Kiyoshi Horikawa

TWO-DIMENSIONAL BEACH TRANSFORMATION DUE TO WAVES

The steady state profile of the longshore current induced by regular, obliquely incident, breaking waves, over a bottom with arbitrary parallel bottom contours, is predicted. A momentum approach is adopted. The wave parameters must be given at a depth outside the surf zone, where the current velocity is very small. The variation of the bottom roughness along the given bottom profile must be prescribed in advance. Depth refraction is included also in the calculation of wave set-down and set-up. Current refraction and rip-currents are excluded. The model includes two new expressions, one for the calculation of the turbulent lateral mixing, and one for the turbulent bottom friction. The term for the bottom friction is non-linear. Rapid convergent numerical algorithms are described for the solution of the governing equations. The predicted current profiles are compared with laboratory experiments and field measurements. For a plane sloping bottom, the influence of different eddy viscosities and constant values of bottom roughness is examined.The calculation of turbulent flow using Naviers equations assumes the introduction of a turbulent viscosity coefficient the value of which is normally constant, conforming with Boussinesqs hypothesis. It was shown that setting aside this hypothesis, a velocity profile quite different to that resulting from the classic theory is obtained in the case of flow induced by wind. This result appears to be confirmed by the tests carried out in the Mediterranean. The advantage of this method is that it gives the vertical turbulent diffusion which is of particular interest to pollution studies.In the numerical method of prediction of wind waves in deep water, Hasselmanns nonlinear interaction theory is applied. This method assumes the energy balance of individual component waves. However, the total energy balance must exist in the transformation of irregular waves in shoaling water. In this investigation, experiments were carried out on the transformations in shoaling water of composite waves having two components and random waves having one or two main peaks. It was found that the elementary component wave height of the composite waves and the elementary peak power of the random waves decrease with decrease in the water depth. This reason can be explained qualitatively by the theory of the elementary component wave height change of finite amplitude waves in shoaling water. The secondary component wave height of the composite waves and the secondary peak power of the random waves increase with decrease in the water depth. This can be explained qualitatively by Hamadas theory of nonlinear interaction in uniform depth.Experiments have been carried out by using non-breaking waves and breaking waves to investigate the wave forces on a vertical circular cell located in the shallow water. Based on the experimental data, the drag coefficient and the inertia coefficient of a circular cylinder and the curling factor of breaking waves are estimated, and the computation methods of wave forces are examined. As a result, it is shown that the phase lag of inertia forces behind the accelerations of water particles should be considered for the estimation of the drag coefficient as well as the inertia coefficient. In addition the previous formula of the maximum breaking wave forces acting on a cell or a pile is revised by introducing the effects of the above-mentioned phase lag and another phase difference, both of which are functions of the ratio of the cell diameter to the wave length. • It is confirmed that the proposed formula is applicable even to the large cell with the diameter comparable to the wave length. INTRODUCTION Many studies have been done on the impulsive pressures acting on a vertical wall, but there has been very little investigation of breaking wave forces on a cell-type structure. The breaking wave forces should be taken into consideration all the same in the design of pile-type or cell-type structures in nearshore area, because breaking waves cause extreme shock pressures on a cell structure asThe air bubble plume induced by the steady release of air into water has been analyzed with an integral technique based on the equations for conservation of mass, momentum and buoyancy. This approach has been widely used to study the behavior of submerged turbulent jets and plumes. The case of air-bubble induced flow, however, includes additional features. In this study the compressibility of the air and the differential velocity between the rising air bubbles ,and the water are introduced as basic propertie s of the air bubble plume in addition to a fundamental coefficient of entrainment and a turbulent Schmidt number characterizing the lateral spreading of the air bubbles. Theoretical solutions for twoand three-dimensional air-bubble systems in homogeneous, stagnant water are presented in both dimensional and normalized form and compared to existing experimental data. The further complication of a stratified environment is briefly discussed since this case is of great practical interest. This paper is to be considered as a progress report, as future experimental verification of various hypotheses is needed.

SEDIMENT TRANSPORT UNDER SHEET FLOW CONDITION

The cost of many coastal projects is often increased by the expensive beach repair and maintenance required to remedy the destabilising effects of structures on the adjoining coastline. Physical and/or mathematical models have been developed for use in planning these projects in order to predict and quantify the effects of marine sediment transport on the coastal topography. Such models need to be calibrated against prototype data and one method of gauging volumetric sediment movement is by successive bathymetric/ topographic profiting surveys which are performed seasonally and annually. Since large quantities of sediment are related to small changes in bed elevation it is clear that this profiling needs to be done with the utmost precision* The areas most affected extend from the beach through the surf zone to water depths of about 25 metres. The surf zone in particular is a dynamic and hostile area which falls outside the traditional activities of both the hydrographic and land surveyors. Consequently innovative methods, deficient in sound survey principle and practice, have often been pursued in this area without any attempt being made to assess the tolerance on the data. This paper attempts to show that it is possible to produce reliable and verifiable results to the required accuracy by using conventional survey equipment and techniques, also by taking the necessary precautions against the many possible sources of survey error. The procedures and techniques described have evolved from NRIOs involvement over the past decade in major projects at Richards Bay, Durban, Koeberg and in False Bay. The results of a recent verification investigation are fully reported in this paper.Besides wave impact forces, erosion of the inner side of a sea dike is a serious cause of destruction. Therefore, wave run-up and overtopping effects have to be considered with respect to the safety of a dike. Strong relations were found between both these influences (TAUTENHAIN et.al., 1980, 1981, 1982), based on experiments in a wave flume and using an energy conservation concept. However, under natural conditions, an oblique wave approach has to be considered. This paper deals with the influence of wave direction on wave runup on a smooth dike slope in order to provide a basis for calculating the overtopping rates for both regular and irregular waves.This paper describes a study carried out at Port Taranaki, New Plymouth, New Zealand to determine ships track and motions at the port entrance. The results of the study being used to establish the extent (plan area) and optimum depth of proposed capital dredging works. The time lapse photographic technique, incorporating reference levels and bearings in each frame, used to record vessels entering and leaving the port is described, Maximum increases in ships draft due to sea conditions are given.N.S.L. program is a finite-difference code for two dimensionnal flows with a free surface in a vertical plane. Basic equations are Navier-Stokes Equations with a simple simulation of turbulent effects by an eddy viscosity coefficient related to the mixing length and the mean velocity gradient. Theses equations are solved in a variable domain in time. The main features of the numerical method are presented. Some comparisons with theoretical solutions give a good validation of the code both in linear and non linear cases. Other examples of application are given.The design of the coal unloading terminal in an unprotected environment created the need to develop design criteria as well as operational and structural systems that will respond toproblems arising from unloading bulk in the open sea. As there was no known precedent of an unprotected unloading terminal, the criteria was based on experience in existing offshore loadina terminals, laboratory tests and engineering judgement.A large number of man-made tidal swimming pools (two examples are shown in Figure 1) exist along the South African coast. They are usually situated on rocky outcrops in the close vicinity of popular sandy bathing beaches to provide protected bathing conditions in these areas mainly for children and elderly people. Some tidal pools, especially along rocky coast, provide the only safe bathing facilities. Besides affording protection against waves and surfzone currents the pools provide protection from sharks. A large number of tidal pools were built during the early 1950s along the Natal South Coast after the occurrence of a relatively large number of shark attacks on bathers on that coast. The semi-diurnal tide with a range of about 1,5 m along the South African coast makes it possible for pools to be built such that water replenishment can occur during every high-water (approximately every 12 hours) during both neap and spring tide periods. Presently, there exists a great need for more tidal pools as part of the demand for more recreational facilities along the South African coast. However, no information on design criteria could be found in the literature.The objective of this research is to study the prediction method of hurricane waves around this island, especially in the Taiwan Strait. The paper describes the prediction of hurricane waves used by Bretchneiders (1976) Method and finds out the predicted waves are different from measured waves, therefore the Bretchneider predicted model is modified by the authors and then the modified model is applied to predict waves again. It is found out that predicted waves match well with the measured waves. The results of the modified Bretchneider model are compared with those of the Ijima tracing method and find out the former is better than the latter. The second part is to apply the modified model to predict the extreme value of wave heights and compute the worse hurricane wave condition of the surrounding sea area around island, within recent score year (1959-1978). The calculated sites are Chu-Wei, Nan-Liaw, Ta-Shih, Cheng-Kung, Pu-Tai, Tung-Kang, Nan-Wan as shown in Fig.1 and Shiau Liu- Chieu totally 8 stations. Then use the Gumbel Distribution TYPE 1 to predict the extreme wave height of each returned period.In the design and construction of waterfront bulkhead systems, it is essential to consider the coastal effects of tides, waves, boat wakes, currents, bottom sediment movement and bottom scour. Many improperly designed bulkhead systems experience severe loss of backfill and toe materials with the bulkhead eventually failing if it is not corrected in time. Inadequate drainage, joint connections, and/or inadequate toe protection are typically the causes of failure. This paper describes an investigation of a bulkhead system supporting a large waterfront development in southern California which was experiencing widespread sinkhole development in the bulkheads backfill and was on the verge of losing toe material. The objective of this investigation was to determine the extent and cause of ongoing subsurface erosion, to evaluate its effect on the bulkhead stability, and to recommend and design mitigative measures. The cause of the erosion was determined to be piping of fine grained soils due to inadequate backfill drainage. A remedial drainage scheme was designed and field-tested, and several structural repair schemes were suggested for portions of the bulkhead where accumulated damage affected the integrity of the structure.

FIELD EXPERIMENTS ON LONGSHORE SAND TRANSPORT IN THE SURF ZONE

The cost of many coastal projects is often increased by the expensive beach repair and maintenance required to remedy the destabilising effects of structures on the adjoining coastline. Physical and/or mathematical models have been developed for use in planning these projects in order to predict and quantify the effects of marine sediment transport on the coastal topography. Such models need to be calibrated against prototype data and one method of gauging volumetric sediment movement is by successive bathymetric/ topographic profiting surveys which are performed seasonally and annually. Since large quantities of sediment are related to small changes in bed elevation it is clear that this profiling needs to be done with the utmost precision* The areas most affected extend from the beach through the surf zone to water depths of about 25 metres. The surf zone in particular is a dynamic and hostile area which falls outside the traditional activities of both the hydrographic and land surveyors. Consequently innovative methods, deficient in sound survey principle and practice, have often been pursued in this area without any attempt being made to assess the tolerance on the data. This paper attempts to show that it is possible to produce reliable and verifiable results to the required accuracy by using conventional survey equipment and techniques, also by taking the necessary precautions against the many possible sources of survey error. The procedures and techniques described have evolved from NRIOs involvement over the past decade in major projects at Richards Bay, Durban, Koeberg and in False Bay. The results of a recent verification investigation are fully reported in this paper.Besides wave impact forces, erosion of the inner side of a sea dike is a serious cause of destruction. Therefore, wave run-up and overtopping effects have to be considered with respect to the safety of a dike. Strong relations were found between both these influences (TAUTENHAIN et.al., 1980, 1981, 1982), based on experiments in a wave flume and using an energy conservation concept. However, under natural conditions, an oblique wave approach has to be considered. This paper deals with the influence of wave direction on wave runup on a smooth dike slope in order to provide a basis for calculating the overtopping rates for both regular and irregular waves.This paper describes a study carried out at Port Taranaki, New Plymouth, New Zealand to determine ships track and motions at the port entrance. The results of the study being used to establish the extent (plan area) and optimum depth of proposed capital dredging works. The time lapse photographic technique, incorporating reference levels and bearings in each frame, used to record vessels entering and leaving the port is described, Maximum increases in ships draft due to sea conditions are given.N.S.L. program is a finite-difference code for two dimensionnal flows with a free surface in a vertical plane. Basic equations are Navier-Stokes Equations with a simple simulation of turbulent effects by an eddy viscosity coefficient related to the mixing length and the mean velocity gradient. Theses equations are solved in a variable domain in time. The main features of the numerical method are presented. Some comparisons with theoretical solutions give a good validation of the code both in linear and non linear cases. Other examples of application are given.The design of the coal unloading terminal in an unprotected environment created the need to develop design criteria as well as operational and structural systems that will respond toproblems arising from unloading bulk in the open sea. As there was no known precedent of an unprotected unloading terminal, the criteria was based on experience in existing offshore loadina terminals, laboratory tests and engineering judgement.A large number of man-made tidal swimming pools (two examples are shown in Figure 1) exist along the South African coast. They are usually situated on rocky outcrops in the close vicinity of popular sandy bathing beaches to provide protected bathing conditions in these areas mainly for children and elderly people. Some tidal pools, especially along rocky coast, provide the only safe bathing facilities. Besides affording protection against waves and surfzone currents the pools provide protection from sharks. A large number of tidal pools were built during the early 1950s along the Natal South Coast after the occurrence of a relatively large number of shark attacks on bathers on that coast. The semi-diurnal tide with a range of about 1,5 m along the South African coast makes it possible for pools to be built such that water replenishment can occur during every high-water (approximately every 12 hours) during both neap and spring tide periods. Presently, there exists a great need for more tidal pools as part of the demand for more recreational facilities along the South African coast. However, no information on design criteria could be found in the literature.The objective of this research is to study the prediction method of hurricane waves around this island, especially in the Taiwan Strait. The paper describes the prediction of hurricane waves used by Bretchneiders (1976) Method and finds out the predicted waves are different from measured waves, therefore the Bretchneider predicted model is modified by the authors and then the modified model is applied to predict waves again. It is found out that predicted waves match well with the measured waves. The results of the modified Bretchneider model are compared with those of the Ijima tracing method and find out the former is better than the latter. The second part is to apply the modified model to predict the extreme value of wave heights and compute the worse hurricane wave condition of the surrounding sea area around island, within recent score year (1959-1978). The calculated sites are Chu-Wei, Nan-Liaw, Ta-Shih, Cheng-Kung, Pu-Tai, Tung-Kang, Nan-Wan as shown in Fig.1 and Shiau Liu- Chieu totally 8 stations. Then use the Gumbel Distribution TYPE 1 to predict the extreme wave height of each returned period.In the design and construction of waterfront bulkhead systems, it is essential to consider the coastal effects of tides, waves, boat wakes, currents, bottom sediment movement and bottom scour. Many improperly designed bulkhead systems experience severe loss of backfill and toe materials with the bulkhead eventually failing if it is not corrected in time. Inadequate drainage, joint connections, and/or inadequate toe protection are typically the causes of failure. This paper describes an investigation of a bulkhead system supporting a large waterfront development in southern California which was experiencing widespread sinkhole development in the bulkheads backfill and was on the verge of losing toe material. The objective of this investigation was to determine the extent and cause of ongoing subsurface erosion, to evaluate its effect on the bulkhead stability, and to recommend and design mitigative measures. The cause of the erosion was determined to be piping of fine grained soils due to inadequate backfill drainage. A remedial drainage scheme was designed and field-tested, and several structural repair schemes were suggested for portions of the bulkhead where accumulated damage affected the integrity of the structure.

SAND TRANSPORT BY WIND ON A WET SAND SURFACE

This report will update the coastal zone practitioner on the National Flood Insurance Program (NFIP) as it affects the implementation of manmade changes along the coastline. It is our intent to place in proper perspective this fast-changing and often difficult to interpret national program. Readers will achieve an overall understanding of the NFIP on the coast, and will be in a position to apply the programs requirements in their efforts. We will begin with a history of the application of the NFIP to the coastal zone. The history of the problems encountered will lead into current regulations, methodologies, and the changes the Federal Emergency Management Agency plans for the future.The spatial variability of the nearshore wave field is examined in terms of the coherence functions found between five closely spaced wave gages moored off the North Carolina coast in 17 meters depth. Coherence was found to rapidly decrease as the separation distance increased, particularly in the along-crest direction. This effect is expressed as nondimensional coherence contours which can be used to provide an estimate of the wave coherence expected between two spatial positions.Prediction of depositional patterns in estuaries is one of the primary concerns to coastal engineers planning major hydraulic works. For a well-mixed estuary where suspended load is the dominant transport mode, we propose to use the divergence of the distribution of the net suspended load to predict the depositional patterns. The method is applied to Hangzhou Bay, and the results agree well qualitatively with measured results while quantitatively they are also of the right order of magnitude.

A STUDY ON WAVE TRANSFORMATION INSIDE SURF ZONE

INTRODUCTION For the design of a coastal structure, the height of its crown must be determined rationally and economically, taking into consideration the water level of the sea and its occurence probability. The water level in the sea is mainly referred to the astronomical tide, the meteorological effect and the short period wave. If component height according to these elements are given as; 3c, ; the tidal level, xr ; the level rise caused by meteorological origin, and x, ; the half height of wave, the level of the wave crest X at a certain tidal condition is shown by following equation under several assumption: I a i + X, + X, (1)

LABORATORY STUDY ON OSCILLATORY BOUNDARY LAYER FLOW

The distribution of bed-load sand transport normal to the beach has been measured m a series of field experiments conducted in the surf zone at Fernandma Beach, Florida. Simultaneous measurements were made of the waves and water particle motion at various locations in the surf zone. The energy flux of the waves was resolved Into Its longshore component from the measured directional and energy spectra. It Is found that the bed-load transport is related to the depth of water and longshore energy flux. Insight into the mechanics of sediment transport is obtained by comparing the wave and water particle motion energy spectra, which give a direct measure of the kinetic and potential energy, at various locations in the surf zone. INTRODUCTION A meaningful field investigation of the sand transport processes m the surf zone requires the synoptic measurement of a number of hydrodynamic and sediment variables. Fairly complete and extensive data are required to evaluate the validity of various proposed sand transport relationships and the formulations of new relationships where necessary. This paper describes field experiments conducted m the surf zone at Fernandma Beach, located on the northeastern coast of Florida. The emphasis of this study was to obtain information concerning the distribution of bedload transport perpendicular to shore and the physical processes causing such movement. Sediment transport m the surf zone can be considered as being caused by a combination of shear stresses due to wave and current action. An attempt to correlate sediment transport with physical parameters then must include good wave and current measurements. The experiments were conducted from October, 1966 to May, 1967, a period that encompasses the more intense wave activity along this coast. The beach and nearshore bottom profile is typically a one or two bar system with a gentle slope of two to three per cent. The sand has a mean grain size of approximately 0.2 millimeters. The mean tidal range is 1.7 meters.A summary is given of the results of training sixteen rivers in an endeavour to increase bar depths for navigation. The bars are of simple crescent formation fed by littoral drift. Whilst the training works have improved conditions for navigation they have not resulted in any appreciable increase in bar depths. Despite the complex mechanisms involved in bar formation a consistent simple correlation is found to exist between channel and bar depths. This correlation seems to apply to all rivers and inlets with simple bar systems and extends over a range from a bar depth of two feet to 60 feet. The correlation holds for rivers elsewhere and-- with varying climates of exposure.

Literature review of sand transport by wind on a dry sand surface

Abstract A critical and comprehensive literature survey of sand transport by wind on a dry sand surface is made from the perspective of engineering use. Principal findings are: (1) Most predictive expressions for the sand transport rate show a cubic dependence on the shear velocity, or obey a similar power law. (2) Some difference is found in the value of the multiplicative empirical coefficient in the various formulas, and much of the scatter may be ascribed to relative trap efficiency. (3) Verification of predictive formulas has mainly rested on laboratory measurements, and reliable but limited field verification has not been made until recently. (4) The laboratory and field data indicate that both the Bagnold and the Kawamura formulas are applicable to a well-sorted sand and can be used for estimation of wind-blown sand transport on dry natural beaches. Modifications have been made for a widely distributed sand and for fluctuating wind velocity.

SEDIMENT TRANSPORT AND BEACH TRANSFORMATION

The cost of many coastal projects is often increased by the expensive beach repair and maintenance required to remedy the destabilising effects of structures on the adjoining coastline. Physical and/or mathematical models have been developed for use in planning these projects in order to predict and quantify the effects of marine sediment transport on the coastal topography. Such models need to be calibrated against prototype data and one method of gauging volumetric sediment movement is by successive bathymetric/ topographic profiting surveys which are performed seasonally and annually. Since large quantities of sediment are related to small changes in bed elevation it is clear that this profiling needs to be done with the utmost precision* The areas most affected extend from the beach through the surf zone to water depths of about 25 metres. The surf zone in particular is a dynamic and hostile area which falls outside the traditional activities of both the hydrographic and land surveyors. Consequently innovative methods, deficient in sound survey principle and practice, have often been pursued in this area without any attempt being made to assess the tolerance on the data. This paper attempts to show that it is possible to produce reliable and verifiable results to the required accuracy by using conventional survey equipment and techniques, also by taking the necessary precautions against the many possible sources of survey error. The procedures and techniques described have evolved from NRIOs involvement over the past decade in major projects at Richards Bay, Durban, Koeberg and in False Bay. The results of a recent verification investigation are fully reported in this paper.Besides wave impact forces, erosion of the inner side of a sea dike is a serious cause of destruction. Therefore, wave run-up and overtopping effects have to be considered with respect to the safety of a dike. Strong relations were found between both these influences (TAUTENHAIN et.al., 1980, 1981, 1982), based on experiments in a wave flume and using an energy conservation concept. However, under natural conditions, an oblique wave approach has to be considered. This paper deals with the influence of wave direction on wave runup on a smooth dike slope in order to provide a basis for calculating the overtopping rates for both regular and irregular waves.This paper describes a study carried out at Port Taranaki, New Plymouth, New Zealand to determine ships track and motions at the port entrance. The results of the study being used to establish the extent (plan area) and optimum depth of proposed capital dredging works. The time lapse photographic technique, incorporating reference levels and bearings in each frame, used to record vessels entering and leaving the port is described, Maximum increases in ships draft due to sea conditions are given.N.S.L. program is a finite-difference code for two dimensionnal flows with a free surface in a vertical plane. Basic equations are Navier-Stokes Equations with a simple simulation of turbulent effects by an eddy viscosity coefficient related to the mixing length and the mean velocity gradient. Theses equations are solved in a variable domain in time. The main features of the numerical method are presented. Some comparisons with theoretical solutions give a good validation of the code both in linear and non linear cases. Other examples of application are given.The design of the coal unloading terminal in an unprotected environment created the need to develop design criteria as well as operational and structural systems that will respond toproblems arising from unloading bulk in the open sea. As there was no known precedent of an unprotected unloading terminal, the criteria was based on experience in existing offshore loadina terminals, laboratory tests and engineering judgement.A large number of man-made tidal swimming pools (two examples are shown in Figure 1) exist along the South African coast. They are usually situated on rocky outcrops in the close vicinity of popular sandy bathing beaches to provide protected bathing conditions in these areas mainly for children and elderly people. Some tidal pools, especially along rocky coast, provide the only safe bathing facilities. Besides affording protection against waves and surfzone currents the pools provide protection from sharks. A large number of tidal pools were built during the early 1950s along the Natal South Coast after the occurrence of a relatively large number of shark attacks on bathers on that coast. The semi-diurnal tide with a range of about 1,5 m along the South African coast makes it possible for pools to be built such that water replenishment can occur during every high-water (approximately every 12 hours) during both neap and spring tide periods. Presently, there exists a great need for more tidal pools as part of the demand for more recreational facilities along the South African coast. However, no information on design criteria could be found in the literature.The objective of this research is to study the prediction method of hurricane waves around this island, especially in the Taiwan Strait. The paper describes the prediction of hurricane waves used by Bretchneiders (1976) Method and finds out the predicted waves are different from measured waves, therefore the Bretchneider predicted model is modified by the authors and then the modified model is applied to predict waves again. It is found out that predicted waves match well with the measured waves. The results of the modified Bretchneider model are compared with those of the Ijima tracing method and find out the former is better than the latter. The second part is to apply the modified model to predict the extreme value of wave heights and compute the worse hurricane wave condition of the surrounding sea area around island, within recent score year (1959-1978). The calculated sites are Chu-Wei, Nan-Liaw, Ta-Shih, Cheng-Kung, Pu-Tai, Tung-Kang, Nan-Wan as shown in Fig.1 and Shiau Liu- Chieu totally 8 stations. Then use the Gumbel Distribution TYPE 1 to predict the extreme wave height of each returned period.In the design and construction of waterfront bulkhead systems, it is essential to consider the coastal effects of tides, waves, boat wakes, currents, bottom sediment movement and bottom scour. Many improperly designed bulkhead systems experience severe loss of backfill and toe materials with the bulkhead eventually failing if it is not corrected in time. Inadequate drainage, joint connections, and/or inadequate toe protection are typically the causes of failure. This paper describes an investigation of a bulkhead system supporting a large waterfront development in southern California which was experiencing widespread sinkhole development in the bulkheads backfill and was on the verge of losing toe material. The objective of this investigation was to determine the extent and cause of ongoing subsurface erosion, to evaluate its effect on the bulkhead stability, and to recommend and design mitigative measures. The cause of the erosion was determined to be piping of fine grained soils due to inadequate backfill drainage. A remedial drainage scheme was designed and field-tested, and several structural repair schemes were suggested for portions of the bulkhead where accumulated damage affected the integrity of the structure.

BEACH PROFILES AND ON-OFFSHORE SEDIMENT TRANSPORT

Parameter Identification (PI) algorithm is an optimization procedure that systematically searches the parameters embedded in a mathematical model. These parameters are not measurable from a physical point of view. The optimization is based on the minimization of a selected norm of the differences between the solution of the mathematical model and scattered observations collected from the system. Parameter identification (or inverse problem) has been studied in groundwater systems extensively for the past decade (15), and it has also drawn many researchers in the fields of open-channel flow and estuarine modeling since 1972 (1,2,9,17). All the past estuarine PI works in the literature are confined to the one-dimensional case, and hydrodynamics and transport equations are treated separately. This study deals with PI in a two-dimensional vertically-averaged estuarine salinity model. The salinity transport equation is coupled with the hydrodynamics equations. The coupled relationship introduces extra density terms in the hydrodynamics equations, which must be solved simultaneously with the transport equation. One of the most difficult problems in PI is the collection of needed observations from the system which is being modeled. With limited exception, the currently available data from the prototype estuaries are not adequate for the purposes of developing a PI algorithm. This is usually critical in quantity (the number of stations and/or the period of time) and in quality (noise of data). However, if an operational hydraulic model is available, the data could then be obtained economically and accurately under an ideally controlled environment. The large amount of data that can be collected from a hydraulic model of an estuary will provide a sufficient number of observations and the required initial and boundary conditions for the development of a PI algorithm. The use of the estuary hydraulic model could provide a better source of prototype data than would be available from the real estuary. It will be much easier to distinguish between the inadequacy of the mathematics and the inadequacy of our understanding of the prototype. Thus, it will give us an idea of how well we could expect to mathematically model the real estuary if we had an unlimited amount of prototype data. Additionally, when these types of data are used in PI, parameters can be optimally identified and the mathematical model can then be used conjunctively with the hydraulic model for prototype applications, provided that the mathematical model is consistently formulated. How well a hydraulic model simulates the prototype estuary is not considered in this study.The problem of buoyant surface jet (BSJ) is relevant from the practical standpoint to the discharge of cooling water of power plants into the receiving water bodies. The buoyant surface jet has extensively been studied by numerous investigators both theoretically and experimentally. Most studies have been concerned with the problems of BSJ discharged horizontally into a surface of a deep ambient water with or without cross current. From a practical standpoint, however, the design engineers are often confronted with the design of thermal outfalls in the coastal regions which are frequently shallow and have the boundary effects. Few investigators have studied the problem of BSJ discharged horizontally over slopping bottom into quiescent receiving water (1), (2), (4), (5), (6), and (7). However, no information on the foregoing problem with moving ambient water is available. The purpose of this paper is (a) to present the experimental results of BSJ which is discharged over slopping bottom into moving ambient water, and (b) to see the degree of error which is introduced by applying the deep water integral models to the case of a buoyant surface jet with a bottom boundary.This study deals with the statistical properties of the group formation of random waves determined by the zero-up-cross method. Probability distributions about (1) the run of high waves (2) the total run (3) the run of resonant wave period are derived theoretically providing that the time series of wave height and wave period form the Markov chain. Transition probabilities are given by the 2-dimensional Rayleigh distribution for the wave height train and the 2-dimensional Weibull distribution for the wave period train. And very good agreements between data and the theoretical distributions have been obtained. Then the paper discusses those parameters which affect the statistical properties of the runs and shows that the spectrum peakedness parameter for the. run of wave height and the spectrum width parameter for the run of wave period are the most predominant.One of the characteristics of the North Sea between the British Isles, the Netherlands, Germany and Denmark is the occurrence of heave storm surges especially in autumn and winter with heights of about 4 m above spring highwater. Coastal areas and especially the estuaries of the tidal rivers are hit by these storm surge events. The mean tidal range at the German coast comes to about 3 m with relatively low daily and semimonthly inequalities of less than 0.5m. Within the framework of long-term developments of the navigation channels of the estuaries as well as of the storm surge protection works, physical model tests had to be carried out in order to predict the influences of such measures on the storm surge heights to be expected.A two-dimensional laboratory investigation of sediment transport, induced by shallow-water waves, showed that the sediment motion over suspension-dominant asymmetric ripples is closely related to the development of eroding beaches. High-speed motion picture analysis revealed that vortices, formed over this type of ripple, play a crucial role in transporting the sediment to the offshore region. A relation for net offshore sediment flux was formulated for sand 0.02 cm in diameter. A simple model for eroding beaches was proposed and its validity was checked by using two existing data sets for 0.02-cm sand beaches; the model could predict fairly well profile and shoreline changes in the early stages.Queenslands Beach Protection Act (1968-1974) resulted, inter alia in the formation of the Beach Protection Authority, which is responsible for investigating coastal erosion, planning remedial works, recording and evaluating results of investigations, and various other functions. Control of windblown sand and retention of vegetated and naturally stable coastal sand dunes are valuable means of decreasing coastal erosion and because of this the Authority implements a broad research program into the management of coastal dunes in Queensland. Field trials are carried out at the Authoritys Dune Management Research Station on South Stradbroke Island to determine methods of repairing, stabilizing and managing coastal dunes. The research program conducted so far consists of fifteen separate field trials within four general areas of investigation:- (a) Dune Forming Fences Two trials were installed in blown-out sections of the frontal dune to compare different types of semi-permeable fences (eg. wooden slats) and brush matting (a surface mulch of tree branches) on the basis of their ability to accumulate windblown sand and initiate dune formation. (b) Dune Stabilization Techniques Three trials were installed on bare dunal areas to evaluate methods of temporary sand surface stabilization (organic mulches and spray-on materials) as an aid in establishing dune vegetation. (c) Dune Vegetation Two trials were conducted to produce and compile information on the performance of important or potentially useful dune plants. (d) Plant Nutrition Eight trials using different combinations and rates of fertilizer were used to study methods of improvement of establishment and early growth of dune stabilizing plants, particularly sand spinifex grass (Spinifex hirsutus). Good establishment and rapid early growth is required in order to accelerate, improve, and decrease the costs of, the stabilization process.Construction of the Jebel Ali Port complex, 35 km southwest of Dubai, in the United Arab Emirates, has included the disposal of 110 Million cubic metres of excavated spoil. Disposal of dredged carbonaceous breccia raised particular problems due to the high proportion of fines generated and which, unless properly controlled, could cause wide scale environmental damage in the coastal zone. At the same time it was necessary that acceptable reclamation should be created. An extensive data collection exercise was carried out in order to monitor the geotechnical, hydraulic, meteorological, marine climate and marine biology aspects of the operation.Tung-Kang Fishing Harbor, which is about 16 km to the south of Kaohsiung Harbor, is a river harbor on the south-west coast of Taiwan. This harbor is located at the estuary of the Niu-Pu River, which meets the Tung- Kang River and the Kao-Ping River on the north side, (see Fig. 1) The original north and south jetties were constructed in 1959. Because the entrance is located at the meeting of the three rivers and the water depth at the entrance is shallower than that in the breaking zone, the entrance is easily chocked with sand during the summer season when the south-west wind and waves are strong. Therefore, dredging is always necessary to maintain the required depth. On. the other hand, because of the increasing number of fishing boats and deeper draft, the port cannot function effectively. There-fore, how to keep the required water depth at the entrance and to obtain a wider and stable water basin is an urgent problem with this harbor. Based on the sounding of 1973, the littoral drift is mainly from the south. In the next year the construction of a 176 m long new south jetty was begun to protect the entrance and to facilitate the sedimentation study. In 1975, the Taiwan Fisheries Consultants was appointed to undertake the investigation and long-term planning work. This project includes littoral process study, planning, model test and design. Finally it is recommended that an adequate layout of south and north jetties can solve the problem of accretation of the harbor entrance. The purpose of this paper is to describe some aspects with emphasis on how to prevent the shoaling of the entrance channel located at the meeting of the rivers.

OBSERVATION OF NEARSHORE CURRENT AND EDGE WAVES

The equations describing conservation of mass, momentum and energy in a turbulent free surface flow are derived for a controle volume extending over the whole depth. The effect of the turbulent surface oscillations are discussed but neglected in the following analysis, where the equations are applied to the energy balance in a surf zone wave motion. This leads to results for the wave height variation and the velocity of propagation. The results cannot be reconciled completely with measurements and the concluding discussion is aimed at revealing how the model can be improved.A three-dimensional morphodynamic model of sequential beach changes Is presented. The model Is based on variations in breaker wave power generating a predictable sequence of beach conditions. The spectrum of beach conditions from fully eroded-dissipatlve to fully accreted reflective is characterised by ten beach-stages. Using the breaker wave power to beach-stage relationship the model Is applied to explain temporal, spatial and global variations In beach morphodynamlcs.The agents of initial damage to the dunes are water, which undermines them, and animals (including man) which damage the protective vegetation by grazing or trampling. Of these, man has recently assumed predominant local importance because of the popularity of sea-side holidays and of the land-falls of certain marine engineering works such as oil and gas pipelines and sewage outfalls. The need is therefore increasing for active dune management programmes to ensure that under these accentuated pressures, the coast retain an equilibrium comparable with that delicately balanced equilibrium which obtains naturally at a particular location.