José Ferreira Costa

Effect of different polishing systems on the surface roughness of microhybrid composites

The use of composite resins in dentistry is well accepted for restoring anterior and posterior teeth. Many polishing protocols have been evaluated for their effect on the surface roughness of restorative materials. This study compared the effect of different polishing systems on the surface roughness of microhybrid composites. Thirty-six specimens were prepared for each composite [Charisma® (Heraeus Kulzer), Fill Magic® (Vigodent), TPH Spectrum® (Dentsply), Z100® (3M/ESPE) and Z250® (3M/ESPE)] and submitted to surface treatment with Enhance® and PoGo® (Dentsply) points, sequential Sof-Lex XT® aluminum oxide disks (3M/ESPE), and felt disks (TDV) combined with Excel® diamond polishing paste (TDV). Average surface roughness (Ra) was measured with a mechanical roughness tester. The data were analyzed by two-way ANOVA with repetition of the factorial design and the Tukey-Kramer test (p<0.01). The F-test result for treatments and resins was high (p<0.0001 for both), indicating that the effect of the treatment applied to the specimen surface and the effect of the type of resin on surface roughness was highly significant. Regarding the interaction between polishing system and type of resin used, a p value of 0.0002 was obtained, indicating a statistically significant difference. A Ra of 1.3663 was obtained for the Sof-Lex/TPH Spectrum interaction. In contrast, the Ra for the felt disk+paste/Z250 interactions was 0.1846. In conclusion, Sof-Lex polishing system produced a higher surface roughness on TPH Spectrum resin when compared to the other interactions.

Influence of human and bovine substrate on the microleakage of two adhesive systems

The aim of this study was to evaluate in vitro the marginal sealing of two adhesive systems and to analyze the influence of human and bovine substrates on marginal microleakage in enamel. Rectangular-shaped class V cavities (4 mm wide × 2 mm high × 2 mm deep) were made as follows: 8 cavities were prepared on the buccal and lingual surfaces of the human teeth with margins located on enamel and 16 cavities were prepared on the buccal surfaces of the bovine teeth. The cavities were randomly assigned to 4 groups of 8 cavities according to the adhesive system and substrate: G1 - Prime & Bond 2.1 (Dentsply)/human substrate; G2 - Adhese (Ivoclar/Vivadent)/human substrate; G3 - Prime & Bond 2.1 (Dentsply)/bovine substrate; G4 - Adhese (Ivoclar/Vivadent)/bovine substrate. The cavities were filled with microhybrid composite resin (Fillmagic) and after polishing/finishing procedures, the teeth were subjected to a thermocycling regimen of 500 cycles with 1-min immersions in water at 55° ±2°C and 5° ± 2°C. Next, the teeth were coated with two layers of nail polish to within 1 mm of the margin, submerged in a 50% silver nitrate solution for 2 h, rinsed thoroughly in running tap and immersed in developing solution for 8 h. The restorations were bisected resulting in 16 specimens. Microleakage was observed under a stereomicroscope at x25 and recorded using four-point (0-3) scoring system. The data were analyzed statistically by the Mann Whitney U-test at 5% significance level. Leakage was present in all specimens and there was statistically significant difference between the adhesive systems. Adhese self-etching system showed significantly more leakage in both substrates (human - p= 0.0001 and bovine - p= 0.0031). There was no statistically significant difference between human and bovine substrates for either of the adhesive systems based on different bonding mechanisms (Prime & Bond 2.1 - p= 0.6923 and Adhese - p= 0.6109). Neither of the adhesive systems was capable to completely prevent microleakage and the self-etching system was more susceptible to microleakage.

Characterization of two Ni–Cr dental alloys and the influence of casting mode on mechanical properties

PURPOSE The aim of this study was to evaluate the tensile strength, elongation, microhardness (MHV), composition and microstructure of two Ni-Cr based alloy, cast under different casting conditions. METHODS Before casting, the alloy ingots were evaluated as regards composition (EDX) and microstructure (Optical microscopy, SEM and EDX). The casting conditions were as follows: electromagnetic induction in an environment controlled with argon (EWA), electromagnetic induction in an environment under vacuum (EWV), electromagnetic induction without atmosphere control (EWNC) and blowtorch (BT). For each condition, 16 specimens were obtained, each measuring 25 mm high and 2.5mm in diameter. The ultimate tensile strength (UTS) and elongation (EL) tests were performed in a Kratos machine (1.0mm/min). Fractured specimens were embedded in bakelite resin and polished for Vickers Microhardness analysis (1000 g/10s) with 4 penetrations in each specimen. The UTS, EL and MHV results were evaluated for two-way ANOVA and Tukeys test (α=0.05). RESULTS The cross-product interaction was statistically significant for all properties evaluated (p<0.0001), lower UTS, VHN and high elongation means were observed for the Ni-Cr-Mo-Be alloy tested when cast under the induction/argon (p<0.05). Higher UTS means were found for Ni-Cr-Mo-Ti alloy tested when cast under the induction/vacuum, and induction/air and flame/air condition (p<0.05). The two alloys show a microstructure with a dendritic formation with the presence of eutectic presence. CONCLUSION The Ni-Cr-Mo-Ti alloy showed high UTS, MHV and lowest EL comparaded with the tradicional Ni-Cr-Mo-Be, that show lowest UTS, MHV and higher EL when cast on induction/argon.

Influence of alloy microstructure on the microshear bond strength of basic alloys to a resin luting cement

The aim of this study was to evaluate the influence of microstructure and composition of basic alloys on their microshear bond strength (µSBS) to resin luting cement. The alloys used were: Supreme Cast-V (SC), Tilite Star (TS), Wiron 99 (W9), VeraBond II (VBII), VeraBond (VB), Remanium (RM) and IPS d.SIGN 30 (IPS). Five wax patterns (13 mm in diameter and 4mm height) were invested, and cast in a centrifugal casting machine for each basic alloy. The specimens were embedded in resin, polished with a SiC paper and sandblasted. After cleaning the metal surfaces, six tygon tubes (0.5 mm height and 0.75 mm in diameter) were placed on each alloy surface, the resin cement (Panavia F) was inserted, and the excess was removed before light-curing. After storage (24 h/37°C), the specimens were subjected to µSBS testing (0.5 mm/min). The data were subjected to a one-way repeated measures analysis of variance and Turkeys test (α=0.05). After polishing, their microstructures were revealed with specific conditioners. The highest µSBS (mean/standard deviation in MPa) were observed in the alloys with dendritic structure, eutectic formation or precipitation: VB (30.6/1.7), TS (29.8/0.9), SC (30.6/1.7), with the exception of IPS (31.1/0.9) which showed high µSBS but no eutectic formation. The W9 (28.1/1.5), VBII (25.9/2.0) and RM (25.9/0.9) showed the lowest µSBS and no eutectic formation. It seems that alloys with eutectic formation provide the highest µSBS values when bonded to a light-cured resin luting cement.

Characterization of aqueous silver nitrate solutions for leakage tests

Objectives To determine the pH over a period of 168 h and the ionic silver content in various concentrations and post-preparation times of aqueous silver nitrate solutions. Also, the possible effects of these factors on microleakage test in adhesive/resin restorations in primary and permanent teeth were evaluated. Material and Methods A digital pHmeter was used for measuring the pH of the solutions prepared with three types of water (purified, deionized or distilled) and three brands of silver nitrate salt (Merck, Synth or Cennabras) at 0, 1, 2, 24, 48, 72, 96 and 168 h after preparation, and storage in transparent or dark bottles. Ionic silver was assayed according to the post-preparation times (2, 24, 48, 72, 96, 168 h) and concentrations (1, 5, 25, 50%) of solutions by atomic emission spectrometry. For each sample of each condition, three readings were obtained for calculating the mean value. Class V cavities were prepared with enamel margins on primary and permanent teeth and restored with the adhesive systems OptiBond FL or OptiBond SOLO Plus SE and the composite resin Filtek Z-250. After nail polish coverage, the permanent teeth were immersed in 25% or 50% AgNO3 solution and the primary teeth in 5% or 50% AgNO3 solutions for microleakage evaluation. ANOVA and the Tukeys test were used for data analyses (α=5%). Results The mean pH of the solutions ranged from neutral to alkaline (7.9±2.2 to 11.8±0.9). Mean ionic silver content differed depending on the concentration of the solution (4.75±0.5 to 293±15.3 ppm). In the microleakage test, significant difference was only observed for the adhesive system factor (p=0.000). Conclusions Under the tested experimental conditions and based on the obtained results, it may be concluded that the aqueous AgNO3 solutions: have neutral/alkaline pH and service life of up to 168 h; the level of ionic silver is proportional to the concentration of the solution; even at 5% concentration, the solutions were capable of indicating loss of marginal seal in the composite restorations; the 3-step conventional adhesive system had better performance regarding microleakage in enamel on primary and permanent teeth.

streptococcus mutans : Examining Factors Underlying Bacterial Colonizationin Mother-child Dyads and Early Childhood Caries: Examining Factors Underlying Bacterial Colonization

This study investigated the association between colonization of mother-child dyads with Streptococcus mutans (SM) and early childhood caries (ECC), with consideration of the mediator and confounders, using a theoretical model. Four hundred mothers and their children from São Luís, Brazil, were included in the study. A diagram based on directed acyclic graphs was elaborated to analyze the association between SM colonization of the mother, mediated by child SM, and ECC. Other maternal (socioeconomic, waist circumference, sugar consumption, DMFT index, and visible plaque) and child factors (sugar consumption, visible plaque, and child age) composed the theoretical model. A total effect model (maternal SM on ECC) and a direct effect model, adjusted by the mediation effect of child SM (maternal SM via child SM) on ECC, were analyzed. The outcome of interest in this study was ECC (number of teeth with caries experience, dmft), which was analyzed as a discrete variable by Poisson regression. The Paramed test was used to analyze mediation. The following variables were associated with ECC in the total effect model: maternal SM, maternal waist circumference ≥80 cm, DMFT, maternal visible plaque, child age ≥4 years, and increased sugar consumption of the child (>3 times/day). In the direct effect model, high maternal SM levels remained associated with ECC, while moderate and high colonization of the child with SM was also associated with ECC. Child SM colonization just partially mediated the effect of maternal SM on ECC (33%). Thus, factors other than the mechanism of bacterial colonization should be considered in mother-child dyads, including eating habits, oral hygiene practices, and a family history of caries.

Association between early childhood caries and maternal caries status: A cross-section study in São Luís, Maranhão, Brazil.

Objective: This study aims to evaluate the association between early childhood caries (ECC) and maternal caries status, and the maternal perception of ECC risk factors. Materials and Methods: A cross-sectional study was carried out with 77 mother-child pairs, the children ranging from 12 to 36 months of age and their mothers, who were seeking dental care at a health center in São Luís, Maranhão, Brazil. Data collection was conducted using a specific questionnaire for mothers. Oral clinical examination of the mother-child binomial to assess caries incidence, gingival bleeding (GB) and visible plaque was done. Home visits were performed in 10% of the sample in order to observe the environmental conditions, dietary habits and dental hygiene practices. Results: The findings showed that the caries prevalence in children was 22.5 times higher in the mother who had decayed tooth (prevalence ratio [PR] = 22.5, confidence interval [CI] 95% = 3.2-156.6, P < 0.001). GB also was observed in 14 mothers and children, the PR in pair was 12.2 (CI95% = 1.6-88.9, P < 0.001). The variables are related for the mother-child binomial in regression linear analysis. Conclusion: The maternal caries status was associated with ECC.

Proinflammatory cytokines in early childhood caries: Salivary analysis in the mother/children pair

HighlightsHigh consumption of added sugars has been associated with caries and obesity.VEGF were correlated with caries, waist circumference and sugar intake in mothers.IL‐6 are correlated with the severity of caries in the mother‐children pair. &NA; Hypothesis: Proinflammatory cytokines are increased in saliva of mother/children pairs with caries. Design: Case‐control study involving caries‐free children (n = 20) and children with early childhood caries (ECC) (n = 20), and their mothers (n = 40). The maternal variables analyzed were waist circumference (WC), decayed, missing and filled teeth (DMFT) and sugar intake; and in the children were body mass index (BMI), def‐t and sugar intake. Salivary levels of VEGF, IL‐6 and TNF‐&agr; were analyzed of mother/children pairs. Results: In the mothers, salivary VEGF levels were correlated with DMFT (r = 0.35; p = .03), WC (r = 0.35; p = .02), and sugar intake (r = 0.32; p = .04). Higher salivary IL‐6 levels were also correlated with maternal DMFT (r = 0.45; p = .004) and WC (r = 0.32; p = .04). In the children, higher salivary VEGF levels were correlated with higher def‐t scores (r = 0.42; p = .008). Children with caries had a 63% higher median salivary VEGF and twofold higher mean IL‐6 levels compared to caries‐free children. Mothers of children with ECC showed higher mean of salivary IL‐6 levels compared to those of children without ECC (p = .03). Conclusion: Salivary proinflammatory cytokines are correlated with the severity of caries in the mother‐children pair. Obesity and excessive sugar consumption seem to underlie the associations between proinflammatory cytokines and caries in the family environment.

Parameters that influence microtensile bond testing of adhesive systems

The aim of this study was to provide a critical review of the literature regarding factors that can interfere with microtensile test results for enamel and dentin adhesive systems. Primarily, reports in English, Spanish, or Portuguese that were published between July 1994 and September 2009 and are catalogued in MEDLINE and BBO were used. Additionally, we compiled relevant articles found in the references of these articles and dissertations and theses available in electronic databases of Brazilian universities that examined factors that can influence implementation of the microtensile test at each stage. The search strategy included searching for the following key term groups: microtensile and test; microtensile and assay; microtensile and test and parameters; microtensile and test and factors; microtensile and specimen; microtraccon and especimen. We reviewed 25 selected articles and found that they showed that even after adjustment of test parameters, changes found in the dentin could be responsible for variations observed amongst results. This influence could potentially be reduced by using the cohesive strength value of dentin adjacent to the adhesive interface as a standard for comparison, but more studies are needed to confirm whether such an approach would be reliable. Data analysis methodology should be taken into account when comparing studies.

Avaliação dos Hábitos Alimentares de Pacientes Adultos Submetidos ao Tratamento Ortodôntico

Resumen pt: Objetivo: Avaliar os habitos alimentares de pacientes que estao sendo submetidos ao tratamento ortodontico, abordando interrelacoes entre saude bucal e n...