Jiao Chunmei

Investigation of oxygen vacancy and interstitial oxygen defects in ZnO films by photoluminescence and x-ray photoelectron spectroscopy

ZnO films prepared at different temperatures and annealed at 900 degrees C in oxygen are studied by photoluminescence (PL) and x-ray photoelection spectroscopy (XPS). It is observed that in the PL of the as-grown films the green luminescence (GL) and the yellow luminescence (YL) are related, and after annealing the GL is restrained and the YL is enhanced. The O 1s XPS results also show the coexistence of oxygen vacancy (Vo) and interstitial oxygen (O-i) before annealing and the quenching of the V-o after annealing. By combining the two results it is deduced that the GL and YL are related to the V-o and O-i defects, respectively.

Effect of Nitridation on Morphology, Structural Properties and Stress of AIN Films

We investigate effects of nitridation on AIN morphology, structural properties and stress. It is found that 3 min nitridation can prominently improve AIN crystal structure, and slightly smooth the surface morphology. However, 10 min nitridation degrades out-of-plane crystal structure and surface morphology instead. Additionally, 3-min nitridation introduces more tensile stress (1.5 GPa) in AIN films, which can be attributed to the weaker islands 2D coalescent. Nitridation for 10 min can introduce more defects, or even forms polycrystallinity interlayer, which relaxes the stress. Thus, the stress in AIN with 10 min nitridation decreases to -0.2 GPa compressive stress.

The Growth of Semi-Polar ZnO (101̄1) on Si (111) Substrates Using a Methanol Oxidant by Metalorganic Chemical Vapor Deposition

Semi-polar ZnO (1011) epitaxial films are demonstrated using a methanol oxidant by metalorganic chemical vapor deposition on Si (111) substrates at 500°C. X-ray scanning indicates that there are six kinds of in-plane domain growths, with the ZnO [1012] parallel to the Si (112) direction families. The crystallographic orientation of ZnO is supposed to be caused by surface passivation. The methanol, as a polar molecule, may be adsorbed on the Si (111) surface to form a passivation layer, which inhibits the (0001) ZnO plane deposition on the substrate surface, and as a result the ZnO (1011) plane becomes preferred. The optical properties, examined by a room-temperature photoluminescence spectrum, exhibit a strong near-band-edge emission peak at 379 nm, indicating that the (1011) ZnO film has good crystal quality. These results are significant for research into and for the applications of semi-polar ZnO films.

Influence of Different Interlayers on Growth Mode and Properties of InN by MOVPE

We grow InN epilayers on different interlayers by metal organic vapour phase epitaxy (MOVPE) method, and investigate the effect of interlayer on the properties and growth mode of InN films. Three InN samples were deposited on nitrided sapphire, low-temperature InN (LT-InN) and high-temperature GaN (HT-GaN), respectively. The InN layer grown directly on nitrided sapphire owns the narrowest x-ray diffraction rocking curve (XRC) width of 300 arcsec among the three samples, and demonstrates a two-dimensional (2D) step-flow-like lateral growth mode, which is much different from the three-dimensional (3D) pillar-like growth mode of LT-InN and HT-GaN buffered samples. It seems that mismatch tensile strain is helpful for the lateral epitaxy of InN film, whereas compressive strain promotes the vertical growth of InN films.

A simple route of morphology control and structural and optical properties of ZnO grown by metal-organic chemical vapour deposition

Employing the metal-organic chemical vapour deposition (MOCVD) technique, we prepare ZnO samples with different morphologies from the film to nanorods through conveniently changing the bubbled diethylzinc flux (BDF) and the carrier gas flux of oxygen (OCGF). The scanning electron microscope images indicate that small BDF and OCGF induce two-dimensional growth while the large ones avail quasi-one-dimensional growth. X-ray diffraction (XRD) and Raman scattering analyses show that all of the morphology-dependent ZnO samples are of high crystal quality with a c-axis orientation. From the precise shifts of the 2 theta. locations of ZnO (002) face in the XRD patterns and the E-2(high) locations in the Raman spectra, we deduce that the compressive stress forms in the ZnO samples and is strengthened with the increasing BDF and OCGF. Photoluminescence spectroscopy results show all the samples have a sharp ultraviolet luminescent band without any defects-related emission. Upon the experiments a possible growth mechanism is proposed.

A Comparison between AlN Films Grown by MOCVD Using Dimethylethylamine Alane and Trimethylaluminium as the Aluminium Precursors

Aluminium nitride (AlN) films grown with dimethylethylamine alane (DMEAA) are compared with the ones grown with trimethylaluminium (TMA). In the high-resolution x-ray diffraction Ω scans, the full width at half maximum (FWHM) of (0002) AlN films grown with DMEAA is about 0.70 deg, while the FWHM of (0002) AlN films grown with TMA is only 0.11 deg. The surface morphologies of the films are different, and the rms roughnesses of the surface are approximately identical. The rms roughness of AlN films grown with DMEAA is 47.4 nm, and grown with TMA is 69.4 nm. Although using DMEAA as the aluminium precursor cannot improve the AlN crystal quality, AlN growth can be reached at low temperature of 673 K. Thus, DMEAA is an alternative aluminium precursor to deposit AlN film at low growth temperatures.