Jw O'Reilly

Identification of homemade inorganic explosives by ion chromatographic analysis of post-blast residues

Anions and cations of interest for the post-blast identification of homemade inorganic explosives were separated and detected by ion chromatographic (IC) methods. The ionic analytes used for identification of explosives in this study comprised 18 anions (acetate, benzoate, bromate, carbonate, chlorate, chloride, chlorite, chromate, cyanate, fluoride, formate, nitrate, nitrite, perchlorate, phosphate, sulfate, thiocyanate and thiosulfate) and 12 cations (ammonium, barium(II), calcium(II), chromium(III), ethylammonium, magnesium(II), manganese(II), methylammonium, potassium(I), sodium(I), strontium(II), and zinc(II)). Two IC separations are presented, using suppressed IC on a Dionex AS20 column with potassium hydroxide as eluent for anions, and non-suppressed IC for cations using a Dionex SCS 1 column with oxalic acid/acetonitrile as eluent. Conductivity detection was used in both cases. Detection limits for anions were in the range 2-27.4ppb, and for cations were in the range 13-115ppb. These methods allowed the explosive residue ions to be identified and separated from background ions likely to be present in the environment. Linearity (over a calibration range of 0.05-50ppm) was evaluated for both methods, with r(2) values ranging from 0.9889 to 1.000. Reproducibility over 10 consecutive injections of a 5ppm standard ranged from 0.01 to 0.22% relative standard deviation (RSD) for retention time and 0.29 to 2.16%RSD for peak area. The anion and cation separations were performed simultaneously by using two Dionex ICS-2000 chromatographs served by a single autoinjector. The efficacy of the developed methods was demonstrated by analysis of residue samples taken from witness plates and soils collected following the controlled detonation of a series of different inorganic homemade explosives. The results obtained were also confirmed by parallel analysis of the same samples by capillary electrophoresis (CE) with excellent agreement being obtained.

Chromatographic and electrophoretic separation of inorganic sulfur and sulfur–oxygen species

A review is presented of the use of chromatographic and electrophoretic methods for the separation of inorganic sulfur species in aqueous matrices, with particular emphasis on ion chromatographic methods. The species considered are elemental sulfur, sulfide, polysulfides (Sx2−), sulfite, sulfate, thiosulfate, dithionate, polythionates (SxO62−) and metal–thiosulfate complexes. A brief introduction to sulfur anion chemistry is given, followed by a discussion of the separation and determination of sulfur species using ion chromatography, capillary electrophoresis and other separation-based techniques. Difficulties inherent in the analysis of complex sulfur anion mixtures are indicated and the procedures that have been used to overcome these difficulties are also examined.

Standards in the extraction phase, a new approach to calibration of microextraction processes

A standard, preloaded onto the extraction phase prior to the extraction step, partially desorbs to the sample matrix during sampling. The amount lost can be used as a means of calibration.

Retention behaviour of strong acid anions in ion-exclusion chromatography on sulfonate and carboxylate stationary phases

Some factors influencing the retention of strong-acid anions on ion-exclusion columns were investigated using columns with sulfonate and carboxylate functional groups. The nature of the functional group on the resin, the eluent pH and the eluent ionic strength all significantly affected the retention and separation of these analytes. Retention was observed for all strong-acid anions over the eluent pH range 2.2-5.7 and increased with both decreasing eluent pH and increasing eluent ionic strength. Some separation of strong-acid anions was possible when using a resin with carboxylate functional groups. It has also been demonstrated that strong-acid anions are poor markers of column void volume for ion-exclusion chromatography. A more accurate value was obtained using the neutral polymeric material dextran blue. When using eluents of low ionic strength, poor or fronted peak shapes were observed. A mechanism for these observations is proposed that relates the shape to ionic strength changes across the peak. A system peak was encountered under most experimental conditions. The properties of this peak are discussed and a cause for the system peak postulated.

Separation of polythionates and the gold thiosulfate complex in gold thiosulfate leach solutions by ion-interaction chromatography

A method for the separation of the polythionates (SxO6(2-), x = 3-5) in gold thiosulfate leach solutions using ion-interaction chromatography with conductivity and ultraviolet (UV) detection is described. Polythionates were eluted within 18 min using an eluent comprising an acetonitrile step gradient at 0.0 min from 15% v/v to 28% v/v, 3 mM TBAOH, and 2.5 mM sodium carbonate, operated using a Dionex NS1-5 micron column with guard. The developed method was capable of separating the gold thiosulfate complex ion in standard solutions, but quantification of this species in realistic leach solutions proved impractical due to a self-elution effect that caused the gold peak to be eluted as a broad band. Detection limits for polythionates using a 10 microL injection volume ranged between 1-6 mg L(-1) (5-23 microM) for conductivity and 0.8-13 mg L(-1) (4-68 microM) for UV detection, based on a signal-to-noise ratio of 2. Calibration was linear over the ranges 5-2000, 10-2000 and 25-2500 mg L(-1) for trithionate, tetrathionate and pentathionate, respectively. The technique was applied successfully to leach liquors containing 0.5 M ammonium thiosulfate, 2 M ammonia, 0.05 M copper sulfate and 20 % m/v gold ore.