J. M. Baptista

Light requirements in microalgal photobioreactors: an overview of biophotonic aspects

In order to enhance microalgal growth in photobioreactors (PBRs), light requirement is one of the most important parameters to be addressed; light should indeed be provided at the appropriate intensity, duration, and wavelength. Excessive intensity may lead to photo-oxidation and -inhibition, whereas low light levels will become growth-limiting. The constraint of light saturation may be overcome via either of two approaches: increasing photosynthetic efficiency by genetic engineering, aimed at changing the chlorophyll antenna size; or increasing flux tolerance, via tailoring the photonic spectrum, coupled with its intensity and temporal characteristics. These approaches will allow an increased control over the illumination features, leading to maximization of microalgal biomass and metabolite productivity. This minireview briefly introduces the nature of light, and describes its harvesting and transformation by microalgae, as well as its metabolic effects under excessively low or high supply. Optimization of the photosynthetic efficiency is discussed under the two approaches referred to above; the selection of light sources, coupled with recent improvements in light handling by PBRs, are chronologically reviewed and critically compared.

Recent Advances in High-Birefringence Fiber Loop Mirror Sensors

Recent advances in devices and applications of high-birefringence fiber loop mirror sensors are addressed. In optical sensing, these devices may be used as strain and temperature sensors, in a separate or in a simultaneous measurement. Other described applications include: refractive index measurement, optical filters for interrogate gratings structures and chemical etching control. The paper analyses and compares different types of high-birefringence fiber loop mirror sensors using conventional and microstructured optical fibers. Some configurations are presented for simultaneous measurement of physical parameters when combined with others optical devices, for example with a long period grating.

Simultaneous Measurement for Strain and Temperature Based on a Long-Period Grating Combined With a High-Birefringence Fiber Loop Mirror

This work presents an alternative solution for simultaneous measurement of strain and temperature. The sensing head is formed by a long-period fiber grating combined with a high-birefringence fiber loop mirror resulting in a configuration capable of temperature and strain discrimination. These optical devices have opposite sensitivity responses when a variation of temperature and/or strain is applied. Maximum errors of plusmn0.8degC and plusmn21muepsiv are reported over 60 degC and 700-muepsiv measurement ranges, respectively

Temperature-Independent Strain Sensor Based on a Hi-Bi Photonic Crystal Fiber Loop Mirror

This work presents an optical sensor based on a highly birefringent photonic crystal fiber (Hi-Bi PCF) loop mirror. The length of the sensing head is 380 mm and its corresponding wavelength spacing between two interferometer minima is 8 nm. The optical sensor was characterized in strain and in temperature with an uncoated Hi-Bi PCF and with an acrylate coated Hi-Bi PCF. Different results for strain and temperature sensitivity were obtained. Relatively to the strain measurement, the sensor with the uncoated Hi-Bi PCF presents slightly less sensitivity (1.11 ) when compared with coated Hi-Bi PCF (1.21 ). For the temperature measurement and with the uncoated Hi-Bi PCF, the optical sensor is insensitive to temperature (0.29 pm/K).

Curvature sensor using a highly birefringent photonic crystal fiber with two asymmetric hole regions in a Sagnac interferometer

A curvature sensor based on a highly birefringent (Hi-Bi) photonic crystal fiber inserted into a Sagnac interferometer is demonstrated. For this purpose, a novel Hi-Bi photonic crystal fiber was designed and fabricated. Half of the microstructured region of the photonic crystal fiber was composed by large diameter holes, while the other half contained small diameter holes. Because of this geometry, the fiber core was shifted from the center and high birefringence appears in the optical fiber. Curvature was applied for three different fiber directions for a range of 0.6-5 m(-1). Temperature and longitudinal strain was also characterized for constant curvature. The configuration showed insensitivity to these two physical parameters.

Simultaneous measurement of multiparameters using a Sagnac interferometer with polarization maintaining side-hole fiber

A Sagnac interferometer with a section of a polarization maintaining side-hole fiber for multiparameter measurement is proposed. The sensor was experimentally demonstrated to be sensitive to torsion, temperature, and longitudinal strain, simultaneously. The birefringence in the investigated side-hole fiber is induced simultaneously by the elliptical shape of a germanium-doped core and by field overlap with the air holes surrounding the core. The latter effect is purely geometrical and causes high chromatic dispersion of the group birefringence in the long wavelength range, which results in a different period of spectral interference fringes. A different wavelength response is obtained for each interference fringe peak when the fiber is subjected to torsion, temperature, or longitudinal strain. A matrix equation for simultaneous measurement of the three parameters--torsion, temperature, and longitudinal strain--is also proposed.

Fiber-Optic Interferometric Torsion Sensor Based on a Two-LP-Mode Operation in Birefringent Fiber

A fiber-optic sensor for torsion measurement, based on a two-linearly polarized (LP)-mode operation in ultrahigh birefringent photonic crystal fiber is described. The structure of the photonic crystal fiber presents two large asymmetric holes adjacent to the core fiber. When linearly polarized light is injected in x - and y -directions, respectively, two separate interferometers can be obtained. In one of these cases, as torsion is applied to the sensing head a beat between the two interferometers is formed due to the simultaneous excitation of the two polarization states. The detection technique to read the torsion sensor is based on the analysis of the fast Fourier transform, which proved to be an effective and simple solution. The sensor exhibited reduced sensitivity to temperature.

All Fiber Mach–Zehnder Interferometer Based on Suspended Twin-Core Fiber

An all fiber Mach-Zehnder interferometer using suspended twin-core fiber is described. Due to the birefringence of the fiber cores, two interferometers are obtained when the fiber is illuminated by a polarized light. Applying curvature or temperature to the sensing head, different sensitivities are observed. In order to discriminate curvature from temperature in the suspended twin-core fiber Mach-Zehnder sensor, the matrix method is used.

Temperature-Independent Curvature Sensor Using FBG Cladding Modes Based on a Core Misaligned Splice

A fiber-optic curvature sensor based on a core offset single-mode fiber (SMF) combined with a fiber Bragg grating (FBG) is presented. The FBG cladding modes are efficiently excited by the large core misalignment. The curvature of the fiber can be obtained by the ratio between the recoupled cladding mode power and the reflected core mode power. These measurements are independent from temperature variation.

Optical refractometer based on a birefringent Bragg grating written in an H-shaped fiber

An optical refractometer based on a birefringent (Hi-Bi) fiber Bragg grating (FBG) written in a new H-shaped fiber structure is proposed. This structure is formed by opening the two holes of a side-hole fiber using chemical etching. When the Hi-Bi FBG is immersed in different liquids, different responses of the slow and fast wavelengths are obtained. The refractometer is also capable of simultaneous measurement of refractive index and temperature.