Jiahao Chen

Limits to the Effect of Substrate Roughness or Smoothness on the Odd–Even Effect in Wetting Properties of n-Alkanethiolate Monolayers

This study investigates the effect of roughness on interfacial properties of an n-alkanethiolate self-assembled monolayer (SAM) and uses hydrophobicity to demonstrate the existence of upper and lower limits. This article also sheds light on the origin of the previously unexplained gradual increase in contact angles with increases in the size of the molecule making the SAM. We prepared Au surfaces with a root-mean-square (RMS) roughness of ∼0.2-0.5 nm and compared the wetting properties of n-alkanethiolate (C10-C16) SAMs fabricated on these surfaces. Static contact angles, θ(s), formed between the SAM and water, diethylene glycol, and hexadecane showed an odd-even effect irrespective of the solvent properties. The average differences in subsequent SAM(E) and SAM(O) are Δθ(s|n  – (n+1)|) ≈ 1.7° (n = even) and Δθ(s|n – (n+1)|) ≈ 3.1° (n = odd). A gradual increase in θ(s) with increasing length of the molecule was observed, with values ranging from water 104.7-110.7° (overall Δθ(s) = 6.0° while for the evens Δθ(s)(E) = 4.4° and odds Δθ(s)(O) = 3.5°) to diethylene glycol 72.9-80.4° (overall Δθ(s) = 7.5° while for the evens Δθ(s)(E) = 2.9° and odds Δθ(s)(O) = 2.4°) and hexadecane 40.4–49.4° (overall Δθ(s) = 9.0° while for the evens Δθ(s)(E) = 3.7° and odds Δθ(s)(O) = 2.1°). This article establishes that the gradual increase in θ(s) with increasing molecular size in SAMs is due to asymmetry in the zigzag oscillation in the odd-even effect. Comparison of the magnitude and proportion differences in this asymmetry allows us to establish the reduction in interfacial dispersive forces, due to increasing SAM crystallinity with increasing molecular size, as the origin of this asymmetry. By comparing the dependence of θ(s) on surface roughness we infer that (i) RMS roughness ≈ 1 nm is a theoretical limit beyond which the odd-even effect cannot be observed and (ii) on a hypothetically flat surface the maximum difference in hydrophobicity, as expressed in θ(s), is ∼3°.

Mechanical Fracturing of Core-Shell Undercooled Metal Particles for Heat-Free Soldering.

Phase-change materials, such as meta-stable undercooled (supercooled) liquids, have been widely recognized as a suitable route for complex fabrication and engineering. Despite comprehensive studies on the undercooling phenomenon, little progress has been made in the use of undercooled metals, primarily due to low yields and poor stability. This paper reports the use of an extension of droplet emulsion technique (SLICE) to produce undercooled core-shell particles of structure; metal/oxide shell-acetate (‘/’ = physisorbed, ‘-’ = chemisorbed), from molten Field’s metal (Bi-In-Sn) and Bi-Sn alloys. These particles exhibit stability against solidification at ambient conditions. Besides synthesis, we report the use of these undercooled metal, liquid core-shell, particles for heat free joining and manufacturing at ambient conditions. Our approach incorporates gentle etching and/or fracturing of outer oxide-acetate layers through mechanical stressing or shearing, thus initiating a cascade entailing fluid flow with concomitant deformation, combination/alloying, shaping, and solidification. This simple and low cost technique for soldering and fabrication enables formation of complex shapes and joining at the meso- and micro-scale at ambient conditions without heat or electricity.

Empirical Evidence for Roughness-Dependent Limit in Observation of Odd–Even Effect in Wetting Properties of Polar Liquids on n-Alkanethiolate Self-Assembled Monolayers

Substrate roughness influences the wetting properties of self-assembled monolayers (SAMs), but details on this dependency at the sub-nanometer level are still lacking. This study investigates the effect of surface roughness on interfacial properties of n-alkanethiolate SAMs, specifically wetting, and confirms the predicted limit to the observation of the odd-even effect in hydrophobicity. This article studies static contact angles of polar and nonpolar probe liquids on a series of n-alkanethiolate SAMs on surfaces with tunable roughness. We prepared Ag surfaces with root-mean-square roughness (Rrms) of ∼0.6-2.2 nm and compared the wetting properties of n-alkanethiolate SAMs fabricated on these surfaces. We measured the static contact angles, θs, formed between SAM and probe liquids [water, glycerol, and hexadecane]. Hexadecane showed an odd-even effect on all surfaces irrespective of the degree of roughness. Polar liquids (water and glycerol), however, showed a dependency on the roughness of the substrate with an odd-even effect observable only on smooth, but not rougher (Rrms ≥ 1.15 nm), surfaces. These results confirm that the previously predicted limit to observation of the odd-even effect in hydrophobicity (here extended to polar liquids) is real. From the results with glycerol, we infer that this limit is not limited just to hydrophobicity but may extend to other polar liquids. Results from hexadecane, however, suggest that this limit may not be a universal property of the SAM.

Revealing the Nature of Molecule–Electrode Contact in Tunneling Junctions Using Raw Data Heat Maps

Mechanistic understanding of charge transport through molecular tunnel junctions requires reproducible and statistically relevant data sets. This challenge has been overcome by development of large area junctions, especially those based on liquid-metal physi-sorbed top-electrodes, such as eutectic gallium-indium. A challenge with these junctions, however, is an inability to diagnose the quality of contact between the top-electrode and the SAMs. Since tunneling currents are dependent on the distance between the two electrodes, we demonstrate that by analyzing all raw unfitted data derived from a measurement using heat-maps, one can deduce the quality of contact and other minor bias-dependent fluctuations in the charge transport behavior. We demonstrate that the use of 3D plots would be challenging to interpret, but adoption of heat maps clearly captures details on junction quality irrespective of the total size of the data set or molecules used. We propose representation of raw data, rather than reliance on statistics, as proof of quality junctions.

Properties of Self-Assembled Monolayers Revealed via Inverse Tensiometry

Self-assembled monolayers (SAMs) have emerged as a simple platform technology and hence have been broadly studied. With advances in state-of-the-art fabrication and characterization methods, new insights into SAM structure and related properties have been delineated, albeit with some discrepancies and/or incoherencies. Some discrepancies, especially between experimental and theoretical work, are in part due to the misunderstanding of subtle structural features such as phase evolution and SAM quality. Recent work has, however, shown that simple techniques, such as the measurement of static contact angles, can be used to delineate otherwise complex properties of the SAM, especially when complemented by other more advanced techniques. In this article, we highlight the effect of nanoscale substrate asperities and molecular chain length on the SAM structure and associated properties. First, surfaces with tunable roughness are prepared on both Au and Ag, and their corresponding n-alkanethiolate SAMs are characterized through wetting and spectroscopy. From these data, chain-length- and substrate-morphology-dependent limits to the odd-even effect (structure and properties vary with the number of carbons in the molecules and the nature of the substrate), parametrization of gauche defect densities, and structural phase evolution (liquidlike, waxy, crystalline interfaces) are deduced. An evaluation of the correlation between the effect of roughness and the components of surface tension (polar-γp and dispersive-γd) reveals that wetting, at nanoscale rough surfaces, evolves proportionally with the ratio of the two components of surface tension. The evolution of conformational order is captured over a range of molecular lengths and parametrized through a dimensionless number, χc. By deploying a well-known tensiometry technique (herein the liquid is used to characterize the solid, hence the term inverse tensiometry) to characterize SAMs, we demonstrate that complex molecular-level phenomena in SAMs can be understood through simplicity.

Quantifying Gauche Defects and Phase Evolution in Self-Assembled Monolayers through Sessile Drops

Self-assembled monolayers (SAMs) are widely used in surface modifications, specifically in tuning the surface chemistry of materials. The structure and properties of SAMs have been extensively studied often with sophisticated tools, even for the simplest n-alkanethiolate SAMs. In SAMs, especially in linear n-alkanethiolates, the properties are dependent on the chain length, which is best manifested in the so-called odd–even effect, a simple yet not fully understood phenomenon. One main challenge is fully delineating the origin of length-dependent properties, which can be due to the structure (ideal SAMs), defect evolution, or substrate-molecule effects. This study demonstrates that utilizing the wetting behavior of polar (water) and nonpolar (hexadecane (HD)) solvents on n-alkanethiolate SAMs formed on ultraflat gold and silver surfaces, the evolution of chain-length-dependent gauche defects can be revealed and parameterized through a newly defined dimensionless number (χ). The observation of the odd–even effect in hydrophobicity, however, depends on the thiol chain length, and it was only observed on longer-chain (>C8) molecules. The trend in this odd–even effect demonstrates that there are three main transitions in the nature of wetting, hence structure, across n-alkanethiols. From wetting with HD, the role of dispersive components in wetting reveal that the SAMs are dynamic, which we attribute to rotations associated with previously reported evolution in gauche defects and changes in packing density. Therefore, from re-expression of the Young–Dupre equation, we define a new dimensionless number associated with molecular conformations, whose periodicity mirrors the energetics of Goodman’s conformations of n-alkanes in unbound states and associated four- or two-twist turns. Therefore, we infer that the evolution in surface energy is largely due to molecular conformations and associated relaxations of the bound thiolates.

Recruiting physisorbed water in surface polymerization for bio-inspired materials of tunable hydrophobicity

Chemical grafting has been widely used to modify the surface properties of materials, especially surface energy for controlled wetting, because of the resilience of such coatings/modifications. Reagents with multiple reactive sites have been used with the expectation that a monolayer will form. The step-growth polymerization mechanism, however, suggests the possibility of gel formation for hydrolyzable moieties in the presence of physisorbed water. In this report, we demonstrated that using alkyltrichlorosilanes (trivalent [i.e., 3 reactive sites]) in the surface modification of a cellulosic material (paper) does not yield a monolayer but rather gives surface-bound particles. We infer that the presence of physisorbed (surface-bound) water allows for polymerization (or oligomerization) of the silane prior to its attachment on the surface. Surface energy mismatch between the hydrophobic tails of the growing polymer and any unreacted bound water leads to the assembly of the polymerizing material into spherical particles to minimize surface tension. By varying paper grammage (16.2–201.4 g m−2), we varied the accessible surface area and thus the amount of surface-adsorbed water, allowing us to control the ratio of the silane to the bound water. Using this approach, polymeric particles were formed on the surface of cellulose fibers ranging from ∼70 nm to a film. The hydrophobicity of the surface, as determined by water contact angles, correlates with particle sizes (p < 0.001, Students t-test), and, hence, the hydrophobicity can be tuned (contact angle between 94° and 149°). Using a model structure of a house, we demonstrated that as a result of this modification, paper-based houses can be rendered self-cleaning or tolerant to surface running water. In another application, we demonstrated that the felicitous choice of architectural design allows for the hydrophobic paper to be used for water harvesting.

Surface polymerization of perfluorosilane treatments on paper mitigates HF production upon incineration

Hydrophobic paper has inspired advances in low-cost technologies. Of importance is the use of perfluorinated reagents, due to suspected release of HF. Surprisingly, by using a coupled TGA-IR-MS, we demonstrate that polymerization of a perfluorinated silane on paper, leads to rapid degradation, low-ash residue, and no toxic HF gas is produced under thermolysis.

Paper-based microfluidic devices by asymmetric calendaring

We report a simple, efficient, one-step, affordable method to produce open-channel paper-based microfluidic channels. One surface of a sheet of paper is selectively calendared, with concomitant hydrophobization, to create the microfluidic channel. Our method involves asymmetric mechanical modification of a paper surface using a rolling ball (ball-point pen) under a controlled amount of applied stress (σz) to ascertain that only one side is modified. A lubricating solvent (hexane) aids in the selective deformation. The lubricant also serves as a carrier for a perfluoroalkyl trichlorosilane allowing the channel to be made hydrophobic as it is formed. For brevity and clarity, we abbreviated this method as TACH (Targeted Asymmetric Calendaring and Hydrophobization). We demonstrate that TACH can be used to reliably produce channels of variable widths (size of the ball) and depths (number of passes), without affecting the nonworking surface of the paper. Using tomography, we demonstrate that these channels can vary from 10s to 100s of microns in diameter. The created hydrophobic barrier extends around the channel through wicking to ensure no leakages. We demonstrate, through modeling and fabrication, that flow properties of the resulting channels are analogous to conventional devices and are tunable based on associated dimensionless numbers.

Mechanically triggered composite stiffness tuning through thermodynamic relaxation (ST3R)

Recent developments in smart responsive composites have utilized various stimuli including heat, light, solvents, electricity, and magnetic fields to induce a change in material properties. Here, we report a thermodynamically driven mechanically responsive composite, exploiting irreversible phase-transformation (relaxation) of metastable undercooled liquid metal core shell particle fillers. Thermal and mechanical analysis reveals that as the composite is deformed, the particles transform from individual liquid droplets to a solid metal network, resulting in a 300% increase in Youngs modulus. In contrast to previous phase change materials, this dramatic change in stiffness occurs autonomously under deformation, is insensitive to environmental conditions, and does not require external energy sources such as heat, light, or electricity. We demonstrate the utility of this approach by transforming a flat, flexible composite strip into a rigid, 3D structure that is capable of supporting 50× its own weight. The ability for shape change and reconfiguration are further highlighted, indicating potential for multiple pathways to trigger or tune composite stiffness.