James Kingsley

Carbazole and thienyl benzo[1,2,5]thiadiazole based polymers with improved open circuit voltages and processability for application in solar cells

The preparation of low energy gap carbazole based main-chain polymers having improved open circuit voltages (Voc) and solubility is described. Poly[9-(heptadecan-9-yl)-9H-carbazole-2,7-diyl-alt-(5,6-bis(octyloxy)-4,7-di(thiophen-2-yl)benzo[c][1,2,5]thiadiazole)-5,5-diyl] P1 and poly[9-(heptadecan-9-yl)-9H-carbazole-2,7-diyl-alt-(5,6-bis(octyloxy)-4,7-di(2,2′-bithiophen-5-yl)benzo[c][1,2,5]thiadiazole)-5,5-diyl] P2 were prepared in good yields using Suzuki coupling methodologies. The polymers were characterized by NMR spectroscopy; UV-Vis absorption spectroscopy, cyclic voltammetry and their molecular weights were estimated using gel permeation chromatography. Introduction of octyloxy substituents on the benzothiadiazole acceptor repeat units on polymers P1 and P2 enhances their solubility compared to the polymer PCDTBT and alters their electronic and photophysical properties. Investigation of the photovoltaic properties of the two new polymers side by side with those of PCDTBT in bulk heterojunction cells using PC70BM as a molecular acceptor indicated that both polymers provide higher Voc values than that of PCDTBT (0.96 and 0.90 V for P1 and P2 respectively vs. 0.82 V for PCDTBT) and good power conversion efficiencies with PCE values of 4.22 and 4.12% respectively for P1 and P2 and a PCE of 4.30% for PCDTBT.

Selenophene vs. thiophene in benzothiadiazole-based low energy gap donor–acceptor polymers for photovoltaic applications

A series of low energy gap polymers comprising 2,7-linked carbazole or fluorene units flanked by thiophene or selenophene repeat units as alternating donor units and benzothiadiazole with or without alkoxy substituents as alternating acceptor repeat units is reported. The effects of replacing thiophene with selenophene in this series of polymers on their optical, electrochemical and photovoltaic device performance when fabricated into bulk heterojunction solar cells using PC70BM as an acceptor are investigated. Power conversion efficiencies (PCEs) ranging from 3.34 to 5.41% are obtained with these systems. Thiophene-based polymers are found to have higher efficiency compared to comparable selenophene-based polymers. We tentatively explain such differences on the basis of reduced molar absorbance and reduced charge-carrier mobility in the selenophene-based polymers.

Molecular weight dependent vertical composition profiles of PCDTBT:PC71BM blends for organic photovoltaics

We have used Soxhlet solvent purification to fractionate a broad molecular weight distribution of the polycarbazole polymer PCDTBT into three lower polydispersity molecular weight fractions. Organic photovoltaic devices were made using a blend of the fullerene acceptor PC71BM with the molecular weight fractions. An average power conversion efficiency of 5.89% (peak efficiency of 6.15%) was measured for PCDTBT blend devices with a number average molecular weight of Mn = 25.5 kDa. There was significant variation between the molecular weight fractions with low (Mn = 15.0 kDa) and high (Mn = 34.9 kDa) fractions producing devices with average efficiencies of 5.02% and 3.70% respectively. Neutron reflectivity measurements on these polymer:PC71BM blend layers showed that larger molecular weights leads to an increase in the polymer enrichment layer thickness at the anode interface, this improves efficiency up to a limiting point where the polymer solubility causes a reduction of the PCDTBT concentration in the active layer.

Phenylenevinylene Block Copolymers via Ring-Opening Metathesis Polymerization

Fully conjugated block copolymers containing 1,4- and 1,3-phenylenevinylene repeating units can be prepared by the sequential ring opening metathesis polymerization of strained cyclophanedienes, initiated by ruthenium carbene complexes (Grubbs metathesis catalysts). The molecular weight of the constituent blocks can be tightly controlled by changing the catalyst to monomer ratio and the volume fraction of the block copolymers independently tailored by the ratio of the monomers employed. Extensive phase separation between the constituent blocks is observed in thin films of these polymers by atomic force microscopy and efficient energy transfer between blocks containing 1,4- and 1,3-phenylenevinylene units can be seen in the photoluminescence of these materials.

Optical nanolithography using a scanning near-field probe with an integrated light source

An ultracompact near-field optical probe is described that is based on a single, integrated assembly consisting of a gallium nitride (GaN) light-emitting diode (LED), a microlens, and a cantilever assembly containing a hollow pyramidal probe with a subwavelength aperture at its apex. The LED emits ultraviolet light and may be used as a light source for near-field photolithographic exposure. Using this simple device compatible with many commercial atomic force microscope systems, it is possible to form nanostructures in photoresist with a resolution of 35 nm, corresponding to λ/10.

PCDTBT based solar cells: one year of operation under real-world conditions.

We present measurements of the outdoor stability of PCDTBT:PC71BM based bulk heterojunction organic solar cells for over the course of a year. We find that the devices undergo a burn-in process lasting 450 hours followed by a TS80 lifetime of up to 6200 hours. We conclude that in the most stable devices, the observed TS80 lifetime is limited by thermally-induced stress between the device layers, as well as materials degradation as a result of edge-ingress of water or moisture through the encapsulation.

Air processed organic photovoltaic devices incorporating a MoOx anode buffer layer

Molybdenum oxide (MoOx) has been shown to act as an efficient hole extraction layer in organic photovoltaic (OPV) devices. However, exposing MoOx films to air is problematic as it is hygroscopic; the uptake of moisture having a negative impact on its electronic properties. Here, we use spectroscopic ellipsometry to characterise the uptake of water, and fabricate PCDTBT:PC70BM based OPVs to determine its effects on device performance. We then show that thermally annealing MoOx reduces its hygroscopicity, permitting it to be processed in air. Using this process, we create air-processsed OPVs having PCEs (power conversion efficiencies) of up to 5.36%.

The role of the hole-extraction layer in determining the operational stability of a polycarbazole:fullerene bulk-heterojunction photovoltaic device

We have made a comparative study of the relative operational stability of bulk-heterojunction organic photovoltaic (OPV) devices utilising different hole transport layers (HTLs). OPV devices were fabricated based on a blend of the polymer PCDTBT with the fullerene PC70BM, and incorporated the different HTL materials PEDOT:PSS, MoOx and V2O5. Following 620 h of irradiation by light from a solar simulator, we find that devices using the PEDOT:PSS HTL retained the highest efficiency, having a projected T80 lifetime of 14 500 h.

Fluorene-based co-polymer with high hole mobility and device performance in bulk heterojunction organic solar cells.

A new donor-acceptor polymer based on 9,9-dioctylfluorene is synthesized and tested in organic photovoltaic devices. Results show that the polymer exhibits good solubility in a range of organic solvents and has a high hole mobility. When blended with a PC70 BM acceptor and fabricated into a bulk heterojunction, photovoltaic devices having a maximum power conversion efficiency (PCE) of 6.2% and a peak external quantum efficiency of 74% are created. Such efficiencies are realized without any necessity for solvent additives or thermal annealing protocols.

Dependence on material choice of degradation of organic solar cells following exposure to humid air.

ABSTRACT Electron microscopy has been used to study the degradation of organic solar cells when exposed to humid air. Devices with various different combinations of commonly used organic solar cell hole transport layers and cathode materials have been investigated. In this way the ingress of water and the effect it has on devices could be studied. It was found that calcium and aluminum in the cathode both react with water, causing voids and delamination within the device. The use of poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) was found to increase the degradation by easing water ingress into the device. Replacing these materials removed these degradation features.