Joydip Sengupta

Influence of annealing temperature on the structural, topographical and optical properties of sol–gel derived ZnO thin films

Abstract This investigation deals with the effect of annealing temperature on the structural, topographical and optical properties of Zinc Oxide thin films prepared by sol–gel method. The structural properties were studied using X-ray diffraction and the recorded patterns indicated that all the films had a preferred orientation along (002) plane and the crystallinity along with the grain size were augmented with annealing temperature. The topographical modification of the films due to heat treatment was probed by atomic force microscopy which revealed that annealing roughened the surface of the film. The optical properties were examined by a UV–visible spectrophotometer which exhibited that maximum transmittance reached nearly 90% and it diminished with increasing annealing temperature.

Effect of annealing on the structural, topographical and optical properties of sol–gel derived ZnO and AZO thin films

Abstract A comparative study of the physical properties of undoped Zinc Oxide (ZnO) and Al doped Zinc Oxide (AZO) thin films were performed as a function of annealing temperature. The structural properties were analyzed using X-ray diffraction and the recorded patterns indicated that the crystallinity of the films always enhanced with increasing annealing temperature while it degrades with Al doping. The topographical modification of the films due to heat treatment was examined by atomic force microscopy which revealed that annealing roughened the surface of all the films; however the AZO films always exhibited smoother morphology than ZnO. Study of the optical properties by UV-Visible spectrophotometer demonstrated that the transmittance was gradually diminished with the rise in annealing temperature. In addition, a notable increase in the optical band gap was also observed for the AZO films.

The effect of Fe and Ni catalysts on the growth of multiwalled carbon nanotubes using chemical vapor deposition

The effect of Fe and Ni catalysts on the synthesis of carbon nanotubes (CNTs) using atmospheric pressure chemical vapor deposition (APCVD) was investigated. Field emission scanning electron microscopy (FESEM) analysis suggests that the samples grow through a tip growth mechanism. High-resolution transmission electron microscopy (HRTEM) measurements show multiwalled carbon nanotubes (MWCNTs) with bamboo structure for Ni catalyst while iron filled straight tubes were obtained with the Fe catalyst. The X-ray diffraction (XRD) pattern indicates that nanotubes are graphitic in nature and there is no trace of carbide phases in both the cases. Low frequency Raman analysis of the bamboo-like and filled CNTs confirms the presence of radial breathing modes (RBM). The degree of graphitization of CNTs synthesized from Fe catalyst is higher than that from Ni catalyst as demonstrated by the high frequency Raman analysis. Simple models for the growth of bamboo-like and tubular catalyst filled nanotubes are proposed.

Structural and optical properties of post annealed Mg doped ZnO thin films deposited by the sol–gel method

Abstract Thin films of magnesium doped zinc oxide (MZO) were synthesized using the sol–gel method and annealed at different temperatures under ambient condition. The morphological properties of the post annealed MZO films were investigated using X-ray diffraction (XRD) while atomic force microscopy (AFM) was employed to probe the topographical alteration of the films. The optical properties of the post annealed MZO films were examined by UV-visible spectroscopy and the Tauc method was used to estimate the optical band gap. The studies revealed that, with the rise of annealing temperature the crystallinity and the surface roughness of the MZO films were increased whereas the optical transmittance and the energy bandgap were decreased.

An atomic force microscopy and optical microscopy study of various shaped void formation and reduction in 3C-SiC films grown on Si using chemical vapor deposition

The formation of various uncommon shaped voids along with regular triangular and square voids in the epitaxial 3C-SiC films on Si has been investigated by optical microscopy and atomic force microscopy. Heteroepitaxial growth of 3C-SiC films on Si (001) and (111) substrates has been performed using hexamethyldisilane in a resistance-heated chemical vapor deposition reactor. The influence of the orientation of the Si substrate in determining the shape of the voids has clearly been observed. In addition, the growth period and the growth-temperature have been considered as the major parameters to control the size, density and shape of the voids. Generally, voids are faceted along {111} planes, but depending upon growth conditions, other facets with higher surface energy have also been observed. Finally the size and density of the voids are remarkably reduced, by suitable growth technique.

Effect of growth temperature on the CVD grown Fe filled multi-walled carbon nanotubes using a modified photoresist

Fe filled carbon nanotubes were synthesized by atmospheric pressure chemical vapor deposition using a simple mixture of iron(III) acetylacetonate (Fe(acac){sub 3}) with a conventional photoresist and the effect of growth temperature (550-950 {sup o}C) on Fe filled nanotubes has been studied. Scanning electron microscopy results show that, as the growth temperature increases from 550 to 950 {sup o}C, the average diameter of the nanotubes increases while their number density decreases. High resolution transmission electron microscopy along with energy dispersive X-ray investigation shows that the nanotubes have a multi-walled structure with partial Fe filling for all growth temperatures. The graphitic nature of the nanotubes was observed via X-ray diffraction pattern. Raman analysis demonstrates that the degree of graphitization of the carbon nanotubes depends upon the growth temperature.

Carbon nanotube synthesis from propane decomposition on a pre-treated Ni overlayer

Growth of carbon nanotubes (CNTs) was performed by atmospheric pressure chemical vapour deposition (APCVD) of propane on Si(111) with a pre-treated Ni overlayer acting as a catalyst. Prior to the growth of CNTs, a thin film of Ni was deposited on Si(111) substrate by evaporation and heat treated at 900°C. The growth of nanotubes was carried out at 850°C using propane as a source of carbon. Distribution of the catalyst particles over the Si substrate was analysed before and after heat treatment by atomic force microscopy (AFM). The X-ray diffraction (XRD) pattern of the grown material revealed that they are graphitic in nature. Field emission scanning electron microscopy (FESEM) was used to investigate the growth process and it was found that a catalytic particle was always situated at the tip of the tube thus implying a tip growth mechanism. Evidence for the presence of radial breathing mode from multi-wall nanotubes (MWNTs) in the grown sample was obtained from micro-Raman analysis. Finally, high-resolution transmission electron microscopic (HRTEM) analysis confirmed that the graphene layers of the CNTs are well ordered with typical 0·34 nm spacing.

Pre-heating effect on the catalytic growth of partially filled carbon nanotubes by chemical vapor deposition.

The surface reconstruction of the Fe catalyst films due to high temperature processing in hydrogen prior to nanotube nucleation and its effect on the growth morphologies of partially filled carbon nanotubes (CNTs) synthesized using atmospheric pressure chemical vapor deposition (APCVD) of propane was investigated. Results show that pre-heating of the catalyst film deeply influences the particle size distribution, which governs the growth morphologies of the corresponding CNTs. The distribution of the catalyst particles over the Si substrate was analyzed before and after the heat treatment by atomic force microscopy (AFM) which reveals that heat treatment causes clusters of catalyst to coalesce and form macroscopic islands. The X-ray diffraction (XRD) pattern of the grown material indicates that they are graphitic in nature. Scanning electron microscopy (SEM) analysis suggested that the growth density strongly depends on the pre heat treatment of the Fe catalyst film. Multiwalled CNTs with partial catalyst filling were observed via high-resolution transmission electron microscopy (HRTEM) measurements. The degree of graphitization of the CNTs also depends on the pre heating as demonstrated by Raman analysis. A simple model for the growth of partially catalyst filled nanotubes is proposed.

A Comparative Study of the Synthesis of Carbon Nanotubes Using Ni and Fe as Catalyst

The effect of Fe and Ni catalysts on the synthesis of carbon nanotubes (CNTs) using atmospheric pressure chemical vapor deposition (APCVD) was investigated. Distribution of the catalyst particles over the Si substrate was analyzed by atomic force microscopy (AFM). Characterization by X-ray diffraction analysis (XRD), field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM) and Raman spectroscopic measurements over the grown species is reported. The study clearly shows that the catalyst strongly influences morphology and microstructure of the grown CNTs.