Laura Introzzi

Wetting of biopolymer coatings: contact angle kinetics and image analysis investigation

The surface wetting of five biopolymers, used as coating materials for a plastic film, was monitored over a span of 8 min by means of the optical contact angle technique. Because most of the total variation was observed to occur during the first 60 s, we decided to focus on this curtailed temporal window. Initial contact angle values (θ(0)) ranged from ∼91° for chitosan to ∼30° for pullulan. However, the water drop profile began to change immediately following drop deposition for all biocoatings, confirming that the concept of water contact angle equilibrium is not applicable to most biopolymers. First, a three-parameter decay equation [θ(t) = θ(0) exp(kt(n))] was fit to the experimental contact angle data to describe the kinetics of the contact angle change for each biocoating. Interestingly, the k constant correlated well with the contact angle evolution rate and the n exponent seemed to be somehow linked to the physicochemical phenomena underlying the overall kinetics process. Second, to achieve a reliable description of droplet evolution, the contact angle (CA) analysis was coupled with image analysis (IA) through a combined geometric/trigonometric approach. Absorption and spreading were the key factors governing the overall mechanism of surface wetting during the 60 s analysis, although the individual quantification of both phenomena demonstrated that spreading provided the largest contribution for all biopolymers, with the only exception of gelatin, which showed two quasi-equivalent and counterbalancing effects. The possible correlation between these two phenomena and the topography of the biopolymer surfaces are then discussed on the basis of atomic force microscopy analyses.

Self-assembled pullulan-silica oxygen barrier hybrid coatings for food packaging applications.

The scope of this study encompassed the evaluation of pullulan as a suitable biopolymer for the development of oxygen barrier coatings to be applied on poly(ethylene terephthalate) (PET), especially for food packaging applications. To enhance the oxygen barrier properties of the organic phase (pullulan) even at high relative humidity values, an inorganic phase (silica), obtained through in situ polymerization, was also utilized to obtain hybrid coatings via the sol-gel technique. Transmission electron microscopy (TEM) images and Fourier transform infrared (FT-IR) spectra showed that mixing the two phases yielded a three-dimensional hybrid network formed by self-assembly and mediated by the occurrence of new hydrogen-bond interactions at the intermolecular level, although the formation of new covalent bonds could not be excluded. The deposition of the hybrid coatings decreased the oxygen transmission rate (OTR) of the plastic substrate by up to 2 orders of magnitude under dry conditions. The best performance throughout the scanned humidity range (0%-80% relative humidity) was obtained for the formulation with the lowest amount of silica (that is, an organic/inorganic ratio equal to 3).

Ultrasound-Assisted Pullulan/Montmorillonite Bionanocomposite Coating with High Oxygen Barrier Properties

In this paper, the preparation and characterization of oxygen barrier pullulan sodium montmorillonite (Na(+)-MMT) nanocomposite coatings are presented for the first time. Full exfoliation of platelets during preparation of the coating water dispersions was mediated by ultrasonic treatment, which turned out to be a pivotal factor in the oxygen barrier performance of the final material even at high relative humidity (RH) conditions [oxygen permeability coefficients ~1.43 ± 0.39 and 258.05 ± 13.78 mL·μm·m(-2)·(24 h)(-1)·atm(-1) at 23 °C and 0% RH and 70% RH, respectively]. At the micro- and nanoscale, the reasons are discussed. The final morphology of the coatings revealed that clay lamellae were stacked on top of one another, probably due to the forced confinement of the platelets within the coating thickness after solvent evaporation. This was also confirmed by modeling the experimental oxygen permeability data with the well-known Nielsen and Cussler permeation theoretical models, which suggested a reasonable aspect ratio (α) of ~100. Electron microscopic analyses also disclosed a peculiar cell-like arrangement of the platelets. The stacking of the clay lamellae and the cell-like arrangement create the excellent oxygen barrier properties. Finally, we demonstrated that the slight haze increase in the bionanocomposite coating materials arising from the addition of the clays depends on the clay concentration but not so much on the sonication time, due to the balance of opposite effects after sonication (an increase in the number of scattering centers but a reduction in their size).

Surface properties and wear performances of siloxane-hydrogel contact lenses.

The low surface roughness of disposable contact lenses made of a new siloxane-hydrogel loaded with hyaluronic acid is reported, as studied by atomic force microscopy (AFM). Before the wear, the surface is characterized by out-of-plane and sharp structures, with maximum height of about 10 nm. After a wear of 8 h, evidence of two typical morphologies is provided and discussed. One morphology (sharp type) has a similar aspect as the unworn lenses with a slight increase in both the height and the number of the sharp peaks. The other morphology (smooth type) is characterized by troughs and bumpy structures. Wettability and clinical performances are also discussed, the latter deduced by the ocular-surface-disease index (OSDI). The main finding arising from this work is the indication of correlation between the change of the OSDI before and after wear and the lens surface characteristics obtained by AFM.

Self-assembled nanostructured biohybrid coatings by an integrated ‘sol–gel/intercalation’ approach

The combination of sol–gel technology and intercalation was investigated in this study as a strategy to develop bionanocomposite hybrid materials in the form of coatings with specifically intended oxygen barrier properties. To this goal, the exopolysaccharide pullulan was used as the organic phase, whereas tetraethyl orthosilicate (TEOS) and Na+–montmorillonite (MMT) were used as the metal alkoxide precursor and the nanobuilding blocks (NBB) for the sol–gel technology and the intercalation process, respectively. Complementary information from XRD and TEM analyses disclosed a new supramolecular organization arising from the self-assembly of NBB and pullulan, with the latter apparently intercalated between the clay platelets. Although affected by a rise in haze, the hybrid coatings exhibited outstanding oxygen barrier properties, with permeability coefficient values (P′O2) ranging from 0.89 mL μm m−2 (24 h)−1 atm−1 for a filler volume fraction (ϕ) = 0.017 to an impressive 0.15 mL μm m−2 (24 h)−1 atm−1 (ϕ = 0.095) under dry conditions. Modeling of P′O2 suggested a very tight structure under dry conditions, which yielded an apparent clays aspect ratio (α) ∼50, whereas in the hydrated state a more realistic α ∼ 100 was restored. This finding was further supported by SEM analysis, which also highlighted partial embrittlement of the final hybrid coatings.