Leo J. Small

Neutron irradiation effects on domain wall mobility and reversibility in lead zirconate titanate thin films

The effects of neutron-induced damage on the ferroelectric properties of thin film lead zirconate titanate (PZT) were investigated. Two sets of PbZr0.52Ti0.48O3 films of varying initial quality were irradiated in a research nuclear reactor up to a maximum 1 MeV equivalent neutron fluence of (5.16 ± 0.03) × 1015 cm−2. Changes in domain wall mobility and reversibility were characterized by polarization-electric field measurements, Rayleigh analysis, and analysis of first order reversal curves (FORC). With increasing fluence, extrinsic contributions to the small-signal permittivity diminished. Additionally, redistribution of irreversible hysterons towards higher coercive fields was observed accompanied by the formation of a secondary hysteron peak following exposure to high fluence levels. The changes are attributed to the radiation-induced formation of defect dipoles and other charged defects, which serve as effective domain wall pinning sites. Differences in damage accumulation rates with initial film qual...

Simple, benign, aqueous-based amination of polycarbonate surfaces

Polycarbonate is a desirable material for many applications due to its favorable mechanical and optical properties. Here, we report a simple, safe, environmentally friendly aqueous method that uses diamines to functionalize a polycarbonate surface with amino groups. The use of water as the solvent for the functionalization ensures that solvent induced swelling does not affect the optical or mechanical properties of the polycarbonate. We characterize the efficacy of the surface amination using X-ray photo spectroscopy, Fourier transform infrared spectroscopy (FT-IR), atomic force microscopy (AFM), and contact angle measurements. Furthermore, we demonstrate the ability of this facile method to serve as a foundation upon which other functionalities may be attached, including antifouling coatings and oriented membrane proteins.

Conical nanopores fabricated via a pressure-biased chemical etch

Controlling the size and shape of nanopores in polymer membranes can significantly impact transport of molecular or ionic species through these membranes. Here we describe a facile method to controllably form conical nanopores in ion-tracked polycarbonate membranes. Commercial polycarbonate ion-tracked membranes were placed between a concentrated alkaline solution and an acidic solution. By varying the height of the acidic solution, the hydrostatic pressure was controlled, regulating the acid flux through the nanopores. The resulting asymmetric etching of the membrane produced conical pores with controllable aspect ratios. Scanning electron microscopy of both the pores and nickel nanostructures electrolessly templated in the pores confirms their conical shape. This safe, straightforward approach obviates the need to use large voltages, currents, and/or plasma etching equipment traditionally employed to create conical nanopores.

Spontaneous aryldiazonium film formation on 440C stainless steel in nonaqueous environments.

The ability of three aryldiazonium salts to spontaneously assemble onto the surface of type 440C stainless steel is investigated in acetonitrile (ACN) and the model hydraulic fluids tributyl phosphate (TBP) and hexamethyldisiloxane (HMDS). Competition between native oxide formation and organic film growth at different diazonium salt concentrations is monitored by electrochemical impedance spectroscopy. At 1 mM diazonium salt, 70% of total assembly is complete within 10 min, though total surface coverage by organics is limited to ≈0.15 monolayers. Adding HCl to the electrolyte renders native oxide formation unfavorable, yet the diazonium molecules are still unable to the increase surface coverage over 1 M-10 μM HCl in solution. X-ray photoelectron spectroscopy confirms preferential bonding of organic molecules to iron over chromium, while secondary ion mass spectroscopy reveals the ability of these films to self-heal when mechanically removed or damaged. Aging the diazonium salts in these nonaqueous environments demonstrates that up to 90% of the original diazonium salt concentration remains after 21 days at room temperature, while increasing the temperature beyond 50 °C results in complete decomposition within 24 h, regardless of solvent-salt combination. It is concluded that the investigated diazonium molecules will not spontaneously form a continuous monolayer on 440C stainless steel immersed in ACN, TBP, or HMDS.

Direct Electrical Detection of Iodine Gas by a Novel Metal-Organic Framework Based Sensor

High-fidelity detection of iodine species is of utmost importance to the safety of the population in cases of nuclear accidents or advanced nuclear fuel reprocessing. Herein, we describe the success at using impedance spectroscopy to directly detect the real-time adsorption of I2 by a metal-organic framework zeolitic imidazolate framework (ZIF)-8-based sensor. Methanolic suspensions of ZIF-8 were dropcast onto platinum interdigitated electrodes, dried, and exposed to gaseous I2 at 25, 40, or 70 °C. Using an unoptimized sensor geometry, I2 was readily detected at 25 °C in air within 720 s of exposure. The specific response is attributed to the chemical selectivity of the ZIF-8 toward I2. Furthermore, equivalent circuit modeling of the impedance data indicates a >105× decrease in ZIF-8 resistance when 116 wt % I2 is adsorbed by ZIF-8 at 70 °C in air. This irreversible decrease in resistance is accompanied by an irreversible loss in the long-range crystallinity, as evidenced by X-ray diffraction and infrared spectroscopy. Air, argon, methanol, and water were found to produce minimal changes in ZIF-8 impedance. This report demonstrates how selective I2 adsorption by ZIF-8 can be leveraged to create a highly selective sensor using >105× changes in impedance response to enable the direct electrical detection of environmentally relevant gaseous toxins.

High-Throughput Measurement of Ionic Conductivity in Composition-Spread Thin Films

This paper demonstrates the feasibility of high-throughput investigation of ionic conductivity in oxygen-ion conductors. Yttria stabilized zirconia (YSZ) composition-spread thin films with nanometer-size grains were prepared by 90° off-axis reactive RF cosputtering. We compare results for two electrode configurations, namely, out-of-plane (parallel plate) and in-plane (planar interdigitated electrode) and find that the contribution from the intragrain conductivity in YSZ thin films (150 nm) is more explicit in the latter configuration because it greatly diminishes electrode effects. The intragrain oxygen ion conductivity of thin film YSZ was systematically measured as a function of yttria concentration over the range 2 mol % to 12 mol %. The results show that the measured conductivity of the YSZ thin films is close to that of corresponding bulk materials with a peak value around 3 × 10⁻⁴ S cm⁻¹ at 440 °C at the optimum Y₂O₃ concentration of 8 mol %. Validation of this technique means that it can be applied to novel chemical systems for which systematic bulk measurements have not been attempted.

Polyelectrolyte layer-by-layer deposition on nanoporous supports for ion selective membranes

This work demonstrates that the ionic selectivity and ionic conductivity of nanoporous membranes can be controlled independently via layer-by-layer (LbL) deposition of polyelectrolytes and subsequent selective cross-linking of these polymer layers. LbL deposition offers a scalable, inexpensive method to tune the ion transport properties of nanoporous membranes by sequentially dip coating layers of cationic polyethyleneimine and anionic poly(acrylic acid) onto polycarbonate membranes. The cationic and anionic polymers are self-assembled through electrostatic and hydrogen bonding interactions and are chemically crosslinked to both change the charge distribution and improve the intermolecular integrity of the deposited films. Both the thickness of the deposited coating and the use of chemical cross-linking agents influence charge transport properties significantly. Increased polyelectrolyte thickness increases the selectivity for cationic transport through the membranes while adding polyelectrolyte films decreases the ionic conductivity compared to an uncoated membrane. Once the nanopores are filled, no additional decrease in conductivity is observed with increasing film thickness and, upon cross-linking, a portion of the lost conductivity is recovered. The cross-linking agent also influences the ionic selectivity of the resulting polyelectrolyte membranes. Increased selectivity for cationic transport occurs when using glutaraldehyde as the cross-linking agent, as expected due to the selective cross-linking of primary amines that decreases the net positive charge. Together, these results inform deposition of chemically robust, highly conductive, ion-selective membranes onto inexpensive porous supports for applications ranging from energy storage to water purification.

Enhanced alkaline stability in a hafnium-substituted NaSICON ion conductor

We present here a multi-length scale integration of compositionally tailored NaSICON-based Na+ conductors to create a high Na+ conductivity system resistant to chemical attack in strongly alkaline aqueous environments. Using the Pourbaix Atlas as a generalized guide to chemical stability, we identify NaHf2P3O12 (NHP) as a candidate NaSICON material for enhanced chemical stability at pH > 12, and demonstrate the stability of NHP powders under accelerated aging conditions of 80 °C and pH = 13–15 for a variety of alkali metal cations. To compensate for the relatively low ionic conductivity of NHP, we develop a new low temperature (775 °C) alkoxide-based solution deposition chemistry to apply dense NHP thin films onto both platinized silicon wafers and bulk, high Na+ conductivity Na3Zr2Si2PO12 (NZSP) pellets. These NHP films display Na+ conductivities of 1.35 × 10−5 S cm−1 at 200 °C and an activation energy of 0.53 eV, similar to literature reports for bulk NHP pellets. Under aggressive conditions of 10 M KOH at 80 °C, NHP thin films successfully served as an alkaline-resistant barrier, extending the lifetime of NZSP pellets from 4.26 to 36.0 h. This integration of compositionally distinct Na+ conductors across disparate length scales (nm, mm) and processing techniques (chemically-derived, traditional powder) represents a promising new avenue by which Na+ conducting systems may be utilized in alkaline environments previously thought incompatible with ceramic Na+ conductors.