Lars Heepe

Joining the Un‐Joinable: Adhesion Between Low Surface Energy Polymers Using Tetrapodal ZnO Linkers

Tetrapodal ZnO crystals are used for mechanical interlocking of PTFE and cross-linked PDMS, classically non-adhesive polymers. This novel approach is straightforward and easily applicable and leads to a peel strength that is higher than 200 N m(-1) without chemical modification of the surfaces. The shape of these fillers emerged as a crucial aspect of the interlocking mechanism.

Suction component in adhesion of mushroom-shaped microstructure

To shed light on the role of suction in adhesion of microstructure with mushroom-shaped terminal elements, we compared pull-off forces measured at different retraction velocities on structured and smooth surfaces under different pressure conditions. The results obtained allow us to suggest that suction may contribute up to 10 per cent of the pull-off force measured on the structured surfaces at high velocities. We therefore conclude that the attachment ability of this biomimetic adhesive must not be solely based on van der Waals forces. Our experiments also suggest a change in visco-elastic properties of the structured surfaces compared with the bulk material. Based on the results obtained, it is assumed that this adhesive may be suitable in dynamic pick-and-drop processes even under vacuum conditions at which sufficiently high adhesive capability is maintained.

Adhesion tilt-tolerance in bio-inspired mushroom-shaped adhesive microstructure

We studied experimentally and theoretically the effect of different tilt angles on the adhesion of mushroom-shaped adhesive microstructures. The marginal measured influence of tilting on pull-off forces is quantitatively well confirmed by numerical and theoretical calculations and was shown to be a direct consequence of an optimized stress distribution. In addition, the presence of a joint-like narrowing under the contact elements, as found in some biological attachment systems, was shown to further contribute to the tilt-tolerance. The results obtained allow us to explain the advantage of the widely observed mushroom-shaped contact geometry in nature for long-term and permanent adhesion.

Ultrastructure of dragonfly wing veins: composite structure of fibrous material supplemented by resilin

Dragonflies count among the most skilful of the flying insects. Their exceptional aerodynamic performance has been the subject of various studies. Morphological and kinematic investigations have showed that dragonfly wings, though being rather stiff, are able to undergo passive deformation during flight, thereby improving the aerodynamic performance. Resilin, a rubber‐like protein, has been suggested to be a key component in insect wing flexibility and deformation in response to aerodynamic loads, and has been reported in various arthropod locomotor systems. It has already been found in wing vein joints, connecting longitudinal veins to cross veins, and was shown to endow the dragonfly wing with chordwise flexibility, thereby most likely influencing the dragonflys flight performance. The present study revealed that resilin is not only present in wing vein joints, but also in the internal cuticle layers of veins in wings of Sympetrum vulgatum (SV) and Matrona basilaris basilaris (MBB). Combined with other structural features of wing veins, such as number and thickness of cuticle layers, material composition, and cross‐sectional shape, resilin most probably has an effect on the vein′s material properties and the degree of elastic deformations. In order to elucidate the wing vein ultrastructure and the exact localisation of resilin in the internal layers of the vein cuticle, the approaches of bright‐field light microscopy, wide‐field fluorescence microscopy, confocal laser‐scanning microscopy, scanning electron microscopy and transmission electron microscopy were combined. Wing veins were shown to consist of up to six different cuticle layers and a single row of underlying epidermal cells. In wing veins of MBB, the latter are densely packed with light‐scattering spheres, previously shown to produce structural colours in the form of quasiordered arrays. Longitudinal and cross veins differ significantly in relative thickness of exo‐ and endocuticle, with cross veins showing a much thicker exocuticle. The presence of resilin in the unsclerotised endocuticle suggests its contribution to an increased energy storage and material flexibility, thus to the prevention of vein damage. This is especially important in the highly stressed longitudinal veins, which have much lower possibility to yield to applied loads with the aid of vein joints, as the cross veins do. These results may be relevant not only for biologists, but may also contribute to optimise the design of micro‐air vehicles.

Friction behavior of a microstructured polymer surface inspired by snake skin.

Summary The aim of this study was to understand the influence of microstructures found on ventral scales of the biological model, Lampropeltis getula californiae, the California King Snake, on the friction behavior. For this purpose, we compared snake-inspired anisotropic microstructured surfaces to other microstructured surfaces with isotropic and anisotropic geometry. To exclude that the friction measurements were influenced by physico-chemical variations, all friction measurements were performed on the same epoxy polymer. For frictional measurements a microtribometer was used. Original data were processed by fast Fourier transformation (FFT) with a zero frequency related to the average friction and other peaks resulting from periodic stick-slip behavior. The data showed that the specific ventral surface ornamentation of snakes does not only reduce the frictional coefficient and generate anisotropic frictional properties, but also reduces stick-slip vibrations during sliding, which might be an adaptation to reduce wear. Based on this extensive comparative study of different microstructured polymer samples, it was experimentally demonstrated that the friction-induced stick-slip behavior does not solely depend on the frictional coefficient of the contact pair.

Challenges and Solutions for Joining Polymer Materials

The different mechanisms contributing to adhesion between two polymer surfaces are summarized and described in individual examples, which represent either seminal works in the field of adhesion science or novel approaches to achieve polymer-polymer adhesion. A further objective of this article is the development of new methodologies to achieve strong adhesion between low surface energy polymers.

Dry friction of microstructured polymer surfaces inspired by snake skin

Summary The microstructure investigated in this study was inspired by the anisotropic microornamentation of scales from the ventral body side of the California King Snake (Lampropeltis getula californiae). Frictional properties of snake-inspired microstructured polymer surface (SIMPS) made of epoxy resin were characterised in contact with a smooth glass ball by a microtribometer in two perpendicular directions. The SIMPS exhibited a considerable frictional anisotropy: Frictional coefficients measured along the microstructure were about 33% lower than those measured in the opposite direction. Frictional coefficients were compared to those obtained on other types of surface microstructure: (i) smooth ones, (ii) rough ones, and (iii) ones with periodic groove-like microstructures of different dimensions. The results demonstrate the existence of a common pattern of interaction between two general effects that influence friction: (1) molecular interaction depending on real contact area and (2) the mechanical interlocking of both contacting surfaces. The strongest reduction of the frictional coefficient, compared to the smooth reference surface, was observed at a medium range of surface structure dimensions suggesting a trade-off between these two effects.

Direct observation of microcavitation in underwater adhesion of mushroom-shaped adhesive microstructure

Summary In this work we report on experiments aimed at testing the cavitation hypothesis [Varenberg, M.; Gorb, S. J. R. Soc., Interface 2008, 5, 383–385] proposed to explain the strong underwater adhesion of mushroom-shaped adhesive microstructures (MSAMSs). For this purpose, we measured the pull-off forces of individual MSAMSs by detaching them from a glass substrate under different wetting conditions and simultaneously video recording the detachment behavior at very high temporal resolution (54,000–100,000 fps). Although microcavitation was observed during the detachment of individual MSAMSs, which was a consequence of water inclusions present at the glass–MSAMS contact interface subjected to negative pressure (tension), the pull-off forces were consistently lower, around 50%, of those measured under ambient conditions. This result supports the assumption that the recently observed strong underwater adhesion of MSAMS is due to an air layer between individual MSAMSs [Kizilkan, E.; Heepe, L.; Gorb, S. N. Underwater adhesion of mushroom-shaped adhesive microstructure: An air-entrapment effect. In Biological and biomimetic adhesives: Challenges and opportunities; Santos, R.; Aldred, N.; Gorb, S. N.; Flammang, P., Eds.; The Royal Society of Chemistry: Cambridge, U.K., 2013; pp 65–71] rather than by cavitation. These results obtained due to the high-speed visualisation of the contact behavior at nanoscale-confined interfaces allow for a microscopic understanding of the underwater adhesion of MSAMSs and may aid in further development of artificial adhesive microstructures for applications in predominantly liquid environments.

First mushroom-shaped adhesive microstructure: A review

This letter reviews the adhesive and frictional properties of the first mushroom-shaped adhesivemicrostructure (MSAMS), which has come a long way from inspiration by the attachment devices evolved in beetles to a large-scale industrial production. It was shown to have an that about twice higher pull-off force compared to a smooth control made from the same materialmeasured on smooth substrates. Pull-off forces measured underwater are even higher than those in air. Moreover, it retained adhesive performance over thousands of attachment cycles and initial adhesive capability could be recovered by washing after being contaminated. In shearing, MSAMS exhibits reduced and stabilized friction in comparison with a smooth control, which demonstrated pronounced stick-slip motion, and shows zero pull-off force in a sheared state, allowing the adhesion to be switched on and off. The presence of a fluid in the contact zone showed adhesion enhancement on both smooth and rough substrates. All these features lead us to conclude that MSAMS may have practical potential in a variety of applications.

Comparative study of the fluid viscosity in tarsal hairy attachment systems of flies and beetles

Wet adhesive systems of insects strongly rely for their function on the formation of capillary bridges with the substrate. Studies on the chemical composition and evaporation dynamics of tarsal secretions strongly suggest a difference in chemistry of secretion in beetles and flies, both possessing hairy attachment devices. This difference is assumed to influence the viscosity of the secretion. Here, we applied a microrheological technique, based on the immersion of nanometric beads in the collected tarsal footprints, to estimate secretion viscosity in a beetle (Coccinella septempunctata) and a fly (Calliphora vicina). Both species studied possess distinct differences in viscosity, the median of which was calculated as 21.8 and 10.9 mPa s, respectively. We further present an approximate theoretical model to calculate the contact formation time of spatula-like terminal contact elements using the viscosity data of the covering fluid. The estimated contact formation time is proportional to the tarsal secretion viscosity and to the square of the contact radius of the contact element.