Jochen Walser

Region Specific Response of Intervertebral Disc Cells to Complex Dynamic Loading: An Organ Culture Study Using a Dynamic Torsion-Compression Bioreactor

The spine is routinely subjected to repetitive complex loading consisting of axial compression, torsion, flexion and extension. Mechanical loading is one of the important causes of spinal diseases, including disc herniation and disc degeneration. It is known that static and dynamic compression can lead to progressive disc degeneration, but little is known about the mechanobiology of the disc subjected to combined dynamic compression and torsion. Therefore, the purpose of this study was to compare the mechanobiology of the intervertebral disc when subjected to combined dynamic compression and axial torsion or pure dynamic compression or axial torsion using organ culture. We applied four different loading modalities [1. control: no loading (NL), 2. cyclic compression (CC), 3. cyclic torsion (CT), and 4. combined cyclic compression and torsion (CCT)] on bovine caudal disc explants using our custom made dynamic loading bioreactor for disc organ culture. Loads were applied for 8 h/day and continued for 14 days, all at a physiological magnitude and frequency. Our results provided strong evidence that complex loading induced a stronger degree of disc degeneration compared to one degree of freedom loading. In the CCT group, less than 10% nucleus pulposus (NP) cells survived the 14 days of loading, while cell viabilities were maintained above 70% in the NP of all the other three groups and in the annulus fibrosus (AF) of all the groups. Gene expression analysis revealed a strong up-regulation in matrix genes and matrix remodeling genes in the AF of the CCT group. Cell apoptotic activity and glycosaminoglycan content were also quantified but there were no statistically significant differences found. Cell morphology in the NP of the CCT was changed, as shown by histological evaluation. Our results stress the importance of complex loading on the initiation and progression of disc degeneration.

Oriented nanofibrous membranes for tissue engineering applications: Electrospinning with secondary field control

Electrospinning is an electrical field driven method to produce polymer fibre membranes by deposition of a charged polymer jet onto a grounded collector. Fibre alignment within these mats is usually achieved by a fast collector movement, which is not feasible for all collector geometries, such as small diameter tubes or free-form moulds. The aim of this study was to evaluate the use of charged deflector plates to apply a dynamic, alternating electrical field perpendicular to the spinning direction, in order to directly control the fibre trajectory. Different field signal types, deflector plate voltages and deflection frequency ranges have been investigated. 210 poly(ɛ)caprolactone (PCL) membranes were electrospun. SEM images of each membrane were analysed using ImageJ. Main fibre diameter and orientation, as well as the degree of fibre alignment, were calculated, while a subset of the spun scaffolds were tested for their tensile properties. Higher deflector plate voltage amplitude resulted in a better fibre alignment. The best alignment was observed in a low deflection frequency range from 2 to 10 Hz. Mean main fibre direction was 87±18°, relative to the deflection axis, while fibre alignment had only a minor effect on the average fibre diameter. Youngs modulus and yield stress increased with the ratio of the parallel fibre component. The feasibility of the described method to achieve fibre alignment was demonstrated. However, the main fibre direction is not aligned with the deflection axis, but consistently perpendicular to it, which is also reflected in the tensile properties of spun samples.

Direct electrospinning of 3D auricle-shaped scaffolds for tissue engineering applications

Thirty-two poly(ε)caprolactone (PCL) scaffolds have been produced by electrospinning directly into an auricle-shaped mould and seeded with articular chondrocytes harvested from bovine ankle joints. After seeding, the auricle shaped constructs were cultured in vitro and analysed at days 1, 7, 14 and 21 for regional differences in total DNA, glycosaminoglycan (GAG) and collagen (COL) content as well as the expression of aggrecan (AGG), collagen type I and type II (COL1/2) and matrix metalloproteinase 3 and 13 (MMP3/13). Stress-relaxation indentation testing was performed to investigate regional mechanical properties of the electrospun constructs. Electrospinning into a conductive mould yielded stable 3D constructs both initially and for the whole in vitro culture period, with an equilibrium modulus in the MPa range. Rapid cell proliferation and COL accumulation was observed until week 3. Quantitative real time PCR analysis showed an initial increase in AGG, no change in COL2, a persistent increase in COL1, and only a slight decrease initially for MMP3. Electrospinning of fibrous scaffolds directly into an auricle-shape represents a promising option for auricular tissue engineering, as it can reduce the steps needed to achieve an implantable structure.

Electrospinning Auricular Shaped Scaffolds for Tissue Engineering

Poly(ɛ)caprolactone scaffolds have been electrospun directly into an auricular shaped conductive mould. Bovine chondrocytes were harvested from articular cartilage and seeded onto 16 of the produced scaffolds, which received either an ethanol (group A) or a plasma treatment (group B) for sterilisation before seeding. The seeded scaffolds were cultured for 3 weeks in vitro and analysed with regard to total DNA and GAG content as well as the expression of AGG, COL1, COL2, MMP3 and MMP13. Rapid cell proliferation and GAG accumulation was observed until week 2. However, total DNA and GAG content decreased again in week 3. qPCR data shows a slight increase in the expression of anabolic genes and a slight decrease for the catabolic genes, with a significant difference between the groups A and B only for COL2 and MMP13.