L.N. Acquaroli

Capillary Filling in Nanostructured Porous Silicon

An experimental study on the capillary filling of nanoporous silicon with different fluids is presented. Thin nanoporous membranes were obtained by electrochemical anodization, and the filling dynamics was measured by laser interferometry, taking advantage of the optical properties of the system, related with the small pore radius in comparison to light wavelength. This optical technique is relatively simple to implement and yields highly reproducible data. A fluid dynamic model for the filling process is also proposed including the main characteristics of the porous matrix (tortuosity, average hydraulic radius). The model was tested for different ambient pressures, porous layer morphology, and fluid properties. It was found that the model reproduces well the experimental data according to the different conditions. The predicted pore radii quantitatively agree with the image information from scanning electron microscopy. This technique can be readily used as nanofluidic sensor to determine fluid properties such as viscosity and surface tension of a small sample of liquid. Besides, the whole method can be suitable to characterize a porous matrix.

Optofluidic characterization of nanoporous membranes.

An optofluidic method that accurately identifies the internal geometry of nanochannel arrays is presented. It is based on the dynamics of capillary-driven fluid imbibition, which is followed by laser interferometry. Conical nanochannel arrays in anodized alumina are investigated, which present an asymmetry of the filling times measured from different sides of the membrane. It is demonstrated by theory and experiments that the capillary filling asymmetry only depends on the ratio H of the inlet to outlet pore radii and that the ratio of filling times vary closely as H(7/3). Besides, the capillary filling of conical channels exhibits striking results in comparison to the corresponding cylindrical channels. Apart from these novel results in nanoscale fluid dynamics, the whole method discussed here serves as a characterization technique for nanoporous membranes.

Enhanced photoconductivity and fine response tuning in nanostructured porous silicon microcavities

We used light confinement in optical microcavities to achieve a strong enhancement and a precise wavelength tunability of the electrical photoconductance of nanostructured porous silicon (PS). The devices consist of a periodic array of alternating PS layers, electrochemically etched to have high and low porosities – and therefore distinct dielectric functions. A central layer having a doubled thickness breaks up the symmetry of the one-dimensional photonic structure, producing a resonance in the photonic band gap that is clearly observed in the reflectance spectrum. The devices were transferred to a glass coated with a transparent SnO2 electrode, while an Al contact was evaporated on its back side. The electrical conductance was measured as a function of the photon energy. A strong enhancement of the conductance is obtained in a narrow (17nm FWHM) band peaking at the resonance. We present experimental results of the angular dependence of this photoconductance peak energy, and propose an explanation of the conductivity behaviour supported by calculations of the internal electromagnetic field. These devices are promising candidates for finely tuned photoresistors with potential application as chemical sensors and biosensors.

Current-voltage characteristics in macroporous silicon/SiOx/SnO2:F heterojunctions

We study the electrical characteristics of macroporous silicon/transparent conductor oxide junctions obtained by the deposition of fluorine doped-SnO2 onto macroporous silicon thin films using the spray pyrolysis technique. Macroporous silicon was prepared by the electrochemical anodization of a silicon wafer to produce pore sizes ranging between 0.9 to 1.2 μ m in diameter. Scanning electronic microscopy was performed to confirm the pore filling and surface coverage. The transport of charge carriers through the interface was studied by measuring the current-voltage curves in the dark and under illumination. In the best configuration, we obtain a modest open-circuit voltage of about 70 mV and a short-circuit current of 3.5 mA/cm2 at an illumination of 110 mW/cm2. In order to analyze the effects of the illumination on the electrical properties of the junction, we proposed a model of two opposing diodes, each one associated with an independent current source. We obtain a good accordance between the experimental data and the model. The current-voltage curves in illuminated conditions are well fitted with the same parameters obtained in the dark where only the photocurrent intensities in the diodes are free parameters.

Degradation Analysis of Encapsulated and Nonencapsulated TiO2/PTB7:PC70BM/V2O5 Solar Cells under Ambient Conditions via Impedance Spectroscopy

Inverted organic cells are promising devices for sustainable and low-cost future electric generation. In this work, we present the degradation mechanisms studied in ITO/TiO2/PTB7:PC70BM/V2O5/Ag inverted organic solar cells (iOSCs) by impedance spectroscopy (IS). Measurements were performed on encapsulated (controlled environment) and nonencapsulated (ambient condition) cells following their temporal evolution under AM1.5 illumination for several voltage biases. From the impedance spectra, analyzed in terms of resistive/capacitive equivalent circuits, we were able to identify that the most sensitive layers inside of the device are contact layers. According with presented, IS technique is useful for determining the materials that have more influence on the degradation of organic solar cells. We demonstrate that IS is a powerful technique to identify the limiting mechanisms and to establish the limiting materials inside of the iOSCs.