L. Bartolomé

Bioanalytical chromatographic method validation according to current regulations, with a special focus on the non-well defined parameters limit of quantification, robustness and matrix effect.

Method validation is a mandatory step in bioanalysis, to evaluate the ability of developed methods in providing reliable results for their routine application. Even if some organisations have developed guidelines to define the different parameters to be included in method validation (FDA, EMA); there are still some ambiguous concepts in validation criteria and methodology that need to be clarified. The methodology to calculate fundamental parameters such as the limit of quantification has been defined in several ways without reaching a harmonised definition, which can lead to very different values depending on the applied criterion. Other parameters such as robustness or ruggedness are usually omitted and when defined there is not an established approach to evaluate them. Especially significant is the case of the matrix effect evaluation which is one of the most critical points to be studied in LC-MS methods but has been traditionally overlooked. Due to the increasing importance of bioanalysis this scenario is no longer acceptable and harmonised criteria involving all the concerned parties should be arisen. The objective of this review is thus to discuss and highlight several essential aspects of method validation, focused in bioanalysis. The overall validation process including common validation parameters (selectivity, linearity range, precision, accuracy, stability…) will be reviewed. Furthermore, the most controversial parameters (limit of quantification, robustness and matrix effect) will be carefully studied and the definitions and methodology proposed by the different regulatory bodies will be compared. This review aims to clarify the methodology to be followed in bioanalytical method validation, facilitating this time consuming step.

Distribution and bioaccumulation of PAHs in the UNESCO protected natural reserve of Urdaibai, Bay of Biscay.

Along 10 campaigns, from June 2002 to September 2004, the concentrations of 16 polycyclic aromatic hydrocarbons (PAHs) were measured in sediments and oysters (Crassostrea sp.) taken from four sites in the Unesco protected natural reserve of Urdaibai (Basque Country, Bay of Biscay). Total PAH concentration ranged from 0.7 to 140 microg kg(-1) (dw) in the case of sediments, and from 300 to 1400 microg kg(-1) (dw) in the case of oysters. During this study, the coast of the Bay of Biscay was severely affected by the Prestige oil spill (November 2002). Presumably, as a consequence of this accident, both spatial and temporal variations of the PAHs, as well as the sources of the PAHs were affected by the oil spill, and this effect was observed in the total concentrations and, especially, in several diagnostic ratios and in multivariate data analysis. Finally, both BAF (bioaccumulation factor) and BSAF (biota-sediment accumulation factor) parameters were calculated to conclude that particulate matter seems to be the most favourable uptake pathway of PAHs in oysters from this estuary.

Retention-time locked methods in gas chromatography.

Retention time is one of the most important chromatographic features for analytical chemists since it is the key parameter to separate, identify and quantify compounds of interest from complex mixtures. Although detectors with higher-dimensional signals ease the identification of many components, there are demanding requirements on the retention time, particularly when high-throughput methods are considered. In addition to this, gas chromatographic elution shows significant run-to-run variations due to fluctuations in temperature and pressure, column degradation or matrix effects. In this sense, different approaches have been developed to minimise those variations: the introduction of electronic pneumatic control (EPC) systems, which allow a very efficient control of the flow of the carrier gas, the use of peak alignment algorithms to treat the chromatograms, or the use of retention-time locking (RTL). The RTL is a feature of the Agilent ChemStation software available for those GC instruments equipped with EPC systems. Originally it was developed to assure method translation but it has extended to fix the retention time and to implement peak deconvolution algorithms and database building and searching facilities. In this manuscript, the RTL basis and practical aspects are summarised together with a brief description of some applications.

Hollow fibre-based liquid-phase microextraction technique combined with gas chromatography–mass spectrometry for the determination of pyrethroid insecticides in water samples

A simple, easy-to-use, efficient and environmentally friendly method has been developed for the simultaneous analysis of nine pirethroid pesticides in water samples by the combination of hollow fibre-based liquid-phase microextraction (HF-LPME) and gas chromatography-mass spectrometry (GC/MS). For the developed method, nine pirethroid pesticides (esbiothrin, prallethrin, bifenthrin, tetramethrin, phenothrin, permethrin, cyfluthrin, cypermethrin and deltamethrin) were concentrated and well separated under optimal conditions. Several factors that influence the efficiency of HF-LPME were investigated and optimized by means of experimental design. The proposed method has good linearity in the concentration range of 10-400 μg L(-1) with correlation coefficients between 0.995 and 0.999. Overall enrichment factors for the optimized method ranged from 139 to 255 times except for cypermethrin and deltamethrin which ranged from 35 to 128. Detection and quantitation limits of the chromatographic method were in the range of 0.002-0.012 μg L(-1) and 0.003-0.026 μg L(-1) respectively, with RSD values between 4.2% and 18.4%. The recoveries varied in the range of 69.4%-122.7% except for cypermethrin and deltamethrin (17.5%-64.1%) with relative standard deviations between 1.0% and 24.0% for intra and inter-day experiments at different concentrations (0.1 μg L(-1), 0.5 μg L(-1), 1 μg L(-1)). The HF-LPME method optimized was applied to the analysis of three spiked real water samples with good results.

Analytical strategies based on multiple headspace extraction for the quantitative analysis of aroma components in mushrooms

Headspace (HS) and headspace solid phase microextraction (HS-SPME) analysis by gas chromatography-mass spectrometry (GC/MS) have been found to be suitable methods for the analysis of volatile organic compounds. The objectives of this paper are to study the possibilities of multiple headspace extraction (MHE) for the quantitative determination of volatile compounds in mushroom samples and to compare the results obtained using three different sample treatment techniques. For this purpose, HS with two different injection techniques (pressure-loop system and gas-tight syringe autosampling system) and HS-SPME have been studied. Three processes were optimized for the analysis of 20 volatile compounds by experimental design technique based on Central Composite Design (CCD) and Full Factorial Design depending on the used methodology. Once the designs were finished, a trade off among optimum conditions for each compound analyzed was reached. At optimum conditions, appropriate extraction time and sample amount for the three techniques used were established. Finally, the methods were validated in terms of linearity, detection and quantitation limits and repeatability. The most suitable method was then applied to the quantitative analysis of seven mushroom samples. A detailed comparison of the analytical performance characteristics of HS and HS-SPME as sample treatment techniques for final GC/MS determination is given. In addition, MHE has been proved to be an adequate technique to avoid matrix effects in complex samples quantitation. Its applicability to the determination of volatile mushroom components, along with its limitations, is discussed in this work.

Relevance study of bare and coated zero valent iron nanoparticles for lindane degradation from its by-product monitorization

Zero-valent iron nanoparticles (NZVI) as well as polymer-stabilized nanoparticles were synthesized and used for lindane (γ-hexachlorocyclohexane) degradation in aqueous solution. To study the effectiveness of the different coated nanoparticles, simple and rapid analytical methods have been developed to measure and to detect lindane and its by-products. For the monitorization of lindane degradation solid-phase extraction (SPE) was used, while volatile by-products formation measurement was carried out by headspace-solid phase microextraction (HS-SPME) followed by GC/MS. The SPE-GC/MS method provides low detection limits (0.2 μg L(-1)), high recovery (above 95%) and it is a valuable tool for kinetic studies of the degradation process for each polymer used, while HS-SPME-GC/MS has proved to be an effective tool for the extraction and evaluation of volatile degradation by-products.

DATINK pilot study: an effective methodology for ballpoint pen ink dating in questioned documents.

Establishing the approximate age of an ink entry from a questioned document is often a complicated task and a controversial issue in forensic sciences. Among the existing approaches, the analysis of solvents in ballpoint inks may be a useful parameter for determining the age of ink on paper. In recent years, several ink dating methods have been proposed. These methods have been based on the analysis of common ink solvents using gas chromatography/mass spectrometry (GC/MS) as the analytical platform. Despite these recent methods, several questions remain. The aim of this work was to develop an ink dating methodology (DATINK) for documents written by ballpoint pens based on the disappearance of volatile solvents from the ink entry. Multiple solid-phase microextraction (MHS-SPME) coupled to GC/MS was used to measure the solvents from ink entries made with four BIC(®) ballpoint pens. The β parameter, the remaining fraction of the analyte in the system after one equilibration, corresponding to the successive extractions was considered for modelling a mathematical equation for later ink age dating. Preliminary tests of DATINK method showed that it was possible to detect the presence of ink solvents on documents up to the studied five years. The analyses of different real samples of known age were analyzed in terms of β values, which provided a mean relative error of 21%. The proposed use of β parameter for estimating the absolute age of ballpoint ink entries has shown promising results with a standard deviation of β ranging from 0.002 to 0.004.

Effect of coating on the environmental applications of zero valent iron nanoparticles: the lindane case

Commercial stabilized slurry of zero-valent iron nanoparticles (nZVI) as well as laboratory-synthesized polymer-stabilized NZVI nanoparticles were used for lindane (γ-hexachlorocyclohexane) degradation studies in aqueous solution. In the present study, polymer-stabilized iron nanoparticles were stabilized using polyethylene glycol (PEG, Mn ~400 and ~950-1050) and polytetrahydrofuran (PTHF, Mn ~650). To study the effectiveness of the different nanoparticles, a quantitative monitorization of lindane degradation by using solid-phase extraction (SPE) and a qualitative measurement of generated volatile by-products by headspace-solid phase microextraction (HS-SPME) followed by GC/MS were carried out. The obtained data were compared and contrasted with the results obtained in previous work. Results showed that the nanoparticles studied in this work possess superior dechlorination performance compared with previous observations. The freshly prepared Fe(0)-PEG400, Fe(0)-PEG1050 and Fe(0)-PTHF exhibited high reactivity during the dechlorination process of lindane in a very short time. The results obtained with the synthesized nanoparticles were similar to those obtained with commercial nanoparticles. However, in all cases reactivity decreased at reactions late stage. Degradation of lindane by the studied nanoparticles removed 99.9% of the lindane initial concentration after 72h, except for Fe(0)-PTHF nanoparticles, for which the reaction stopped after 5min. In all cases, the reaction followed a second order kinetics. Finally, comparing the results from this study with our previous work, where different nature polymers were considered (Fe(0)-CMC, Fe(0)-PAA and Fe(0)-PAP), more gradual degradation profile of lindane was observed for Fe(0)-PAA and Fe(0)-CMC. It should be noted that in the present case, the reaction of lindane was speeded up with commercial and Fe(0)-PEG nanoparticles. Nevertheless, in the later case, the composition of by-products was affected by the presence of partially degraded intermediates. Taking into account the current technologies, the high removal rates obtained and the acceptable degradation times required, the proposed technology is suitable for its aimed purpose.

Preparation of a reference mussel tissue material for polycyclic aromatic hydrocarbons and trace metals determination

Due to high cost of certified reference materials (CRMs), reference materials (RMs) are preferred to check the method performance in environmental analysis. In this work, a laboratory reference material (LRM) was prepared and characterised to carry out the quality control in monitoring analysis of eight polycyclic aromatic hydrocarbons (PAHs) and nine trace metals in mussel tissue. Mussels were collected in a naturally polluted area. Before the reference material was bottled, the mussel tissue was stabilised by freeze-drying, ground and sieved. For the material characterisation, several statistical tests were applied to check the homogeneity of the analytes in the tissue, and a stability test was performed to study the effect of the storage temperature in the analyte concentration. Other characteristics such as specific density, moisture and lipid contents as well as particle size distribution of the material were determined. Although the LRM had a homogeneous distribution for all PAHs and almost all metals, the stability study showed different results at both storage temperatures studied. For both PAHs and trace metals, the material was suitable to assure the quality control of the analysis.

Acid alteration of several ignitable liquids of potential use in arsons

Ignitable liquids such as fuels, alcohols and thinners can be used in criminal activities, for instance arsons. Forensic experts require to know their chemical compositions, as well as to understand how different modification effects could impact them, in order to detect, classify and identify them properly in fire debris. The acid alteration/acidification of ignitable liquids is a modification effect that sharply alters the chemical composition, for example, of gasoline and diesel fuel, interfering in the forensic analysis and result interpretation. However, to date there is little information about the consequences of this effect over other accelerants of interests. In this research paper, the alteration by sulfuric acid of several commercial thinners and other accelerants of potential use in arsons is studied in-depth. For that purpose, spectral (by ATR-FTIR) and chromatographic (by GC-MS) data were obtained from neat and acidified samples. Then, the spectral and chromatographic modifications of each studied ignitable liquid were discussed, proposing several chemical mechanisms that explain the new by-products produced and the gradual disappearance of the initial compounds. Hydrolysis, Fischer esterification and alkylation reactions are involved in the modification of esters, alcohols, ketones and aromatic compounds of the studied ignitable liquids. This information could be crucial for correctly identifying these accelerants. Additionally, an exploratory analysis revealed that some of the most altered ignitable liquid samples might be very similar with each other, which could have impact on casework.