve the best extraction conditions prior to use of the two techniques in combination. Improved limits of detection, in the low ppb range, were observed for the combination compared to FIMS alone, using several SS-MIMS preconcentration cycles. The SS-MIMS-FIMS response for both instruments was found to be linear over the range 50 to 800 ppb. Other parameters studied were absorption time profiles, effects of sample flow rate, desorption temperature, fiber background, memory effects, and membrane fatigue. This simple, sensitive, accurate, robust, selective, and rapid sample preconcentration and introduction technique shows promise for field analysis of low vapor pressure compounds, where analyte concentrations will be extremely low and the compounds are difficult to extract from a matrix like air.

Solid phase micro-extraction in a miniature ion trap mass spectrometer

Fiber introduction mass spectrometry (FIMS), a variation of solid-phase microextraction (SPME) and membrane introduction mass spectrometry (MIMS), is employed with a miniature mass spectrometer. The inlet system, constructed of commercially available vacuum parts, allows the direct introduction of the SPME needle vacuum chamber into the mass spectrometer. Thermal desorption of the analyte from the poly(dimethylsiloxane) (PDMS) coated fiber was achieved with a built in nichrome heater, followed by electron ionization of the analytes internal to the cylindrical ion trap (CIT). The system has been tested with several volatile organic compounds (VOC) in air and to analyze the headspace over aqueous solutions, with limits of detection in the low ppb range. The signal rise (10-90%) and fall (90-10%) times for the system ranged from 0.1 to 1 s (rise) and 1.2 to 6 s (fall) using heated desorption. In addition, this method has been applied to quantitation of toluene in benzene, toluene, xylene (BTX) mixtures in water and gasoline. This simple and rapid analysis method, coupled to a portable mass spectrometer, has been shown to provide a robust, simple, rapid, reproducible, accurate and sensitive (low ppb range) fieldable approach to the effective in situ analysis of VOC in various matrices.

Chemical analysis and chemical imaging of fragrances and volatile compounds by low-temperature plasma ionization mass spectrometry.

RATIONALE The rapid analysis of volatile compounds, such as fragrances, is important in many commercial industries. The various ambient ionization methods have until now been largely applied to non-volatile or low-volatile compounds with success, and this study develops a semi-quantitative method for volatile compounds in commercial cleaning products. METHODS Low-temperature plasma (LTP) ionization was used to perform rapid analysis, determine limits of detection (LODs) and perform chemical imaging on eight fragrances. Several mass analyzers including an ion trap, a quadrupole and an orbitrap were used to rapidly screen volatile compounds from cloth, paper, and glass and determine compositions present in a commercial cleaning product. Peltier cooling was used in some cases to enhance the retention time of compounds on a surface. RESULTS This LTP method allowed the detection of fragrances in low picogram absolute amounts from glass, paper and cloth. Quantitation was demonstrated for compounds in a commercial cleaning product 1 min after the product was applied to a vinyl tile surface. High-throughput analysis and simultaneous detection of multiple compounds in a mixture were demonstrated with analysis times of less than 1 min. Modest spatial resolution (better than 1 cm) was achieved with LTP ionization. CONCLUSIONS A semi-quantitative method has been demonstrated for the routine analysis of volatile and semi-volatile compounds. This method would be useful in quality control and production environments to determine product persistence, location of analytes and to complement olfactory studies for determining concentrations in the ambient environment.

Gas-phase reactions for selective detection of the explosives TNT and RDX.

Highly selective gas-phase reactions with ethyl vinyl ether (EVE) of major electron (EI) and chemical ionization (CI) fragment ions of the explosives TNT and RDX have been uncovered. The fragment ion of m/z 210 from TNT undergoes [4(+)+ 2] cycloaddition with EVE to form an oxo-iminium ion of m/z 282, which dissociates by acetaldehyde loss after a [1,5-H] shift to form a quinolynium ion of m/z 238. The fragment ion of m/z 149 from RDX reacts with EVE by a formal vinylation reaction, that is, the elusive cyclic adduct loses ethanol to yield a nitro-iminium ion of m/z 175, which reacts further with EVE to form a second cyclic product ion of m/z 247. Calculations and MS/MS experiments support the proposed structures. These highly characteristic reactions of diagnostic EI and CI fragment ions improve selectivity for TNT and RDX detection.

Introduction to Protein Mass Spectrometry

Proteins fulfill a plethora of biochemical functions within every living organism, and mass spectrometry (MS) has become one of the most powerful and popular modern physical–chemical methods to study the complexities of proteins. In particular, the invention of matrix-assisted laser desorption/ionization (MALDI) [1] and electrospray ionization (ESI) technologies[2, 3] allows one to measure protein molecular weights and sequences, and to probe conformations and post-translational modifications of proteins. In addition, the mass range of species amenable for MS analysis has increased, enabling the transfer of ionized non-covalent species with masses well over one million (e.g., 1.5 MDa 24-Mer flavoprotein vanillyl-alcohol oxidase (VAO) from Penicillium simplicissimum [4]) into the gas phase. These advances moved MS into the range of intact protein oligomers and functional machineries.