Joël Teuscher

Efficient Hybrid Solar Cells Based on Meso-Superstructured Organometal Halide Perovskites

Perovskite Photovoltaics For many types of low-cost solar cells, including those using dye-sensitized titania, performance is limited by low open-circuit voltages. Lee et al. (p. 643, published online 4 October; see the Perspective by Norris and Aydil) have developed a solid-state cell in which structured films of titania or alumina nanoparticles are solution coated with a lead-halide perovskite layer that acts as the absorber and n-type photoactive layer. These particles are coated with a spirobifluorene organic-hole conductor in a solar cell with transparent oxide and metal contacts. For the alumina particles, power conversion efficiencies of up to 10.9% were obtained. Mesostructured alumina acts as an insulating scaffold for the assembly of very thin films of n- and p-type semiconductors. The energy costs associated with separating tightly bound excitons (photoinduced electron-hole pairs) and extracting free charges from highly disordered low-mobility networks represent fundamental losses for many low-cost photovoltaic technologies. We report a low-cost, solution-processable solar cell, based on a highly crystalline perovskite absorber with intense visible to near-infrared absorptivity, that has a power conversion efficiency of 10.9% in a single-junction device under simulated full sunlight. This “meso-superstructured solar cell” exhibits exceptionally few fundamental energy losses; it can generate open-circuit photovoltages of more than 1.1 volts, despite the relatively narrow absorber band gap of 1.55 electron volts. The functionality arises from the use of mesoporous alumina as an inert scaffold that structures the absorber and forces electrons to reside in and be transported through the perovskite.

Impedance Spectroscopic Analysis of Lead Iodide Perovskite-Sensitized Solid-State Solar Cells

Mesoscopic solid-state solar cells based on the inorganic-organic hybrid perovskite CH3NH3PbI3 in conjunction with the amorphous organic semiconductor spiro-MeOTAD as a hole transport material (HTM) are investigated using impedance spectroscopy (IS). A model to interpret the frequency response of these devices is established by expanding and elaborating on the existing models used for the liquid and solid-state dye-sensitized solar cells. Furthermore, the influence of changing the additive concentrations of tert-butylpyridine and LiTFSI in the HTM and varying the HTM overlayer thickness on top of the sub-micrometer thick TiO2 on the extracted IS parameters is investigated. The internal electrical processes of such devices are studied and correlated with the overall device performance. In particular, the features in the IS responses that are attributed to the ionic and electronic transport properties of the perovskite material and manifest as a slow response at low frequency and an additional RC element at intermediate frequency, respectively, are explored.

Influence of the Donor Size in D−π–A Organic Dyes for Dye-Sensitized Solar Cells

We report two new molecularly engineered push-pull dyes, i.e., YA421 and YA422, based on substituted quinoxaline as a π-conjugating linker and bulky-indoline moiety as donor and compared with reported IQ4 dye. Benefitting from increased steric hindrance with the introduction of bis(2,4-dihexyloxy)benzene substitution on the quinoxaline, the electron recombination between redox electrolyte and the TiO2 surface is reduced, especially in redox electrolyte employing Co(II/III) complexes as redox shuttles. It was found that the open circuit photovoltages of IQ4, YA421, and YA422 devices with cobalt-based electrolyte are higher than those with iodide/triiodide electrolyte by 34, 62, and 135 mV, respectively. Moreover, the cells employing graphene nanoplatelets on top of gold spattered film as a counter electrode (CE) show lower charge-transfer resistance compared to platinum as a CE. Consequently, YA422 devices deliver the best power conversion efficiency due to higher fill factor, reaching 10.65% at AM 1.5 simulated sunlight. Electrochemical impedance spectroscopy and transient absorption spectroscopy analysis were performed to understand the electrolyte influence on the device performances with different counter electrode materials and donor structures of donor-π-acceptor dyes. Laser flash photolysis experiments indicate that even though the dye regeneration of YA422 is slower than that of the other two dyes, the slower back electron transfer of YA422 contributes to the higher device performance.

Efficient Electron Transfer and Sensitizer Regeneration in Stable π-extended Tetrathiafulvalene-Sensitized Solar Cells

The development of metal-free organic sensitizers is a key issue in dye-sensitized solar cell research. We report successful photovoltaic conversion with a new class of stable tetrathiafulvalene derivatives, showing surprising electrochemical and kinetic properties. With time-resolved spectroscopy we could observe highly efficient regeneration of the photo-oxidized tetrathiafulvalene sensitizers, which were attached to a mesoporous TiO(2) film, by a redox mediator in the pores (iodide/tri-iodide), even though the measured driving force for regeneration was only approximately 150 mV. This important proof-of-concept shows that sensitizers with a small driving force, i.e. the oxidation potential of the sensitizer is separated from the redox potenial of the mediator by as little as 150 mV, can operate functionally in dye-sensitized solar cells and eventually aid to reduce photovoltage losses due to poor energetic alignment of the materials.

Unreacted PbI2 as a Double-Edged Sword for Enhancing the Performance of Perovskite Solar Cells

Lead halide perovskites have over the past few years attracted considerable interest as photo absorbers in PV applications with record efficiencies now reaching 22%. It has recently been found that not only the composition but also the precise stoichiometry is important for the device performance. Recent reports have, for example, demonstrated small amount of PbI2 in the perovskite films to be beneficial for the overall performance of both the standard perovskite, CH3NH3PbI3, as well as for the mixed perovskites (CH3NH3)x(CH(NH2)2)(1-x)PbBryI(3-y). In this work a broad range of characterization techniques including X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), photo electron spectroscopy (PES), transient absorption spectroscopy (TAS), UV-vis, electroluminescence (EL), photoluminescence (PL), and confocal PL mapping have been used to further understand the importance of remnant PbI2 in perovskite solar cells. Our best devices were over 18% efficient, and had in line with previous results a small amount of excess PbI2. For the PbI2-deficient samples, the photocurrent dropped, which could be attributed to accumulation of organic species at the grain boundaries, low charge carrier mobility, and decreased electron injection into the TiO2. The PbI2-deficient compositions did, however, also have advantages. The record Voc was as high as 1.20 V and was found in PbI2-deficient samples. This was correlated with high crystal quality, longer charge carrier lifetimes, and high PL yields and was rationalized as a consequence of the dynamics of the perovskite formation. We further found the ion migration to be obstructed in the PbI2-deficient samples, which decreased the JV hysteresis and increased the photostability. PbI2-deficient synthesis conditions can thus be used to deposit perovskites with excellent crystal quality but with the downside of grain boundaries enriched in organic species, which act as a barrier toward current transport. Exploring ways to tune the synthesis conditions to give the high crystal quality obtained under PbI2-poor condition while maintaining the favorable grain boundary characteristics obtained under PbI2-rich conditions would thus be a strategy toward more efficiency devices.

Charge Density Dependent Mobility of Organic Hole‐Transporters and Mesoporous TiO2 Determined by Transient Mobility Spectroscopy: Implications to Dye‐Sensitized and Organic Solar Cells

Transient mobility spectroscopy (TMS) is presented as a new tool to probe the charge carrier mobility of commonly employed organic and inorganic semiconductors over the relevant range of charge densities. The charge density dependence of the mobility of semiconductors used in hybrid and organic photovoltaics gives new insights into charge transport phenomena in solid state dye sensitized solar cells.

Blue-coloured highly efficient dye-sensitized solar cells by implementing the diketopyrrolopyrrole chromophore.

The paradigm shift in dye sensitized solar cells (DSCs) – towards donor- π bridge-acceptor (D-π-A) dyes – increases the performances of DSCs and challenges established design principles. Framed by this shifting landscape, a series of four diketopyrrolopyrrole (DPP)-based sensitizers utilizing the donor-chromophore-anchor (D-C-A) motif were investigated computationally, spectroscopically, and fabricated by systematic evaluation of finished photovoltaic cells. In all cases, the [Co(bpy)3]3+/2+ redox-shuttle afforded superior performance compared to I3−/I−. Aesthetically, careful molecular engineering of the DPP chromophore yielded the first example of a high-performance blue DSC – a challenge unmet since the inception of this photovoltaic technology: DPP17 yields over 10% power conversion efficiency (PCE) with the [Co(bpy)3]3+/2+ electrolyte at full AM 1.5 G simulated sun light.

Towards Compatibility between Ruthenium Sensitizers and Cobalt Electrolytes in Dye‐Sensitized Solar Cells

This tuning minimizes energy losses in the device byoptimizingthedrivingforceforregeneration,whichallowsforconsiderableimprovementoftheopen-circuitvoltagerelativeto iodine electrolytes.Current ruthenium(II) sensitizers are not designed toperform with cobalt electrolytes. Among the few examplesreported in the literature,

Photoinduced Interfacial Electron Injection Dynamics in Dye-Sensitized Solar Cells under Photovoltaic Operating Conditions

We report a pump-probe spectroscopy study of electron injection rates in dye-sensitized solar cell (DSSC) devices. We examine the case of working devices employing an N719 ruthenium sensitizer and an iodide electrolyte. Electron injection is found to occur mainly on a sub-100 fs time scale, followed by a slower component with a lifetime of 26.9 ps, in accordance with previous reports on model samples. The amplitude of this latter component varies with electrolyte composition from 25 to 9%. The appearance of slower components in the electron injection dynamics may be attributed to an aggregated or weakly bound state of the surface-adsorbed N719 sensitizer. Further measurements are reported varying the cell light bias and load conditions, revealing no influence on electron injection dynamics. No other electron injection event is found to occur up to 1 ns. These results show no evidence for a slowdown of electron injection under working conditions compared to model systems for the electrolytes examined in this study.

A panchromatic anthracene-fused porphyrin sensitizer for dye-sensitized solar cells

The development of ruthenium-free sensitizers which absorb light over a broad range of the solar spectrum is important for improving the power conversion efficiency of dye-sensitized solar cells. Here we study three chemically tailored porphyrin-based dyes. We show that by fusing the porphyrin core to an anthracene unit, we can extend the conjugation length and lower the optical gap, shifting the absorption spectrum into the near-infrared (NIR). All three dyes were tested in dye-sensitized solar cells, using both titanium dioxide and tin dioxide as the electron-transport material. Solar cells incorporating the anthracene-fused porphyrin dye exhibit photocurrent collection at wavelengths up to about 1100 nm, which is the longest reported for a porphyrin-based system. Despite extending the photon absorption bandwidth, device efficiency is found to be low, which is a common property of cells based on porphyrin dyes with NIR absorption. We show that in the present case the efficiency is reduced by inefficient electron injection into the oxide, as opposed to dye regeneration, and highlight some important design considerations for panchromatic sensitizers.